USA, Corporate Headquarters:
Graham-Field Health Products
2935 Northeast Parkway
Atlanta, Georgia 30360
telephone: 800-347-5678, 770-447-1609
fax: 800-726-0601, 678-291-3232
www.grahameld.com
© 2008 GF Health Products, Inc.
707A-INS-LAB-RevC08
Read this manual before operating the Labtron Digital Blood
Pressure Monitor. Save this manual for future reference.
707A-INS-LAB-RevC08
Item 707A,
707A X, 707A C
Digital Blood Pressure
Monitor
w
User Manual
707A-INS-LAB-RevC08-book.indd 1 1/3/08 11:36:34 AM
Labtron Digital Blood Pressure Monitor 2
Labtron Digital Blood Pressure Monitor 19
GF, Graham-Field, and Labtron are registered trademarks of GF Health Products, Inc.
Velcro is a registered trademark of Velcro Industries B.V.
Packaging, warranties, products, and specications are subject to change without notice.
GF Health Products, Inc. is not responsible for typographical errors.
CONTENTS
SAFETY GUIDELINES - PLEASE READ BEFORE USE ................................................................. 3
INTENDED USE ................................................................................................................................. 3
FEATURES ........................................................................................................................................
4
BATTERY INSTALLATION / REPLACEMENT ..................................................................................
5
BLOOD PRESSURE .......................................................................................................................... 5
PREPARING TO MEASURE BLOOD PRESSURE ................................................................... 6
MEASURING BLOOD PRESSURE ........................................................................................... 9
MAINTENANCE ...............................................................................................................................
13
TROUBLESHOOTING .....................................................................................................................
14
ERROR INDICATORS .............................................................................................................. 14
GENERAL TROUBLESHOOTING ........................................................................................... 15
SPECIFICATIONS * .........................................................................................................................
16
WARRANTY ..................................................................................................................................... 18
BLOOD PRESSURE MEASUREMENT LOG ..................................................................................
19
BLOOD PRESSURE MEASUREMENT LOG
Date
Time
Pulse
Body
Condition
1/1 1/1 1/1
60
80
100
120
140
160
180
200
220
240
mmHg
128
134
123
84
90
76
70
73
69
7:00
13:30
20:00
707A-INS-LAB-RevC08-book.indd 2 1/3/08 11:36:34 AM
Labtron Digital Blood Pressure Monitor 18
Labtron Digital Blood Pressure Monitor 3
WARRANTY
GF Health Products, Inc. warrants the Labtron Digital Blood Pressure Monitor Model 707A/707A X/707A C for a period of one year for
defects in workmanship and materials. During the warranty period,
defective items will be repaired or replaced at manufacturer’s option
at no charge.
SAFETY GUIDELINES - PLEASE READ BEFORE USE
Important! Read and understand these instructions before using the
Labtron® Digital Blood Pressure Monitor. If you do not understand
any part of these instructions, contact your medical professional or
Graham-Field dealer for direction in the use of this product.
If components are damaged or missing, contact your Graham-Field
dealer immediately. DO NOT use substitute parts.
GF Health Products, Inc. assumes no responsibility for any damage
or injury caused by improper installation or use of this product.
INTENDED USE
The Labtron Digital Blood Pressure Monitor is intended to measure
arterial blood pressure. This device is intended for use by adults,
and not for use by children except under the supervision of an
adult. This device is not intended to replace regular medical examinations. Review your procedure for using this monitor with your
physician, who is the only person qualied to interpret blood pressure monitor results.
707A-INS-LAB-RevC08-book.indd 3 1/3/08 11:36:34 AM
Labtron Digital Blood Pressure Monitor 4
Labtron Digital Blood Pressure Monitor 17
FEATURES
Main features of
the Digital Blood
Pressure Monitor,
referred to in this
manual, are shown
in the picture at
right.
cuff
cuff
hose
LCD
bulb
ON/OFF
button
exhaust valve
button
Digital Blood Pressure Monitor
Environmental
conditions
Operation 50°F ~ 104°F (10°C ~ 40°C), 10% ~ 85% RH
Storage &
transport
14°F ~ 140°F (-10°C ~ 60°C), 10% ~ 95% RH
Standard cited EN 1060-1 Noninvasive blood pressure measuring equipment
general requirements
EN 1060-3 Noninvasive blood pressure measuring equipment
supplementary requirements for electromechanical
blood pressure measuring systems
EN 60601-1 Safety requirements for medical electrical equipment
EN 606011-2
Electromagnetic compatibility and safety for medical
electrical equipment
EN 14971 Risk analysis for medical devices
* Specications are subject to change without notice
707A-INS-LAB-RevC08-book.indd 4 1/3/08 11:36:35 AM
Labtron Digital Blood Pressure Monitor 16
Labtron Digital Blood Pressure Monitor 5
Digital Blood Pressure
Monitor Model
707A, adult-size cuff, ts 7.5 in. - 12.2 in. (19-31cm) arm
707A X, large adult-size cuff, ts 11.8 in. - 17.7 in. (30-45cm) arm
707A C, small adult-size cuff, ts 5.1 in. - 7.9 in. (13-29cm) arm
Measurement method Oscillometric
Display Digital LCD
Measurement range Pressure 20-280mmHg, Pulse 40-180bpm
Measurement accuracy Pressure ±3mmHg, Pulse ±5%
Ination system Manual ination with air pumping bulb
Deation system Automatic deation
Power 1.5V (AAA) alkaline batteries X 4
Automatic power-off Approximately 3 minutes after measurement
Reference method for
clinical trials
Auscultatory measurement
Weight Approximately .75 lb (340g) without batteries
BATTERY INSTALLATION / REPLACEMENT
1. Slide the battery cover off in the direction of
the arrow.
2. Install or replace the four AAA batteries,
oriented as shown by battery compartment
diagram, into the battery compartment.
3. Replace the battery cover. Ensure that the
battery cover is securely fastened.
Note: Ensure that the batteries are correctly
installed. Incorrect installation will prevent the
device from operating.
BLOOD PRESSURE
Blood Pressure is a measure of the blood’s pressure in the
circulatory system, which changes constantly during the course of
the cardiac cycle. Blood pressure readings report two values. The
higher reading (systolic pressure) shows the highest pressure
O P E N
707A-INS-LAB-RevC08-book.indd 5 1/3/08 11:36:35 AM
Labtron Digital Blood Pressure Monitor 6
Labtron Digital Blood Pressure Monitor 15
in the arteries occurring when the heart contracts. The lower
reading (diastolic pressure) shows the lowest pressure in the
arteries, which occurs right before the heart contracts. Blood
pressure readings are written with the highest value rst, then the
lowest value. Readings of 120/80 are considered to be normal, with
high blood pressure being dened as a systolic pressure which is
140mmHg or more at rest and a diastolic pressure which is 90mmHg
or more at rest. Only a patient’s physician is qualied to determine
whether the readings obtained are normal for that person.
Preparing to measure blood pressure
1. Blood pressure uctuates continuously throughout the day. To
consistently track your blood pressure, try to take your blood
pressure at the same time each day.
2. Relax and remain still for 5 to 10 minutes before a blood pressure
measurement, and between blood pressure measurements.
3. Refrain from eating, smoking, and drinking, especially alcoholic
General troubleshooting
Problem Recommended Action
Nothing appears
in LCD
Ensure that batteries are correctly oriented in battery holder (polarity
matches battery case placement indicators)
No measurement
occurs
Ensure that cuff is positioned correctly
Go over measurement procedure; measure again
Blood pressure
measurements are
too high or
too low
Ensure that user and cuff are positioned as instructed
Rest your arm on a table so that the cuff is level with your heart during
measurement
Remain seated and still during entire measurement period
Refrain from hand and body movements during measurement
Blood pressure
measurements
vary
Your blood pressure can uctuate considerably throughout the day. All
of the following factors can inuence your blood pressure:
• Emotional state
• Daily activities / exercise
• Smoking
• Drinking alcoholic beverages
• Eating
• Taking certain medications
707A-INS-LAB-RevC08-book.indd 6 1/3/08 11:36:35 AM
Labtron Digital Blood Pressure Monitor 14
Labtron Digital Blood Pressure Monitor 7
TROUBLESHOOTING
Error indicators
Indication Cuff pressure reaches 330mmHg
Cause Twisted bladder inside cuff
Correction Ensure that bladder lies at within cuff
Indication "Err" displays, cuff pressure releases, then "0 pressure" displays
Cause Excessive arm movement or talking during measurement
Correction Turn monitor OFF then ON and measure again while remaining still
Indication Could not obtain pulse rate
Cause Cuff was too loosely applied, extremely weak pulse, or arrhythmia
Correction Reapply cuff and measure again; if problem persists after cuff is
correctly positioned, seek medical attention immediately
Batteries are exhausted. Replace with four new AAA alkaline batteries
beverages, before a measurement.
4. Remove any clothing on the upper arm to place the
cuff directly on the skin. Constriction of the upper
arm by clothing or a rolled-up sleeve, as shown at
right, may cause an inaccurate reading; remove any
constricting garments.
5. Sit down in a chair with back support
and place both feet on the oor.
6. Extend the arm from which the blood
pressure will be taken to the front or
side. Rest your hand, palm-up, on a
table as shown at right.
Note: Place the cuff at the same level as your heart to obtain accurate
measurements. Your heart is located slightly to the right of your left
armpit.
excessive
constriction
707A-INS-LAB-RevC08-book.indd 7 1/3/08 11:36:35 AM
Labtron Digital Blood Pressure Monitor 8
Labtron Digital Blood Pressure Monitor 13
7. Attach the cuff: Hold the area of the cuff where the
hose exits the cuff rmly against the inside of the
bare upper arm directly over the brachial artery,
and the bottom of the cuff approximately one inch
(2-3cm) above the elbow, as shown in the third picture at right. Never place the cuff over clothing.
Pull the opposite end of the cuff snugly around the
arm and secure with the Velcro® fastener. The cuff
should be snug, but not too tight. If one or two ngers can t between the cuff and the arm, the cuff
is properly secured. If you are unable to t the cuff
as described above, a smaller or larger cuff should
be used.
1 inch
MAINTENANCE
Recommended care and maintenance:
Do not drop or pull excessively on monitor components or subject them to strong impact.
Do not use monitor close to any device with a strong electrical eld such as television,
microwave oven, X-Ray equipment, etc.
Never inate cuff above 300mmHg. Never inate cuff unless it is positioned on an arm.
Do not expose the monitor components to direct sunlight, high temperature, or high humidity.
Do not put any part of monitor in contact with sharp objects which could pierce the material
and cause damage.
Do not dismantle or disassemble monitor components.
Cleaning Wipe off all components with a clean, dry cloth. Do not use solvents or other
petroleum-based cleaners. Do not press cuff with a hot iron.
Storage Always deate the cuff completely before storage.
Remove the batteries when the device is to be stored for extended periods of
time. Note: Removing the batteries will erase all readings in memory.
707A-INS-LAB-RevC08-book.indd 8 1/3/08 11:36:36 AM
Labtron Digital Blood Pressure Monitor 12
Labtron Digital Blood Pressure Monitor 9
7. If performing measurement for the rst time, repeat the measurement two or more times to ensure that you and cuff are positioned correctly and that results are accurate and consistent.
Record your results; there is a log provided, with examples, at the
end of this manual for this purpose. Always check with your physician to ensure that readings are performed correctly. If you have
concerns or questions about your results, always contact your
physician. Only your physician is qualified to analyze blood
pressure.
Measuring blood pressure
Symbol key: LCD symbols you may see during measurement
Deating
Inating
Measurement error
Measuring
Low battery
1. Ensure that cuff is properly placed and that you are positioned as
described in previous paragraphs.
2. Press the ON/OFF button. All LCD symbols will appear momentarily. If a downward arrow symbol displays, press the exhaust
valve button (see earlier labeled picture) located between the
ination bulb and the tube to release the residual pressure from
the cuff.
707A-INS-LAB-RevC08-book.indd 9 1/3/08 11:36:36 AM
Labtron Digital Blood Pressure Monitor 10
Labtron Digital Blood Pressure Monitor 11
Note: The low battery symbol will also appear at this time while the
monitor checks the power level. This does not indicate that the batteries are low unless the low battery symbol remains on continuously.
3. After "0" displays, pressurize the cuff by squeezing the bulb until
the pressure value displayed is 50mmHg above your usual systolic
pressure. If you do not know your usual systolic pressure, squeeze
the bulb just until 200mmHg displays.
4. The cuff will automatically deate after you stop pressurizing the
cuff. If an upward arrow symbol displays, you must inate the
cuff to a higher pressure than you did the rst time. If an upward
arrow does not display, the monitor is taking your measurement.
Remain calm and still to avoid causing any measurement error.
5. The systolic pressure, diastolic pressure,
and pulse will display in the format shown at
right. The device will completely deate when
measurement is nished. To accelerate defla-
tion, press the exhaust valve button.
Systolic
Diastolic
Pulse rate
Note: To stop measurement in progress for whatever reason, press the
exhaust valve button to release the pressure and turn off the device.
Note: If during measurement the power drops to an insufficient level,
the device will end the measurement and display the low battery symbol. Replace the batteries and repeat the measurement.
Note: If the device cannot detect your pulse, it will end the measurement. Wait several minutes, ensure that you and the cuff are positioned
properly, and try again.
6. The device will automatically shut off three minutes after completing a reading, or you may turn it off manually by pressing the
ON/OFF button.
707A-INS-LAB-RevC08-book.indd 10 1/3/08 11:36:36 AM
Loading...