GRAFTON 397/7697, 408/6295 Assembly Instructions Manual
Grafton - 3 Drawers Chest
397/7697
408/6295
Assembly Instructions
- Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Important – Please read these instructions fully before starting assembly
Dimensions
Width - 83cm
Depth - 43cm
Height - 86cm
Issue 1 - 05/05/15
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
.
Check you have all the
components and tools listed on
pages 2 and 3.
.
Remove all fittings from the
plastic bags and separate them
into their groups.
.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
.
Make sure you have enough
space to layout the parts before
starting.
.
Do not stand or put weight on
the product, this could cause
damage.
.
Assemble the item as close
to its final position (in the same
room) as possible.
.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
.
Parts of the assembly will be
easier with 2 people.
.
Dispose of all packaging
carefully and responsibly.
This product contain
Natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
.
Care and maintenance
.
.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
.
From time to time check
that there are no loose
screws on this unit.
.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Components - Panels
Please check you have all the panels listed below
2
1
5
6
7
8
9
10
12
13
14
15
16
11
3
2
4
Right back foot
Right side panel
Left side panel
Top panel
Drawer bottom x3
Back panel x 2
Drawer front x 3
Back rail
Bottom front rail
Drawer back x 3
Drawer left side x 3
Drawer right side x 3
Front rail x 3
Left back foot
Left front foot
Right front foot
(84.2 x 4.5cm)
(77.2 x 32.5cm)
(77.2 x 32.5cm)
(83 x 43cm)
(68.9 x 35cm)
(78.2 x 37.2cm)
(72.4 x 21.3cm)
(73 x 6cm)
(73 x 6cm)
(67.5 x 15cm)
(35 x 15cm)
(35 x 15cm)
(73 x 6.5cm)
(84.2 x 4.5cm)
(84.2 x 4.5cm)
(84.2 x 4.5cm)
3
2
m
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0
5
10 15 20 25 30 35 40
45
50
55
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
If you have damaged or missing components,
call the Customer Helpline: 03456 400 800
F
G H I
J
L M
N
Metal dowel x 38
Washer x 01
Wall strap x 01
Locking
nut x 38
30mm Screw x 12
16mm Screw x 1
14mm Screw x 30
Nail x 25
22mm Bolt x 06
Wooden dowel x 26
Handle x 06
Right runner x 03 pair
Left runner x 03 pair
O
H profile 712mm x 01
Assembly InstructionsAssembly Instructions
Step 1
Assembly Instructions
4
A
A
Attention:
Attention:
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
H
H
H
H
H
H
H
H
H
3
4
1
2
Fitting Metal dowels.
Screw metal dowels
in the parts indicated.
Insert metalNote:
dowels as far as
shown.
Do not over tighten.
A
Insert dowels into the
indicated parts.
H
A
A
A
A
10
3x
A
A
A
A
7
Loading...