Grafenthal PR-1000, PR-2000, PR-1500, PR-3000 User Manual

GRAFENTHAL® USV

PR-1000 PR-1500 PR-2000 PR-3000

Uninterruptible Power Supply System

USER MANUAL

GRAFENTHAL GmbH - User Manual UPS PR-1000/-1500/-2000/-3000

- 1 -

TABLE OF CONTENTS

1. Important Safety Warning………………………………………………………………………….

1-1. Transportation………………………………………………………………………………...

1-2. Preparation……………………………………………………………………………………

1-3. Installation…………………………………………………………………………………….

1-4. Operation……………………………………………………………………………………..

1-5. Maintenance, service and faults……………………………………………………………...

2. Installation and setup………………………………………………………………………………

2-1. Rear panel view……………………………………………………………………………...

2-2. Setup the UPS……………………………………………………………………………….

3. Operations…………………………………………………………………………………………

3-1. Button operation……………………………………………………………………………

3-2. LCD Panel…………………………………………………………………………………...

3-3. Audible Alarm……………………………………………………………………………….

3-4. LCD display wordings index………………………………………………………………..

3-5. UPS Setting………………………………………………………………………………….

3-6. Operating Mode Description……………………………………………………………….

3-7. Faults Reference Code………………………………………………………………………

3-8. Warning indicator……………………………………………………………………………

4. Troubleshooting………………………………………………………….....................................

5. Storage and Maintenance…………………………………………………………………………

6. Specifications………………………………………………………………………………………

GRAFENTHAL GmbH - User Manual UPS PR-1000/-1500/-2000/-3000

- 2 -

1. IMPORTANT SAFETY WARNING

Please comply with all warnings and operating instructions in this manual strictly. Save this manual properly and read carefully the following instructions before installing the unit. Do not operate this unit before reading through all safety information and operating instructions carefully

1-1. Transportation

› Please transport the UPS system only in the original package to protect against shock and

impact.

1-2. Preparation

› Condensation may occur if the UPS system is moved directly from cold to warm

environment. The UPS system must be absolutely dry before being installed. Please allow at least two hours for the UPS system to acclimate the environment.

› Do not install the UPS system near water or in moist environments. › Do not install the UPS system where it would be exposed to direct sunlight or near heater. › Do not block ventilation holes in the UPS housing.

1-3. Installation

› Do not connect appliances or devices which would overload the UPS system (e.g. laser

printers) to the UPS output sockets.

› Place cables in such a way that no one can step on or trip over them. › Do not connect domestic appliances such as hair dryers to UPS output sockets. › The UPS can be operated by any individuals with no previous experience. › Connect the UPS system only to an earthed shockproof outlet which must be easily

accessible and close to the UPS system.

› Please use only VDE-tested, CE-marked mains cable (e.g. the mains cable of your

computer) to connect the UPS system to the building wiring outlet (shockproof outlet).

› Please use only VDE-tested, CE-marked power cables to connect the loads to the UPS

system.

› When installing the equipment, it should ensure that the sum of the leakage current of the

UPS and the connected devices does not exceed 3.5mA.

1-4. Operation

› Do not disconnect the mains cable on the UPS system or the building wiring outlet

(shockproof socket outlet) during operations since this would cancel the protective earthing of the UPS system and of all connected loads.

› The UPS system features its own, internal current source (batteries). The UPS output

sockets or output terminals block may be electrically live even if the UPS system is not connected to the building wiring outlet.

› In order to fully disconnect the UPS system, first press the OFF/Enter button to disconnect

the mains.

› Prevent no fluids or other foreign objects from inside of the UPS system.

GRAFENTHAL GmbH - User Manual UPS PR-1000/-1500/-2000/-3000

- 3 -

1-5. Maintenance, service and faults

› The UPS system operates with hazardous voltages. Repairs may be carried out only by

qualified maintenance personnel.

› Caution - risk of electric shock. Even after the unit is disconnected from the mains (building

wiring outlet), components inside the UPS system are still connected to the battery and electrically live and dangerous.

› Before carrying out any kind of service and/or maintenance, disconnect the batteries and

verify that no current is present and no hazardous voltage exists in the terminals of high capability capacitor such as BUS-capacitors.

› Only persons are adequately familiar with batteries and with the required precautionary

measures may replace batteries and supervise operations. Unauthorized persons must be kept well away from the batteries.

› Caution - risk of electric shock. The battery circuit is not isolated from the input voltage.

Hazardous voltages may occur between the battery terminals and the ground. Before touching, please verify that no voltage is present!

› Batteries may cause electric shock and have a high short-circuit current. Please take the

precautionary measures specified below and any other measures necessary when working with batteries:

－remove wristwatches, rings and other metal objects －use only tools with insulated grips and handles.

› When changing batteries, install the same number and same type of batteries. › Do not attempt to dispose of batteries by burning them. This could cause battery explosion. › Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin and eyes.

It may be toxic.

› Please replace the fuse only with the same type and amperage in order to avoid fire hazards. › Do not dismantle the UPS system.

GRAFENTHAL GmbH - User Manual UPS PR-1000/-1500/-2000/-3000

- 4 -

2. INSTALLATION AND SETUP

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged. Please keep the original package in a safe place for future use. NOTE: There are two different types of online UPS: standard and long-run models. Please refer to the following model table.

Model

Type

Model

Type

PR-1000

Standard

PR-1000L

Long-run

PR-1500

PR-1500L

PR-2000

PR-2000L

PR-3000

PR-3000L

2-1. Rear panel view

PR-1000(L)/1500(L)

PR-2000(L)

PR-3000(L)

1. Programmable outlets: connect to non-critical loads.

2. Output receptacles: connect to mission-critical loads.

3. AC input

4. Input circuit breaker

5. Network/Fax/Modem surge protection

6. Emergency power off function connector (EPO)

7. USB communication port

8. RS-232 communication port

9. SNMP intelligent slot

10. External battery connection (only available for L model)

11. Output terminal

12. Output circuit breaker

GRAFENTHAL GmbH - User Manual UPS PR-1000/-1500/-2000/-3000

- 5 -

2-2. Setup the UPS Step 1: UPS input connection Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using extension cords.

 For 208/220/230/240VAC models:

The power cord is supplied in the UPS package.

 For 110/115/120/127VAC models: The power cord is attached to the UPS. The input plug is a

NEMA 5-15P for 1000, 1000L, 1500 and 1500L models, NEMA 5-20P for 2000 and 2000L models.

Note:

For Low voltage models

: Check if the site wiring fault indicator lights up in LCD panel. It will be illuminated when the UPS is plugged into an improperly wired utility power outlet (Refer to Troubleshooting section).

Step 2: UPS output connection

 For socket-type outputs, there two kinds of outputs: programmable outlets and general outlets.

Please connect non-critical devices to the programmable outlets and critical devices to the general outlets. During power failure, you may extend the backup time to critical devices by setting shorter backup time for non-critical devices.

 For terminal-type input or outputs, please follow below steps for the wiring configuration:

a) Remove the small cover of the terminal block b) Suggest using AWG14 or 2.1mm2 power cords. Suggest using WG12-10 or 3.3mm2-5.3mm2 power cords for NEMA type. c) Upon completion of the wiring configuration, please check whether the wires are securely

affixed.

d) Put the small cover back to the rear panel.

Step 3: Communication connection Communication port:

USB port RS-232 port Intelligent slot

To allow for unattended UPS shutdown/start-up and status monitoring, connect the communication cable one end to the USB/RS-232 port and the other to the communication port of your PC. With the monitoring software installed, you can schedule UPS shutdown/start-up and monitor UPS status through PC.

The UPS is equipped with intelligent slot perfect for either SNMP or AS400 card. When installing either SNMP or AS400 card in the UPS, it will provide advanced communication and monitoring options.

PS. USB port and RS-232 port can’t work at the same time.

Step 4: Network connection

Network/Fax/Phone surge port

Connect a single modem/phone/fax line into surge-protected “IN” outlet on the back panel of the UPS unit. Connect from “OUT” outlet to the equipment with another modem/fax/phone line cable.

+ 13 hidden pages

Grafenthal PR-1000, PR-2000, PR-1500, PR-3000 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual