Graco Children s 59775978 Users manual

2M15 / 2M16

Replacement Parts



To purchase parts or accessories or for warranty information in the United States, please contact us at the following:

www.gracobaby.com

1-800-345-4109

Product Features

Parent’s Unit Model 2M16 - 1 unit Model 2M15 - 2 units

Nursery Unit (PD115977) Model 2M16

(PD115976)

Channel Selector

ON/OFF

Clip

Green = batteries ok Red = batteries low

Power Volume:

Nursery Unit Model 2M15

ON/OFF

Up/Down

(PD115978)

Parent Finder

Channel Selector

Product Registration (USA)

To register your Graco product from within

the U.S.A. visit us online at

www.gracobaby.com/productregistration.

We currently do not accept product registrations

from those living outside the

United States of America.

Rechargeable

Vibe setting

Vibe ON/OFF

Green when charging

DC Adapter Jack with rubber cover

Docking Station (A3921) Model 2M16 -1 unit Model 2M15 - 2 units

Battery Cover

AC Adapter Model 2M16 - Qty. 2

Model 2M15 - Qty. 3

Battery Pack Model 2M16 - qty.1 Model 2M15 - qty.2

GRACO

DC Adapter Jack

Failure to follow these warnings and the assembly instructions could result in serious injury or death.

This device is designed only to monitor the sounds of your child. It will not alert you to your child’s silent activities. When using the monitor, you must still provide the supervision necessary for the continued safety of your child. This product is not designed or intended for use as a medical monitor. Always be sure that both the transmitter and receiver are working properly and are within range of each other.

• STRANGULATION HAZARD. Keep the adapter cords out of the reach of children. Do not use with extension cords.

• DO NOT place the Nursery Unit or its cord within your child’s reach. Do not put the Nursery Unit inside a crib or play yard.

• Use ONLY with 110-120 volt AC electrical outlets.

• Protect the AC adapter cords. Place them so they are not walked on or pinched by furniture or other items.

• Allow for proper ventilation when units are in use. Do not cover the Nursery Unit or Parent Units with any object such

as a blanket. Do not place it in a drawer or in any location which would muffle the sound or interfere with the normal flow of air.

• DO NOT immerse any part of the Nursery Unit, Parent Units, or docking station in water. Clean only with a dry cloth.

• DO NOT place unit near water and moisture. Do not use the Nursery Unit outdoors. Do not use the Nursery Unit near possible

wet areas, such as a bathtub, shower, wash basin, sink, laundry tub, swimming pool, wet basement, etc.

• Keep Nursery Unit away from heat sources, such as fireplaces, radiators, stoves, and TVs or other appliances. Heat can damage the case or electrical parts.

• DO NOT use the Nursery Unit if:

• The adapter cords or plugs have been damaged.

• The unit has been exposed to liquids.

• Unit has been dropped or is damaged.

• DO NOT OPEN THE NURSERY UNIT, PARENT UNITS, DOCKING STATION OR ADAPTERS. No user-serviceable parts inside.

Risk of electrical shock, fire or death.

• The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.9”) from all persons

and must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Statement:

Modifications not authorized by the manufacturer may void users authority to operate this device.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

Graco Children’s Products

2M15/2M16

150 Oaklands Blvd. Exton, PA 19341 1-800-345-4109

Battery Installation

Parent Unit

• The battery must be plugged into the Parent Unit before the

unit will be ready for use. Remove the battery door cover on the Parent Unit with a key or flat blade screw driver. Remove the battery pack from the packaging and plug into the back of the unit. Place the battery pack into the recess and press the wire into the slot on the side. Replace the battery door.

Nursery Unit

• Turn the unit over, and use screw driver to remove the battery door.

• Place 3-AAA (1.5V-LR03) batteries into the battery compartment. Note

the proper orientation of the batteries.

• Place the battery door back on the unit.

• Please remove a dead battery promptly. A dead battery left in the unit

may leak, damaging your unit.

• Do not attempt to recharge a non-rechargeable battery.

• A rechargeable battery CANNOT be recharged by plugging the AC

adapter into the Nursery Unit.

• Remove the batteries from the unit if it is no longer being used or will

be stored for an extended period of time.

Batteries should be disposed of properly

by recycling.

Plug in cord

Using AC Adapters

• The Parent Unit(s) can use either the rechargeable battery that comes with the unit or standard 120 volt AC household current. The Nursery Unit uses 3-AAA (1.5V-LR03) batteries or standard 120 volt AC household current.

• To use AC adapters, plug the connector on the cord into the AC adapter jack on the side of the Parent Unit (under the rubber cover) and the back of the Nursery Unit. If using the docking station, plug the AC adapter jack into the back of the

docking station. The Parent Unit may now be placed in the docking station. Then plug adapter into a standard wall outlet.

• Use ONLY the Graco adapters included with the unit. Do not use these adapters with other equipment under any circumstances.

• If units do not work, check that AC adapters are plugged into working outlets.

• When electricity is off (from a power failure, etc.), the Nursery Unit will operate on 3-AAA (1.5V-LR03) batteries. If the Power LED is not lit, turn the power off and then back on to the Nursery Unit. A green LED indicates that the batteries are fine. A red LED indicates that the batteries are low. If the LED does not light at all, then replace the batteries. The Parent Unit will operate

if the rechargeable battery is charged.

Selecting Channels

• In case you are experiencing some interference, the channel on the Nursery Unit can be changed by pressing the “ch” button on the side of the unit. The Parent Unit will automatically scan all of the available channels until it locks on to the

Nursery Unit. If you are still experiencing interference, press the channel button on the side of the Nursery Unit up to 6

times until a good channel is found.

2 3

Low Battery Indication

Parent Unit

• When the battery is low in the parent unit, the LED bar on the side of the unit will change from green to red and you will hear a series of 3 audible beeps every 5 seconds. If operated too long on a low battery, you may also experience a poor signal and the connection LED on the front of the parent unit may change from green to red and you will begin to hear a

continuous audible beep from the Parent Unit.

• You may either turn off the unit, plug in the A/C adapter or place the unit in the docking station to recharge the batteries.

Nursery Unit

• When the batteries are low in the Nursery Unit, the power LED will change from green to red. You may also experience a poor signal and the connection LED on the front of the Parent Unit may change from green to red and you will begin to

hear the Parent Unit beep.

• You may either turn off the unit, plug in the A/C adapter or replace the batteries.

Out of Range Indication

• If the Parent Unit begins to lose the signal from the Nursery Unit, the connection LED (bottom Sound Light LED) will change

from green to red. Additionally, a continuous audible beep will be generated to warn the user that the connection to the Nursery unit has been lost.

• Immediately move the Parent Unit closer to the Nursery Unit to regain connection.

• Once connection has been re-gained, the connection LED will change from red to green and the audible beep will stop.

***Note: It is not uncommon for the Parent Unit to occasionally lose and regain connection with the Nursery

Unit in environments that have a significant amount of obstructions.

Setting Up the Baby Monitor

***NOTE: It is very important that the steps below be followed for first time power-up.

1. For optimum operation, it is best to charge the batteries in the Parent Units for at least 16 hours prior to use. The rechargeable batteries need to be installed into the Parent Unit before charging - refer to the “Battery Installation” section. DO NOT turn on

power while the unit is charging for the first time.

2. Place the Nursery Unit within 10 feet (3 meters) of your baby. Plug an AC adapter into the jack on the back of the Nursery Unit. Plug it into a working 120 volt AC outlet.

3. Aim the Nursery Unit toward your baby. Check that there are no walls or large objects that could block sound transmission.

4. Place the Parent Unit within five (5) feet (1.5 meters) of the Nursery Unit and turn on the Parent Unit using the On/Off switch on the side of the unit. All of the Sound Light LEDs will illuminate, and the bottom LED will be red. You will also hear a single

audible beep.

5. Turn on the Nursery Unit using the On/Off switch on the side. The green power light should come on.

6. Within a few seconds, the Parent Unit will lock on to the Nursery Unit and the top four (4) green LEDs will shut off. A second later, you will hear a series of beeps and the connection LED should change from red to green. Your monitor is now

ready for use.

Operation

To Listen To Baby

• Turn on Nursery Unit using the ON/OFF switch.

• Turn on one or both Parent Units using the ON/OFF switch.

• Adjust the volume on the Parent Unit by pressing the Volume Up/Down buttons. Note that the Sound Lights LEDs

illuminate as the volume button is pressed up or down to provide a visual feedback for the volume level. The unit will beep louder or softer depending on the volume level.

• The Sound Lights on the Parent Unit will illuminate as your child (or other objects) make noise near the Nursery Unit. Please note that the Sound Lights and volume control on the Parent Unit are independent of each other. With the volume turned all the way down, the Sound Lights will still illuminate as your child (or other objects) make noise near the Nursery Unit.

Parent Finder Feature

• Some units come equipped with a Parent Finder feature. This feature will allow you to locate a misplaced Parent Unit as

long as the Parent Unit is powered on and within range of the Nursery Unit.

• To activate, press the “PF” button on the side of the Nursery Unit (the Nursery Unit needs to be ON).

• The Parent Unit will generate an audible beep every second and the soundlights will flash on and off.

• Once the Parent Unit is located, the audible beep can be shut-off by pressing any button on the Parent Unit.

Vibration Alert Feature

1.To turn on the Vibration Alert Feature, set the switch on the side of the parent unit to on.

2. To adjust the level at which the vibration alert is activated, press and hold the “Vibe” button on the side of the parent unit. The sound lights will illuminate to show the vibration alert adjustment setting. Press the volume UP/DOWN switch to change the setting. A lower sound light setting will make the vibration activate for quieter sounds. A higher sound light

setting will make the vibration activate for louder sounds. When the sound in the nursery goes above the sound light level you choose, the vibration alert will be activated.

3. Release the “Vibe” Button.

TroubleShooting

DO NOT ATTEMPT to modify the unit. Any modifications to the transmitter and/or receiver can void the

operator’s authority to operate the equipment.

Most problems have a simple solution. First, check

that:

• Power is turned ON for both units

• Both units are plugged in (or batteries are fresh in Nursery Unit and fully charged in Parent Unit)

• Electrical outlet works

• Volume is turned up on Parent Unit

• Parent Unit is in range of the Nursery Unit

No Sound

• Battery dead or weak — replace or use AC adapter.

• AC adapter not properly connected — check the connections.

• Nursery Unit covered or blocked — remove the obstruction.



• Nursery Unit too far from baby — move closer.

• Large objects blocking the signal — try repositioning Nursery

Unit.

• Volume setting too low — turn it up.

Static

• Interference from other electrical equipment — eliminate cause of static (TVs, mixers, computers, fans, fluorescent lights, light dimmers, etc.)

• Parent Unit too far from Nursery Unit — move them

closer.

• Significant amount of obstructions between Parent Unit and Nursery Unit such as walls, ceilings & buildings. Try moving the Nursery Unit to another part of the room.

• Change channel on Nursery Unit.

Shrill Sound (Feedback)

• Nursery Unit and Parent Unit too close together — move them farther apart.

• Volume set too high — lower the volume.



•

All of the sound lights are illuminated and the unit beeps — Go to Pairing Parent and Child Unit section.

Pairing Parent Unit and Child Unit.

To ensure privacy, your Parent Unit is paired with your

Nursery Unit at the factory. Your Parent Unit will not work

with any other Nursery Unit.

If Parent Unit won’t lock onto the Nursery Unit, or you

purchased a new Nursery Unit, follow the procedure below

to pair the Parent Unit and Nursery Unit. If you purchased a new Parent Unit, skip Step 1. The new Parent Unit is ready

to pair with your Nursery Unit.

1. Erase the Pairing from the Parent Unit.

•Turn the Parent Unit off.

•Hold the Volume Down Button on the Parent Unit while pressing the On/Off Button. Continue to hold the Volume Down Button until you hear a single beep and all of the Sound Lights illuminate briefly.

•Release the Volume Down Button.

•Press and hold the Volume Down Button again.

•Within 2 seconds you will hear a beep. Release the Volume Down Button. All of the SoundLights and the red Loss Connection LED will be lit. The Parent Unit is ready to pair

with Nursery Unit.

2. Pair the Parent Unit with Nursery.

•Place Nursery Unit in the same room, five (5) feet (1.5 meters) away from the Parent Unit.

•Turn on Nursery Unit using the On/Off Button on the side.

The green power light should come on.

•Within a few seconds, the Parent Unit will find the Nursery Unit. The SoundLights will shut off and the Parent Unit will

beep. The Parent Unit is now paired with Nursery Unit.

3. Repeat this procedure if you need to pair another Parent Unit with the Nursery Unit.

Nothing happened when I turned on the Nursery Unit. What do I do?

•First try turning the Nursery Unit off, and then on again.

•If the Parent Unit still does not pair with the Nursery Unit, press the Channel Button on the Nursery Unit, then turn the

Nursery Unit off, and then on again.

Testing the System

It is VERY IMPORTANT to test the system when first set up, and at regular times thereafter. Test the units if you

suspect they may have been damaged or have not been used for a long time.

1. If two adults are present, have one take the Parent Units to different locations, trying various volume settings, while the

other speaks into the Nursery Unit.

2. If only one adult is available, place a ticking clock, radio, or other sound-producing device near the Nursery Unit to test it.

3. When testing, keep the level of your child’s sounds in mind, and adjust the volume accordingly.

4. If there is sound interference, switch the Nursery Unit and the Parent Units to the other channel setting.

+ 2 hidden pages

Graco Children s 59775978 Users manual

Specifications and Main Features

Frequently Asked Questions

User Manual