Smart Seat
ALL-IN-ONE CARSEAT
Child Restraint
Owner’s Manual
READ THIS MANUAL.
Do not install or use this child restraint until you read
and understand the instructions in this manual.
FAILURE TO PROPERLY USE THIS CHILD
RESTRAINT INCREASES THE RISK OF SERIOUS
INJURY OR DEATH IN A SUDDEN STOP OR CRASH.
*UDFR 86
PD163434A
TM
Before you begin
1.0 Warnings to Parents and
Other Users
2.0 Registration Information
2.1 Register Your Child
Restraint
2.2 Recall Information
2.3 If You Need Help
3.0 Useful Information
3.1 Certication
3.2 Child Restraint Useful Life
3.3 Second Hand Child
Restraint
4.0 Assembly
4.1 Attaching LATCH Storage
Compartment
Table of Contents
4.2 Attaching Cupholder
5.0 Features
5.1 Child Restraint
5.2 Base
10
10
11
11
11
11
11
11
12
12
12
14
14
16
6.0 Height and Weight
Limitations
4
6.1 Rear-Facing with base
6.2 Forward-Facing with base
6.3 Booster WITHOUT base
7.0 Choosing an Appropriate
Vehicle Seat Location
7.1 Vehicle Seat Location
Requirements
7.2 Vehicle Seat Belt
Requirements
7.3 SAFE Vehicle Seat Belt
Systems
7.4 For Built-in Harness Only
7.5 WITH or WITHOUT Built-in
Harness
7.6 UNSAFE Vehicle Belt
Systems
8.0 LATCH
8.1 What is LATCH?
8.2 LATCH System
18
19
20
21
22
22
23
23
24
24
25
27
27
29
Installation
9.0 Installing Base Using
Vehicle Seat Belt
10.0 Installing Base Using
LATCH
11.0 REAR-FACING
INSTALLATION
12.0 FORWARD-FACING
INSTALLATION
13.0 Tether Use
14.0 Tether and LATCH Storage
14.1 Tether Storage
14.2 LATCH Storage
15.0 Harness System
15.1 Harness Strap
15.2 Chest Clip
15.3 Buckle
15.4 Crotch Strap
16.0 Accessories
16.1 Body Support
(on certain models)
16.2 Harness Covers & Crotch
Strap Cover (on certain
models)
17.0 Using Recline
18.0 Securing Child in Child
Restraint
30
18.1 Placing Child in Child
Restraint
32
18.2 Check Harness System
18.3 Adjusting Head
34
Support/Harness Straps
19.0 Booster Installation
36
19.1 Storing Harness
19.2 Using Child Restraint in
38
Booster Mode
39
19.3 Securing Child in
39
Booster Seat and Vehicle
39
19.4 Adjusting Head
40
Support in Booster Mode
40
20.0 Additional Information
40
20.1 Adjusting Armrest
40
20.2 Removing Seat Cover
40
20.3 Airplane Use
42
20.4 Care and Maintenance
21.0 Replacement Parts,
42
Warranty, and Owner’s
Manual Storage
43
44
46
46
48
49
50
50
52
54
56
57
57
58
59
59
60
Table of Contents
1.0 Warnings to Parents and Other Users
• DO NOT PLACE THIS CHILD RESTRAINT IN A
VEHICLE SEATING LOCATION THAT HAS
A FRONT AIR BAG. If an air bag inates, it can hit
the child and child restraint with great force and
cause serious injury or death to your child. Check
vehicle owner’s manual for information about side
air bags and child restraint installation.
• No child restraint can guarantee protection from injury in every situation.
However, proper use of this child restraint reduces the risk of serious injury or
death to your child.
• FAILURE TO PROPERLY USE THIS CHILD RESTRAINT increases the risk of
serious injury or death in a sharp turn, sudden stop or crash. Your child’s safety
depends on you installing and using this child restraint correctly. Failure to
follow these instructions and child restraint labels can result in child striking the
vehicle’s interior during a sudden stop or crash.
• EVEN IF USING THIS CHILD RESTRAINT seems easy to gure out on your own,
it is very important to READ THE OWNER’S MANUAL and the vehicle owner’s
manual.
• Your child’s safety depends on:
1. CHOOSING THE CORRECT MODE OF USE for the child restraint depending
on your child’s size. Infants less than 20 lbs. must use this child restraint
rear-facing.
2. SELECTING A SUITABLE LOCATION for the child restraint in your vehicle.
Some seating positions, such as those equipped with air bags, may not be
safe locations for this child restraint.
3. PROPERLY ROUTING THE VEHICLE SEAT BELT OR LATCH.
4. PROPERLY SECURING THE CHILD RESTRAINT IN THE VEHICLE using a
seat belt designed to restrain a child restraint or by using LATCH. Many seat
belts are NOT safe to use with this child restraint, even though they can easily
be threaded through or around the child restraint! Vehicle seat belt system
MUST hold child restraint securely. Not all vehicle seat belts can be used with
a child restraint. If vehicle seat belt does not hold child restraint securely, read
“7.0 Choosing An Appropriate Vehicle Seat Location, p. 22-26”.
5. PROPERLY SECURING YOUR CHILD IN THE CHILD RESTRAINT.
• NEVER LEAVE YOUR CHILD UNATTENDED.
• YOU MUST READ your vehicle owner’s manual on child restraint use.
• REARFACING child restraint must be properly leveled:
• Too reclined can result in injury or ejection.
• Too upright can result in breathing diculties.
• NEVER LEAVE CHILD UNATTENDED, even when sleeping. Child may become
tangled in harness straps and suocate or strangle.
• According to accident statistics, CHILDREN ARE SAFER WHEN PROPERLY
RESTRAINED IN REAR VEHICLE SEATING POSITION, RATHER THAN FRONT
SEATING POSITIONS. For a vehicle with a front passenger air bag, refer to your
vehicle owner’s manual as well as these instructions for child restraint installation.
• SECURE CHILDREN in rear seat of vehicle whenever possible.
• SERIOUS CRIPPLING INJURY OR DEATH can result if infant faces front of
vehicle. The American Academy of Pediatrics recommends that children should
remain rear-facing for as long as possible, but be at least one year of age before
being positioned forward-facing.
• SOME SPECIAL NEEDS CHILDREN, such as pre-term babies or those who have
tested positive for positional apnea, may be at increased risk of suering
breathing or other diculties in a child restraint. If your child has special needs,
we recommend that you have your physician or hospital sta evaluate your child
and recommend the proper child restraint or car bed before using this product.
• DO NOT remove LATCH system from child restraint. If using vehicle seat belt
to secure child restraint, LATCH connectors must be stored. (see section “14.0
TETHER AND LATCH STORAGE, p. 39”.)
• NEVER ATTACH two LATCH connectors
to one vehicle lower anchor point unless
specically allowed by the vehicle
manufacturer.
• DO NOT INSTALL OR USE THIS CHILD RESTRAINT AND BASE UNTIL YOU
READ AND UNDERSTAND THE INSTRUCTIONS IN THIS MANUAL AND IN
YOUR VEHICLE OWNER’S MANUAL. DO NOT let others install or use the child
restraint unless they understand how to use it.
• IF CHILD RESTRAINT IS IN A CRASH, it must be replaced. DO NOT use it again!
A crash can cause unseen damage and using it again could result in serious
injury or death. DO NOT use child restraint if it is damaged or missing parts.
DO NOT use a cut, frayed or damaged child restraint harness, vehicle seat belt or
LATCH belts.
• NEVER LEAVE A CHILD RESTRAINT and base unsecured in your vehicle. An
unsecured child restraint or base can be thrown around and may injure
occupants in a sharp turn, sudden stop or crash. Remove it or make sure that it is
securely belted in the vehicle. If not using LATCH, make sure unsecured LATCH
connectors are properly stored on base.
• NEVER GIVE THIS CHILD RESTRAINT to someone else without also giving
them this manual.
DO NOT use accessories or parts other than those provided by Graco. Their use
•
could alter the performance of the child restraint.
• NEVER USE A SECONDHAND CHILD RESTRAINT or a child restraint whose
history you do not know.
• DO NOT MODIFY YOUR CHILD RESTRAINT or use any accessories or parts
supplied by other manufacturers.
• THE CHILD RESTRAINT CAN BECOME VERY HOT IF LEFT IN THE SUN. Always
touch the surface of any metal or plastic parts before putting your child in the
child restraint.
• DO NOT use child restraint with any stroller.
• DO NOT allow the liquid in the level indicator to be ingested or come into
contact with the eyes.
Model Number:
Manufactured in:
Purchase Date:
2.1 Register Your Child Restraint
Please ll in the above information. The model number and manufactured
in (date) can be found on a label on the child restraint. Fill out the prepaid
registration postcard attached to the harness and mail it today.
Child restraints could be recalled for safety reasons. You must register this
restraint to be reached in a recall. Send your name, address, and the
restraint’s model number and manufacturing date to:
Graco Children’s Products Inc.
2.0 Registration Information
150 Oaklands Blvd. Exton, PA, 19341
or call 1-800-345-4109
or register online at:
http://www.gracobaby.com/carseatregistration
2.2 For Recall Information
Call the U.S. Government’s Vehicle Safety Hotline at: 1-888-327-4236
(TTY:1-800-424-9153), or go to http://www.NHTSA.gov or contact Graco:
1-800-345-4109
or www.gracobaby.com
2.3 If You Need Help
Please contact our Customer Service Department with any questions you may
have concerning parts, use, or maintenance. When you contact us, please have
your product’s model and manufactured in (date) ready so that we may help you
eciently. These numbers can be found on a label on the child restraint.
USA: 1-800-345-4109
or www.gracobaby.com
3.0 Useful Information
3.1 Certication
THIS CHILD RESTRAINT
CONFORMS to all
applicable requirements
of Federal Motor Vehicle
Safety Standard 213 and
is certied for use in
motor vehicles.
3.2 Child Restraint Useful Life
STOP using child restraint and throw it away after
the date MOLDED into the child restraint.
Do not use this child restraint 10 years
Look For:
after the date of manufacture.
3.3 Second Hand Child Restraint
Graco Children’s Products Inc. advises against loaning
or passing along a child restraint.
4.1 Attaching LATCH Storage Compartment
NEVER use without LATCH storage compartment or
cupholder attached.
P
D
1
5
• Insert LATCH storage compartment under metal tube into bottom of
base as shown A.
• Line tabs on bottom of LATCH storage compartment with openings in
A
5
9
0
9
child restraint B.
• Push into base until you hear a click C.
4.2 Attaching Cupholder
NEVER place sharp or pointed objects in a
cupholder. In a crash, these objects could hit your
4.0 Assembly
• Remove seat pad from right hand side of the child restraint as child sits in
restraint D.
• Insert cupholder into opening in child restraint E.
• Rotate cupholder down, until you hear a click, to lock into place F.
• Wrap seat pad back around cupholder and side of child restraint G.
• Tuck fabric around cupholder and lock knob H.
child and cause serious injuries.
A B
CLICK!
C
CLICK!
D
E
G H
F
5.1 Child Restraint
N
5.0 Features
D
A
B
C
E
G
F
M
O
L
K
P
J
Q
I
H
A
Harness slots
B
Harness buckle
C
Crotch strap
D
Cupholder
E
Harness release lever
F
Harness adjustment strap
G
Recline handle
H
Lock knobs
I
Armrest
J
Chest clip
K
Harness strap
L
Level indicator
M
Head support
N
Head support release
O
Tether storage
P
Tether *
Q
Instruction manual storage
*Vehicles are now (or can
be) equipped with tether
anchor points behind
some seats. A tether
anchors the top of the
child restraint to the body
of the vehicle. When used
properly with the vehicle
seat belt or LATCH, a
tether helps reduce injury
in a sudden stop or crash.
5.2 BASE
R
S
T
5.0 Features
NOTE: Only use base with
Smart Seat™ All-In-One Carseat.
X
W
V
U
Y
Z
R
Vehicle belt/LATCH path
S
Child restraint pin guides
T
Lock identication window
U
LATCH connector
V
LATCH adjustment belt
W
LATCH belt **
X
Seat belt lock-o
Y
LATCH storage compartment
Z
LATCH (stored)
**United States Federal Motor Vehicle
Safety Standards have dened a new
system for installing child restraints in
vehicles. The system is called LATCH.
LATCH may ONLY be used IN PLACE of
vehicle belt if vehicle is equipped with
LATCH anchor points. Please refer to
vehicle owner’s manual for LATCH
in vehicles.
FAILURE TO USE CHILD RESTRAINT IN A MANNER
APPROPRIATE FOR YOUR CHILD’S SIZE MAY
INCREASE THE RISK OF SERIOUS INJURY OR
DEATH. Instructions for the use of this child restraint dier greatly depending on
the size of your child. Be sure you are using the child restraint in the correct mode
and with the correct features for your child.
Rear-Facing with base
5 lbs-20 lbs
(2.2 kg-9 kg)
and up to
1 year
MUST BE
REAR
FACING
20 lbs-40 lbs
(9 kg-18.1 kg)
and
Top of head
AT LEAST 1”
(2.54 cm)
BELOW top of
head support
Forward-Facing with base
6.0 Height & Weight Limits
Booster WITHOUT Base
20 lbs-39 lbs
(9 kg-17.7 kg)
At least 1 year
old and can
sit upright
unassisted
40 lbs-65 lbs
(18.1 kg-29.5 kg)
MAX HEIGHT
50” (127 cm)
Shoulders are
BELOW top harness
slot position
30 lbs-65 lbs
(13.6 kg-29.5 kg)
IF Shoulders are
ABOVE top
harness slot position
approx. 3-10 years
65 lbs-100 lbs
(29.5 kg-45 kg)
MAX HEIGHT
57” (145 CM)
Top of ears are BELOW
top of booster seat
6.1 Rear-facing with base: 5 to 40 lbs. (2.2-18.1 Kg)
• Infants who weigh less than 20 lbs. (9 kg) MUST be rear-facing.
• Infants or toddlers 20 to 40 lbs. (9 to 18.1 kg) may be
rear-facing.
IMPORTANT: This child restraint is certied for use rear-facing
with children up to 40 lbs. (18.1 kg).
However, some children approaching 40 lbs. (18.1 kg) may be
too tall to t
(2.54 cm) below the top of the head support.
• Child should use child restraint forward-facing only if child is
over 20 lbs. (9 kg) and can sit upright unassisted. (*)
*
The American Academy of Pediatrics recommends that children should be at least
one year of age before being positioned forward-facing. They also recommend that
the child should ride rear-facing as long as possible or to the extent permitted by
the car seat.
rear-facing. Top of head must be at least 1”
1” (2.54 cm)
Preterm or Low Birthweight Infants
A preterm infant or low birth weight infant may be at special risk in a vehicle or
aircraft.
According to the American Academy of Pediatrics, these infants may suer
breathing diculties if improperly reclined in a child restraint.
Graco advises that you have your physician or hospital sta evaluate your infant and
recommend the proper child restraint or car bed before you and your infant leave
the hospital.
6.2 Forward-facing with base: 20 to 65 lbs. (9 to 29.5 kg)
WITH BUILTIN HARNESS SYSTEM:
• Child must not exceed 50 inches (127 cm)
• At least one year old.
• Toddlers 20 to 65 lbs. (9 to 29.5 kg) who are capable
of sitting upright unassisted may be forward-facing. If
unable
to sit upright unassisted, use
40 lbs.
• Toddlers 40 to 65 lbs. (18.1 to 29.5 kg) and up to 50 inches
(127 cm) tall MUST be forward-facing.
• Shoulders are BELOW top harness slot/head support height.
If shoulders are above harness slots, child is too large
for forward-facing with built-in harness.
rear-facing when below
6.3 Booster WITHOUT base: 30 to 100 lbs. (13.6 to 45 kg)
WITHOUT BUILTIN HARNESS SYSTEM:
Harness MUST be stored during Booster mode,
see “19.1 Storing Harness, p. 50”.
• Height: 38 to 57 inches (96 and 145 cm)
• Approximately 3-10 years of age
• The shoulder belt MUST lie across child’s shoulder as
shown and the lap portion of the belt is positioned low
on the child’s hips.
• Child’s ears are BELOW top of head support. If tops of ears
are above top of head support, child is too large for booster
seat.
• If child is between 30 and 65 lbs (13.6 and 29.5 kg) and
shoulders are below the upper harness slots, we highly
recommend using in
harness for as long as possible (up to 65 lbs).
forward-facing mode with built-in
7.1 Vehicle Seat Location Requirements
IMPROPER PLACEMENT OF THE CHILD
RESTRAINT INCREASES THE RISK OF
SERIOUS INJURY OR DEATH. Some seating
positions in your vehicle may not be safe for this child restraint. Some
vehicles do not have any seating positions that can be used safely with the
child restraint. If you are not sure where to place the child restraint in your
vehicle, consult your vehicle owner’s manual or call Graco Children’s Products
Inc., at 1-800-345-4109.
• Children are safer when properly
restrained in rear vehicle seating
positions.
Whenever possible secure the child
restraint in the center position of the seat
directly behind the front seats.
However, this position is sometimes
equipped with a lap belt only and cannot
be used when this child restraint is used
without the built-in harness.
7.0 Choosing an Appropriate Vehicle Seat Location
• The vehicle seat must face
forward. Do not use child
restraints on rear-facing or
side-facing vehicle seats.
7.2 Vehicle Seat Belt Requirements
MANY SEAT BELT SYSTEMS ARE NOT SAFE TO USE
WITH THE CHILD RESTRAINT. THE VEHICLE SEAT
BELT MUST BE DESIGNED TO HOLD THE CHILD
RESTRAINT TIGHTLY AT ALL TIMES. DO NOT USE A VEHICLE BELT THAT
CHANGES LENGTH WHILE DRIVING. Pay careful attention to these systems; some
of the seat belts that are not safe to use look very much like seat belts that are safe
to use. If you are unsure, consult your vehicle owner’s manual or call Graco Children’s
Products Inc., at 1-800-345-4109.
7.3 SAFE Vehicle Seat Belt Systems
THE FOLLOWING BELT SYSTEMS CAN BE USED WITH YOUR CHILD RESTRAINT,
IF the seat location meets all other requirements of these instructions and those in
your vehicle owner's manual. LATCH can be used in place of the following vehicle belt
systems if your vehicle is equipped with LATCH anchor points. Please refer to vehicle
owners manual for LATCH locations.
7.4 For Built-in Harness Only
• Lap Belts - Manually adjusted when
buckled, the belt is tightened
manually by pulling on the free end.
• Lap Belts with Automatic Locking
Retractor (ALR) - The automatic locking
retractor will not permit the lap belt to
lengthen once it is buckled. Tighten the
belt by feeding the belt back into the
retractor while pushing down hard on the
child restraint.
7.5 With or Without Built-in Harness
• Combination Lap/Shoulder Belt with
Locking Latch Plate - Once it is buckled, this
type of belt has a latch plate that will not
allow the lap portion of the belt to loosen. Belt
is tightened by pulling hard on the shoulder
portion of the vehicle belt while pushing
down hard on the child restraint.
• Combination Lap/Shoulder
Belt with Sliding Latch Plate -
This belt has a latch plate that
slides freely along the belt.
7.6 UNSAFE Vehicle Belt Systems
DO NOT USE ANY OF THE FOLLOWING SYSTEMS TO SECURE THE CHILD
RESTRAINT. LATCH can be used IN PLACE OF the following unsafe belt systems if
your vehicle is equipped with LATCH anchor points. Please refer to the vehicle owners
manual for LATCH locations. NEVER USE unsafe belt systems.
• Lap Belts with Emergency
Locking Retractor (ELR)
This lap belt stays loose and can
move until it locks in a crash or
sudden stop.
• Combination Lap/Shoulder Belt
with Retractor
Each strap has a retractor at one end
and is attached to the latch plate at
the other end.
• Passive Restraint - Lap or Shoulder
Belt Mounted on Door
• Passive Restraint -
Lap Belt with Motorized Shoulder Belt
DO NOT use vehicle belts that are attached
to the door in any way or that move along a
track to automatically surround the
passenger when the door is closed.
• Lap Belts Forward of Seat Crease
Vehicle seat belts located forward of seat
crease may not securely hold child restraint.
Check vehicle owner’s manual or see vehicle
dealer for car seat installation requirements.
• If approved for use with child restraint,
install child restraint and check for secure
installation by pulling child restraint front
to back. If child restraint slides forward,
DO NOT use these seat belts.
8.1 What is LATCH?
United States Federal Motor Vehicle Safety Standards have defined a new system
for installing child restraints in vehicles. The system is called LATCH.
LATCH stands for: Lower ANchors and Tether for CHildren.
LATCH in the vehicle consists of a top tether anchor point and two lower anchor
points.
Some vehicle owner manuals use the term ISOFIX to identify the new child
restraint anchor system. This child restraint with LATCH can also be used in
vehicle seating positions equipped with ISOFIX.
Newer vehicles have one or more seating positions with LATCH anchor points. If
vehicle is equipped with LATCH, the vehicle lower anchor points may be visible at
the vehicle seat crease. If not visible, they may be marked with this symbol .
CHECK vehicle owner’s manual for vehicle top tether anchor locations. They may
be identified using one of the anchor symbols as shown .
ONLY use LATCH on a child restraint in a seating position recommended by
vehicle manufacturer.
8.0 LATCH
NOTE: Some vehicle manufacturers have lower maximum weight ratings for LATCH
anchors, so you must consult your vehicle owner’s manual or call the
vehicle manufacturer to confirm the limits on your vehicle’s LATCH anchors.
Use vehicle belt (not LATCH connectors) for installations with children weighing
more than 48 pounds (21.7 kg).
See your vehicle owner’s
manual for exact
locations, anchor
identification, and
requirements for use
with a child restraint.
Vehicle
Seat Crease
Vehicle Top Tether
Anchor Points
Vehicle Lower
Anchor Points
Typical seat in a
passenger vehicle.
Other vehicle types
may have different
LATCH locations.
8.2 LATCH System
LATCH consists of a permanently
attached lower anchor belt and a top
tether strap.
ONLY use LATCH in a seating position
recommended by vehicle manufacturer.
LATCH lower vehicle anchor points are
defined as 11 inches from the center of
one LATCH anchor to the center of
another LATCH anchor.
If allowed by your Vehicle Owners
Manual, the center seating position
maybe used if the anchor spacing is 11”
or greater.
REARFACING
Lower Anchor Belt
Vehicle Lower
Anchor Points
Vehicle Top Tether
Anchor Point
Vehicle Lower
Anchor Points
FORWARDFACING
Child Restraint
Top Tether
Lower
Anchor Belt
You must carefully follow the instructions provided by your vehicle manufacturer,
in addition to the information in this manual. Before proceeding be sure you
have read and understood, “7.0 Choosing an Appropriate Vehicle Seat
Location” on pages 22-26.
Make sure vehicle is on level ground A and not like in picture B.
If a front passenger seat is used (see air bag warning, page 4), slide the vehicle
seat rearward as far as possible from the dashboard. If a rear seat is used, make
sure the seat in front of it is moved forward enough and is upright enough to
allow room for the child restraint.
When using the vehicle seat belts to install the base, the lock-off is ALWAYS used
to secure both belts of the lap or lap/shoulder belt.
1. Position base in vehicle seat as shown C.
2. Open the lock-off and route the vehicle belt through the belt path and over
the lock-off D.
3. Buckle seat belt. Pull up on shoulder belt while pushing down on base to
tighten E.
4. Close lock-off F.
5. Test base for secure installation by moving front to back and left to right at the
belt path G. Base should not move more than 1 inch ( 2.54 cm). If belt loosens
or lengthens, repeat procedure.
9.0 Installing Base Using Vehicle Seat Belt
Lap Belt H and Lap/Shoulder Belt I should appear as shown when installed.
A C
Vehicle
Belt
B
D
G
Lap Belt
E
H
F
Lap/Shoulder
Belt
I
1. Remove LATCH from storage area
its maximum length.
2. Place base in vehicle seat as shown B.
3. Make sure LATCH is routed through vehicle/LATCH belt path normally used
for vehicle seat belt.
Belt must lay flat and not be twisted.
4. Hook Connectors to vehicle lower anchors. Pull firmly on Connectors to be
sure they are attached C.
5. NEVER put two LATCH connectors on one vehicle LATCH anchor unless
specifically allowed by the vehicle manufacturer D.
6. With base flat on vehicle seat, slide back until top of base contacts seat back.
Make sure that base bottom remains flat on the vehicle seat E.
7. Tighten LATCH by pushing down hard on the center of the base and pulling
the free end of the adjustment belt F.
8. Test base for secure installation by moving front to back and left to right at
the belt path G. Base should not move more than 1 inch ( 2.54 cm). If belt
loosens or lengthens, repeat procedure.
10.0 Installing Base Using LATCH
9. Check that the LATCH stays tight and does not slip from the tightened
position. If it does not stay tight, try another seating position or contact Graco
at 1-800-345-4109.
10. To remove LATCH lift up on metal tongue of buckle and remove LATCH as
shown H.
A. For ease of installation, extend LATCH
to
A
B C
D
G
H
E
F
1. Test base for secure installation. See sections 9.0 and
10.0 for base installation, p. 30-33
2. Push in B and rotate knobs C on both sides of child
restraint at the same time to unlock position.
3. Place child restraint on base in rear-facing position D.
4. Rotate knobs on both sides of child restraint to lock it
into base E. You will see lock symbols in windows on
side of base as shown H.
5. If you see the red ags up in the child restraint
seating area F and you see the unlock symbol I
then seat is not secured to base.
6. Check seat is secure by moving front to back and left
to right at the belt path G. Base should not move
more than 1 inch ( 2.54 cm). If belt loosens or
lengthens, repeat procedure.
NOTE: Make sure tether is stored. See “14.1 Tether
Storage”, p. 39. You can not use tether in rear-facing
mode.
11.0 REAR-FACING INSTALLATION
NOTE: Bubble in level indicator must be fully
between the two lines J. Level indicator is for
rear-facing use only. See “17.0 Using Recline”, p. 44
A.
A
D
F
CB
J
E
G
LOCKED
H
UNLOCKED
I
1. Test base for secure installation. See sections 9.0 and
10.0 for base installation, p. 30-33
2. Push in B and rotate knobs C on both sides of child
restraint to unlock position.
3. Place on base in forward-facing position D.
4. Rotate knobs on both sides to lock seat to base E.
You will see lock symbols in windows on side of base
as shown H.
5. If you see the red ags up in the child restraint
seating area F and you see the unlock symbol I
then seat is not secured to base.
6. Check seat is secure by moving front to back and left
to right at the belt path G. Base should not move
more than 1 inch ( 2.54 cm). If belt loosens or
lengthens, repeat procedure.
Note: See “13.0 Tether Use”, p. 38 to attach tether.
A.
12.0 FORWARD-FACING INSTALLATION
A
D
F
CB
Tether
E
G
LOCKED
H
UNLOCKED
I
All LATCH seating positions have tether anchors.
Always use tether if a vehicle tether anchor is
available in forward-facing mode with harness. Check
your vehicle owner’s manual for the tether anchor
location(s). If your vehicle is not equipped with a tether
anchor, it may be possible to install one. Contact your
vehicle dealership for the proper anchor location and
installation.
NOTE: TETHER NOT TO BE USED IN
REARFACING MODE.
1. Check that tether is securely attached to child
restraint.
2. Fasten tether clip to anchor point
13.0 TETHER USE
3. Tighten adjustment belt to remove any slack B.
4. To loosen, push button while pulling on the belt
as shown C.
A.
A
B
C
14.1 Tether Storage
Tether must be stored to child restraint for rear-facing
use.
• Store by clipping to bar on back of seat as shown A.
• Pull loose end of adjustment strap to remove any
slack.
• Roll loose end of adjustment strap up and secure with
a rubber band.
14.2 LATCH Storage
• To store LATCH belt insert into LATCH storage
compartment on back of seat
P
D
1
A
5
5
9
0
9
B.
14.0 TETHER AND LATCH STORAGE
A
B
15.1 Harness Straps
• To tighten: Pull harness adjustment strap A.
• To loosen: Lift lever B while pulling shoulder
harness straps C.
Harness Strap
15.2 Chest Clip
• To open: Press tabs and pull apart D.
• To close: Snap halves together E. Make sure
the chest clip is locked by pulling out on each half.
Chest
Clip
Buckle
15.3 Buckle
• To buckle: Insert both tongues into buckle F.
Pull up on tongues to be sure they are locked.
• To unbuckle: Press red button and pull tongues
out of buckle G.
15.0 HARNESS SYSTEM
15.4 Crotch Strap
• Choose the crotch strap position that is closest to but not under your child.
• Push the clip at the end of crotch strap through bottom of seat and pull out
through the seat and seat cover H.
• Reinsert in other crotch strap opening and push through seat cover and seat I.
CHECK buckle is securely installed by pulling up on crotch strap. The clip must
be properly seated.
Crotch
Strap
Harness
Adjustment
Strap
A B C
D E F
Bottom of
Bottom of
child restraint
child restraint
Bottom of
G H I
Bottom of
child restraint
child restraint
16.1 Body Support (on certain models)
To prevent ejection in sudden stop or crash:
• Use in rear-facing mode only.
• Never allow body support to bunch or fold behind child.
1. Make sure chest clip and harness are open.
2. Place body support behind harness as shown in A.
3. Pull crotch strap through matching slot in body support
16.0 ACCESSORIES
and in seat cover B.
A
B
16.2 Harness Covers & Crotch Strap Cover (on certain models)
Crotch Strap Cover
Harness
Cover
To prevent serious head injury in sudden stop or crash:
• Harness covers are not to be used by children over 40 lbs.
• Harness covers must be used in rear-facing mode.
• Always make sure shoulder straps are properly positioned on shoulders.
• Make sure that harness covers do not interfere with placement of the chest clip
at armpit level.
THIS SIDE DOWN
HA
ESTE LADO
CIA ABAJO
CIA ABAJO
ESTE LADO
HA
THIS SIDE DOWN
• Wrap crotch strap cover around
crotch strap and fasten hook and
loop tape at front A.
• Wrap harness covers around the harness straps
with the text “THIS SIDE DOWN” facing the
child’s shoulder.
• Fasten hook and loop tape B.
BA
FAILURE TO PROPERLY recline the infant restraint on
the vehicle seat increases the risk of serious injury or
death.
Recline only works in modes where child restraint is attached to the base.
FORWARDFACINGREARFACING
1. Pull up on recline button on front of
child restraint A.
2. Bubble in level indicator C must be
fully between the two lines D. E is
not level.
3. Vehicle must be on level ground and
child in child restraint when checking
level indicator.
17.0 USING RECLINE
NOTE: Level indicator is for
rear-facing use only.
If using seat with child 40-65lbs,
always use recline position 1.
1. Pull up on recline button on front of
child restraint B.
2. Adjust recline to desired level
indicated on label F on side of
base F.
REAR FACING
FORWARD-FACING
A
C E
B
NOT LEVELNOT LEVEL
D
F
F
18.1 Placing Child in Child Restraint
1. Place child in child restraint
restraint. Avoid bulky clothing.
2. Place harness straps over child’s shoulders and insert tongue(s) into buckle B.
3. Pull up on tongue(s) to be sure they are locked.
4. Close chest clip C:
Position chest clip at arm pit level.
5. Pull on harness adjustment strap to tighten straps as shown D. A snug strap
should not allow any slack. It lies in a relatively straight line without sagging.
It does not press on the child’s esh or push the child’s body into an unnatural
position.
6. SAFETY CHECK :
a) MAKE SURE the top of the child’s head is at least 1” (2.54 cm) below the top
of the infant restraint.
b) CHECK that harness straps are not twisted.
c) CHECK that the harness is snug. You should NOT be able to pinch E the
harness if it is snug. A snug strap should not allow any slack. It lies in a
relatively straight line without sagging. It does not press on the child’s esh
or push the child’s body into an unnatural position.
18.0 SECURING CHILD IN CHILD RESTRAINT
7. A rolled towel can be used on each side to support small children F. Be sure
towels do not interfere with harness system. Towels should NOT be placed
under child.
A with child’s back at against back of child
Chest Clip
Buckle
Harness
adjustment
strap
A B
C D
E F
18.2 Check Harness System
To prevent serious injury or death:
• Keep harness straps snug and positioned on
shoulders with chest clip at arm pit level.
• Do not use strap covers, blankets, cushions, or
padding under harness straps or child unless
provided by Graco.
• Child should be dressed in clothing that does not
interfere with buckling the harness.
REAR-FACING
• 5-40 lbs (2.2-18.1 kg)
Harness straps/head
support must be in
one of the bottom 3
height positions
below the shoulders.
• Harness height must
be below child’s
shoulders.
FORWARDFACING
• 20-65 lbs (9.1-29.5 kg)
and at least one
year old.
Harness straps/
head support must
be in one of the top
4 height positions,
at or above
shoulders.
• Harness height
must be at or just
above child’s
shoulders.
18.3 Adjusting Head Support/
Harness Straps
Failure to properly
adjust the harness
straps for your child
increases the risk of serious injury or death
in the event of a sharp turn, sudden stop or
crash.
• BEFORE adjusting the head support height,
have your child lean forward slightly.
• Squeeze the red adjustment handle
top of seat and pull head support up until it
snaps into one of the 6 height positions.
• To lower, squeeze red adjustment handle
and push head support down.
• CHECK to make sure it is securely snapped
into one of the 6 height positions by pulling
up on head support.
When using in rear-facing mode always use
one of the bottom 3 height positions B.
When using in forward-facing mode always
use one of the top 4 height positions B.
Refer to page 48 for harness strap
placement.
A on
A
B
D
19.1 Storing Harness
Harness must be stored during Booster Mode.
1. Push the clip at the end of crotch strap through bottom of seat and pull out
through the seat and seat cover A.
2. Rotate bottom of head support pad up and attach to back of head support
pad with hook and loop tape B.
3. Disconnect snaps on seat cover
4. Move harness straps behind seat cover D.
5. Disconnect snaps or hook and loop tape (on certain models) and move
shoulder straps behind head support pad E.
6. Open door behind seat cover F.
7. Insert harness buckle and crotch straps into harness storage compartment G.
8. Close door H.
9. Re-attach snaps on seat cover I.
C.
19.0 BOOSTER INSTALLATION
Bottom of
child restraint
A
B C
DE F
G H I
19.2 Using Child Restraint in Booster Mode
Failure to properly secure your child in the child
restraint increases the risk of serious injury or death
in the event of a sharp turn, sudden stop or crash. In
a crash, the child restraint provides NO protection for your child unless the vehicle
lap/shoulder belt is properly secured. Follow these instructions carefully to properly
secure your child.
• Vehicle belts MUST lay at against child and MUST not be twisted.
• NEVER use a vehicle lap-only belt across front of child
• DO NOT use shoulder belt loose or positioned under arm B.
• DO NOT place shoulder belt behind child’s back C.
• Lap portion of lap/shoulder belt MUST be low and snug on hips, just touching
thighs.
• DO NOT allow child to slide down in booster seat D.
• If child will not keep vehicle belt properly positioned, DO NOT use this booster
seat. Use a dierent child restraint system.
• DO NOT position vehicle belt over top of the armrests E.
• Vehicle seat head support should not create a gap between vehicle seat and
booster seat F. The front of booster seat MUST NOT hang over front of vehicle
seat G.
• DO NOT place child in booster if ags are up in the seat area H.
• DO NOT use in Booster mode with base I.
A.
A B C
D E F
G H I
19.3 Securing Child in Booster Seat and Vehicle
USE ONLY the vehicle lap and shoulder belt system
when restraining the child in the booster seat.
1. Remove base from vehicle seat A.
2. Place booster seat firmly against the back of a forward-facing vehicle seat
equipped with a lap/shoulder belt only
3. Place child in booster seat with child’s back flat against back of booster seat.
4. Position lap/shoulder belt through shoulder belt guide C not
underneath shoulder belt guide. Fasten buckle and pull up on the
shoulder belt to tighten. Be sure lap portion of the belt goes under
armrests D.
5. If shoulder belt lays across child’s neck, head or face, redirect shoulder belt
over shoulder by adjusting the head support setting, see “19.4 Adjusting
Head Support in Booster Mode” , p. 56.
6. The shoulder belt MUST lie across child’s shoulders in red zone as shown E.
B.
Shoulder
belt
Armrest
A
Lap belt
B
CDE
19.4 Adjusting Head Support in
Booster Mode
When using in booster mode always use one
of the top 4 height positions A.
• BEFORE adjusting the head support height,
have your child lean forward slightly.
• Squeeze the red adjustment handle
top of seat and pull head support up until it
snaps into one of the 4 height positions.
• To lower, squeeze red adjustment handle
and push head support down.
• CHECK to make sure it is securely snapped
into one of the 4 height positions by pulling
up on head support.
• FOR PROPER FIT: The shoulder belt
guides must be even with or just above
the shoulders C.
B on
A
B
C
20.1 Adjusting Armrest
Armrest can be adjusted by pushing up or
down on it A.
20.0 Additional Information
A
20.2 Removing Seat Cover
1. Store harness see “19.1 Storing
Harness”, p. 50.
2. Remove elastic loops and butterfly
tabs from seat as indicated
in Aand B.
3. Pull off cover taking care
around the lock knobs,
recline handle, level indicator
and cup holder.
4. Machine wash cover in
cold water on delicate cycle
and drip-dry. DO NOT USE
BLEACH.
5. To put the seat cover back
on, reverse preceding
instructions.
Elastic loops
2X
A
Butterfly
tabs
B
20.3 Airplane Use
• This child restraint system conforms to all applicable
Federal Motor Vehicle Safety Standards.
• This Restraint is Certified for Use in Motor Vehicles.
• This Restraint is NOT Certified for Use in Aircraft.
20.4 Care and Maintenance
• Continuous use of child restraint may cause damage to vehicle seat. Use a child
restraint mat, towel or thin blanket to protect upholstery.
• Metal and plastic parts: clean with mild soap and cool water. No bleach or
detergents.
• Harness straps and LATCH straps: spot clean with damp sponge. Do not immerse the
straps in water. Doing so may weaken the straps.
• Buckle should fasten with a “click”, if not, rinse buckle with warm water. DO NOT USE
SOAPS or LUBRICANTS. DO NOT use household detergents. Never lubricate buckle.
• If buckle or harness adjuster sticks or will not remain tight, check for foreign objects
such as food, dirt, etc. Remove objects with tweezers and/or clean with a cotton
swab. If you cannot get the harness to remain tight with the buckle securely locked,
do not use this child restraint.
To purchase parts or accessories or for warranty information in the United
States, please contact us at the following:
www.gracobaby.com
or
1-800-345-4109
Owner’s Manual Storage
21.0 Replacement Parts, Warranty, and
Store instruction manual in the space
provided on back of seat.
ALL-IN-ONE CARSEATALL-IN-ONE CARSEAT
Loading...