Graco FinishPro HVLP 7.0, FinishPro HVLP 9.0, FinishPro HVLP 9.5 Operation - Repair - Parts

Operation, Repair, Parts

FinishPro™ HVLP 7.0/9.0/9.5

For portable spray applications of fine finish coatings. For professional use only. Not
approved for use in European explosive atmosphere locations.

313406J

120 Vac Models: 256847, 256848, 256849
240 Vac Models: 256851, 256852, 256853

Maximum Working Pressure: 10 psi (0,07 MPa, 0.7 bar)

Important Safety Instructions

Read all warnings and instructions in this
manual. Save these instructions.

US Patent No.: 7,950,598, 7,971,806

EN

ti12834a

Table of Contents

Table of Contents

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Grounding and Electric Requirements . . . . . . . . 5

Component Identification . . . . . . . . . . . . . . . . . . . . 6

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Fluid Preparation . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connect Fluid and Air Supply . . . . . . . . . . . . . . . 7

Pressure Relief Procedure . . . . . . . . . . . . . . . . . 7

Operation Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Sprayer Disassembly . . . . . . . . . . . . . . . . . . . . 10

Sprayer Assembly . . . . . . . . . . . . . . . . . . . . . . . 10

Motor Replacement . . . . . . . . . . . . . . . . . . . . . . . . 11

Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Models 256847, 256848, 256849, 256851, 256852,

256853 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Models 256847, 256848, 256849, 256851, 256852,

256853 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Parts Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 18

2 313406J

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation
point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. Refer back to
these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applica­ble.

WARNING

GROUNDING

This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric current. This product is equipped with a cord hav­ing a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is
properly installed and grounded in accordance with all local codes and ordinances.

• Improper installation of the grounding plug is able to result in a risk of electric shock.

• When repair or replacement of the cord or plug is required, do not connect the grounding wire to either flat blade
terminal.

• The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.

• Check with a qualified electrician or serviceman when the grounding instructions are not completely understood,
or when in doubt as to whether the product is properly grounded.

• Do not modify the plug provided; if it does not fit the outlet, have the proper outlet installed by a qualified electri­cian.

• This product is for use on a nominal 120V circuit and has a grounding plug similar to the plug illustrated in the fig­ure below.

• Only connect the product to an outlet having the same configuration as the plug.

• Do not use an adapter with this product.

Extension Cords:

• Use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that accepts the plug
on the product.

• Make sure your extension cord is not damaged. If an extension cord is necessary, use 12 AWG

(2.5 mm

• An undersized cord results in a drop in line voltage and loss of power and overheating.

313406J 3

2

) minimum to carry the current that the product draws.

Warnings

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explo­sion:

• Do not spray flammable or combustible materials near an open flame or sources of ignition such as cigarettes,
motors, and electrical equipment.

• Paint or solvent flowing through the equipment is able to result in static electricity. Static electricity creates a risk of
fire or explosion in the presence of paint or solvent fumes. All parts of the spray system, including the pump, hose
assembly, spray gun, and objects in and around the spray area shall be properly grounded to protect against static
discharge and sparks. Use Graco conductive or grounded high-pressure airless paint sprayer hoses.

• Verify that all containers and collection systems are grounded to prevent static discharge.

• Connect to a grounded outlet and use grounded extensions cords. Do not use a 3-to-2 adapter.

• Do not use a paint or a solvent containing halogenated hydrocarbons.

• Keep spray area well-ventilated. Keep a good supply of fresh air moving through the area. Keep pump assembly in
a well ventilated area. Do not spray pump assembly.

• Do not smoke in the spray area.

• Do not operate light switches, engines, or similar spark producing products in the spray area.

• Keep area clean and free of paint or solvent containers, rags, and other flammable materials.

• Know the contents of the paints and solvents being sprayed. Read all Material Safety Data Sheets (MSDS) and
container labels provided with the paints and solvents. Follow the paint and solvents manufacturer’s safety instruc­tions.

• Fire extinguisher equipment shall be present and working.

• Sprayer generates sparks. When flammable liquid is used in or near the sprayer or for flushing or cleaning, keep
sprayer at least 20 feet (6 m) away from explosive vapors.

ELECTRIC SHOCK HAZARD

Improper grounding, setup, or usage of the system can cause electric shock.

• Turn off and disconnect power cord before servicing equipment.

• Use only grounded electrical outlets.

• Use only 3-wire extension cords.

• Ensure ground prongs are intact on sprayer and extension cords.

• Do not expose to rain. Store indoors.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

• Read MSDS’s to know the specific hazards of the fluids you are using.

• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Always wear appropriate gloves, eye protection, and a respirator or mask when painting.

• Do not operate or spray near children. Keep children away from equipment at all times.

• Do not overreach or stand on an unstable support. Keep effective footing and balance at all times.

• Stay alert and watch what you are doing.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not kink or over-bend the hose.

• Do not expose the hose to temperatures or to pressures in excess of those specified by Graco.

• Do not use the hose as a strength member to pull or lift the equipment.

PRESSURIZED ALUMINUM PARTS HAZARD

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such
solvents in pressurized aluminum equipment. Such use can cause serious chemical reaction and equipment rupture,
and result in death, serious injury, and property damage.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equip­ment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This
equipment includes but is not limited to:

• Protective eyewear and hearing protection

• Gloves, clothing and respirator as recommended by the fluid and solvent manufacturer

4 313406J

Grounding and Electric Requirements

Warnings

This equipment requires a 120 Vac, 60 Hz, 15A circuit,
with a grounding receptacle.

Do not alter the ground prong or use an adapter.

Sprayer Components Table

Sprayer Model Hose Gun Fluid Sets

FinishPro 7.0

FinishPro 9.0

FinishPro 9.5

256847, 256851 30-ft 256855 EDGE #3

256848, 256852 30-ft 256855 EDGE #3, #4

256849, 256853 30-ft and 4-ft 256855 EDGE #2, #3, #4

Use 3-wire, 12 awg, 50 ft (15 m) or shorter, extension
cords with ground prong.

313406J 5

Component Identification

Component Identification

G

E

L

M

U

N

A

B

H

Item Description

Sprayer air outlet HVLP connector for air sup-

A

Sprayer power

B

switch

Fluid storage

C

compartment

ply to HVLP spray Gun

On/Off switch for sprayer
motor

Provides storage for up to
four fluid sets

Sprayer handle Folds flat for minimum stor-

D

Power

E

cord storage

Air filters (pre-fil-

F

ter and main)

Spray gun

G

age space

Provides storage for power
cord

Provides filtered air for spray
gun and motor

Graco EDGE
with EasyGlide

™

spray gun

™

trigger

Air filter indicator Lights when air filter needs to

H

Connector and
power cord

J

be cleaned or replaced

Provides power for sprayer
(power cord provided with
sprayer)

ST

R

D

K

F

P

C

J

ti12858a

Item Description

Resettable circuit

K

breaker

Quick

L

connect

Provides protection for motor

Enables quick connection to
spray gun

Air valve Provides FinishPro 9.0 and

9.5 sprayers ability to shut off

M

air to spray gun

Air hose Hose, 30 ft x 1 in., that con-

N

nects spray gun and sprayer.

Hose wrap Provides storage for air hose

P

Storage tray Provides extra storage

R

Cleaning cup

S

holder

EDGE spray gun

T

holder

when air hose is not in use

Provides storage for cleaning
cup

Provides external storage for
spray gun

Hose, 4-ft Allows increased flexibility for

U

the FinishPro 9.5

6 313406J

Setup

Fluid Preparation

Setup

• Strain fluids before you spray. This includes color,
reducers and hardeners.

• Use a slower drying reducer or thinner to compen­sate for the faster drying time caused by the warm air
of the turbine. Do not over reduce

• Sprayer performance varies with the viscosity of the
material sprayed and the length of the hose. To pre­vent pressure drop, use hose supplied with sprayer.

• Most material manufacturers provide recommenda­tions for their materials. Follow these recommenda­tions.

Connect Fluid and Air Supply

Spray Gun with Siphon Cup

1. Connect air hose to sprayer.
Hand tighten.

ti13082a

Pressure Relief Procedure

The spray gun siphon cup is pressurized by the gun
air supply. To reduce the risk of serious injury from
pressurized fluid or accidental spray from gun, always
turn off the air supply to the spray gun before remov­ing the siphon cup.

1. Turn off sprayer.

2. Unplug sprayer.

3. Unlatch cup cover; loosen or remove cup from cover
to relieve pressure.

Operation Tips

2. Connect air hose from sprayer to
inlet fitting of gun.

ti12797a

3. Fill cup 3/4 full. Install cover. Latch
the gun cup cover to secure it to
siphon cup. See HVLP EDGE Gun
manual 313317 for operation
instructions.

ti12872a

Connect to Electric Supply

Plug sprayer power cord into grounded outlet. Grounding
and Electric Requirements, page 5.

Sparks can be expected during normal operation of
motor. These sparks can ignite fumes from flammable
liquids, dust particles, and other flammable sub­stances in the spray area.

• Use additional hose if necessary, and ensure the
sprayer is operated in clean, dry, well ventilated
area.

• Never use sprayer inside spray booth.

• Turn sprayer on a few minutes before spraying to
allow warm-up.

• Ensure sprayer filter is clean before operating. Clean
filter, page 8.

• To adjust spray gun pattern, see HVLP EDGE Gun
manual 313317.

• To get proper adhesion, ensure surface is completely
clean.

• Always spray with the least amount of pressure
required to provide the desired spray pattern and rate
of application. Spraying at pressures higher than nec­essary wastes paint and can result in an orange peel
finish.

313406J 7

Maintenance

Maintenance

The sprayer system is lifetime lubricated. The only main­tenance required is filter cleaning and replacement.

Filter Operation

The sprayer filter must be clean at all times to provide suf­ficient air flow to cool the motor and atomize the fluid.

The sprayer has an air filter indicator light on the front
panel. The indicator light illuminates if the filter is clogged
or has low airflow.

8049a

Cleaning Filter

• Tap filter gently on flat surface, dirty side down.

• Direct, compressed air (100 psi(7 bar, 70 MPa)
maximum) through filter panel in the opposite
direction of arrows on side of filter (from the clean
side to the dirty side.

• Soak filter for 15 minutes in water and mild deter­gent. Rinse filter until clean. Air dry.

To avoid electric shock, never install a damp filter in the
turbine. Installing a damp filter in sprayer can also
damage turbine.

1. Turn off and unplug sprayer.

2. Loosen four screws (18), remove filter retainer (17)
and pre-filter (20).

3. Remove main filter (21) and clean using one of the
following methods:

21

20

17

18

ti13061a

8 313406J

Troubleshooting

Troubleshooting

Problem Cause Solution

No fluid delivery No material, no remote cup pressur-

ization, hose or pickup tube clogged

Sprayer not starting No power Check outlet for power. Cycle red

Poor atomization Dirty filter Clean filter and replace as necessary.

Extension cord too long Extension cord must be 3-wire, 12

Hose too long Replace with shorter hose. See

Circuit breaker trips Filter clogged Clean filter and replace as necessary

High ambient temperature Move sprayer to cooler area.

Excessive current draw Return to authorized service center.

Check cup for material

Check for leaks at the container gas­ket (1-quart remote cup cover).
Tighten cover if loose.

Check air flow (approximately 1/4
CFM) from male quick-disconnect at
Compact outlet.

Turn pressure regulator clockwise.
Look for pressure on gauge. (If no
pressure on gauge, check air line fit­tings.)

Check hole in 1-quart remote cup
cover at needle valve for blockage or
dirt. Clean if necessary.

Check for obstructions.

Check if fluid pickup tube is loose.
Tighten.

Blow out and clear material hose.

Clean check valve. See manual
313317

rocker switch.

Check that correct IEC (modular)
cord is used and plugged in.

Check circuit breaker (38). Push to
reset.

AWG, 50 ft (15 m) or shorter.

Graco Fine Finish Solutions brochure
300564, for hose part numbers.

313406J 9

Repair

Repair

Sprayer Disassembly

To avoid injury, including electric shock turn off sprayer
and unplug power cord before performing any repair
procedures on the turbine.

1. Remove four thumbscrews (18) and remove filter
retainer (17), prefilter (20) and main filter (16). Parts,
page 14.

18

3. Place sprayer upside down. Remove four screws (77)
from sprayer base plate (2).

77

2

ti12973a

4. Pull up sprayer base plate and attached parts.
Thread motor wires that connected to inlet plug
through access in HVLP box.

5. Repair or replace any required parts.

Sprayer Assembly

16

20

17

2. Remove two screws (45) and inlet plug (36) from
HVLP box (1). Remove four motor wire connectors
from inlet plug (36).

36

45

ti13062a

ti13061a

ti13063a

1. Thread motor wires that connected to inlet plug
through access in HVLP box. Insert sprayer base
plate and attached parts down into HVLP box.

2. Install four screws (77) into sprayer base plate (2).

3. Install three motor wire connectors onto inlet plug
(36). Install inlet plug (36) with two screws (45) into
HVLP box (1).

4. Remove four thumbscrews (18) and Install filter gas­kets (19), main filter (16), prefilter (20) and filter
retainer (17) with four thumbscrews (18).

10 313406J

Motor Replacement

Motor Replacement

Refer to Parts Drawing, page 14.

1. Follow Sprayer Disassembly procedure, page 10.

2. Remove gasket (25).

3. Remove three screws (6).

4. Remove plate (82) and three spacers (83).

5. Remove motor wires from spade connectors.

6. Rotate motor (24) from outlet fitting (18) and lift up

from spacers (23).

7. Install new gaskets (21, 23, 24, 59 and 60).

8. Reassemble motor.

9. Connect ground wire to motor housing.

10. Reconnect wires.

313406J 11

Wiring Diagrams

Wiring Diagrams

USA

GROUND

12

7

3

4

N

L

G

1

Ref Part Description Qty

1 244273 Conductor, BK 1
2 15W486 Conductor, BK 1
3 15W485 Conductor, G/Y 1
4 15W484 Conductor, W 1
5 257333 Conductor, W, BK, G 1

8

G

BK

W

2

9

6 240256 Conductor, W 1
7 114064 Plug, inlet 1
8 114403 Circuit Breaker, 15A 1
9 15V923 Plug, outlet, CompPack 1
10 114280 Light, indicator, 120V 1

L

11 114293 Switch, rocker 1

G
N

12 114279 Sensor, pressure 1

6

11

3

2
5

6

5

10

ti12765a

International

GROUND

15

8

6

7

10

3

4

N

L

G

1

Ref Part Description Qty

1 244273 Conductor, BK 1
2 15W486 Conductor, BK 1
3 15W485 Conductor, G/Y 1
4 15W484 Conductor, W 1
5 257333 Conductor, W, BK, G 1

11

6 15W488 Conductor, W 1

BK

G

W

2

12

7 15W487 Conductor, BK 1
8 240558 Conductor, G/Y 1
9 240256 Conductor, W 1
10 114064 Plug, inlet 1

L

11 16A348 Circuit Breaker, 10A 1

16

G

12 15V923 Plug, outlet, CompPack 1

N

13 114286 Light, Indicator, 240V 1
14 114293 Switch, rocker 1
15 114279 Sensor, pressure 1
16 116168 Filter, suppression 1

5

ti12770a

3
6

LG

LINE

L2

L1

G

LOAD

L2

2
5

14

9

13

12 313406J

Technical Data

120 Vac, 60 Hz

Ampere Watts

Maximum

Hose Length

ft (m)

Sprayer Weight

lb (kg)

Total Weight

lb (kg)

Sound
Power*

Technical Data

Sound

Pressure*

FinishPro 7.0

FinishPro 9.0

FinishPro 9.5

240 Vac, 50 Hz

FinishPro 7.0

FinishPro 9.0

FinishPro 9.5

* Sound Power and Sound Pressure are measured at
1 meter per ISO 3744

11.0 200 40 (12,2) 28 (12,7) 38 (17,2) 94.9 dBa 82 dBa

11.0 250 60 (18,3) 29 (13,2) 39 (17,7) 95.9 dBa 83 dBa

13.6 300 60 (18,3) 30 (13,6) 40 (18,1) 96.3 dBa 83.4 dBa

Maximum

Hose Length

Ampere Watts

5,40 200 40 (12,2) 28 (12,7) 38 (17,2) 94.9 dBa 82 dBa

5,93 250 60 (18,3) 29 (13,2) 39 (17,7) 95.9 dBa 83 dBa

7,07 300 60 (18,3) 30 (13,6) 40 (18,1) 96.3 dBa 83.4 dBa

ft (m)

Sprayer Weight

lb (kg)

Total Weight

lb (kg)

Sound

Power*

Sound

Pressure*

313406J 13

Parts

Models 256847, 256848, 256849, 256851, 256852, 256853

Parts

4

103

3

6

30

8

1

102

34

100

30

63

62

33

104

105

49

89

13

87

25

77

88

61

101

77

19

16

18

20

17

18

35

ti12835a

14 313406J

Parts List

Models 256847, 256848, 256849, 256851, 256852, 256853

Parts List

Ref Part Description Qty

1 277934 BOX, HVLP 1
3 24B055 COVER, HVLP, includes 6 1
4 15V791 HANDLE 1
6 15V771 LID, accessory 1
8 15V926 LATCH 2
13 257159 HOSE, air, 30 ft, black 1
16 240273 FILTER, main 1
17 15W794 RETAINER, filter 1
18 15W897 SCREW, captive 4
19 15W217 GASKET, filter 2
20 15W909 FILTER, foam 1
25 113817 BUMPER 4
30 15W505 SCREW, mach, phillips pan hd 2
33 256855 GUN, HVLP, with cup 1
34 114271 STRAP, retaining 1
35 15V862 HOSE, rack 1
49 VALVE, air control

FinishPro 7.0 (not included)
240065 FinishPro 9.0 1
240065 FinishPro 9.5 1

Ref Part Description Qty

61 15V923 PLUG, inlet 1
62 ▲ 15W100 LABEL, safety 1
63 ▲ 15W223 LABEL, safety 1
77 15W359 SCREW, mach, hex, washer hd 8
87 15W635 LABEL, FinishPro, HVLP 1
88 LABEL, FinishPro, HVLP

15W636 LABEL, FinishPro, HVLP 7.0 1
15W637 LABEL, FinishPro, HVLP 9.0 1

15W638 LABEL, FinishPro, HVLP 9.5 1
89 257161 HOSE, 4 ft, FinishPro 9.5 1
100 15V927 HINGE 2
101 117317 SCREW, plastite, pan hd 2
102 15X227 SCREW, cap, hex hd 2
103 102040 NUT, lock, hex 2
104 116234 BOTTLE 1
105 M70402 QUICK DISCONNECT 1

▲ Extra Danger and Warning labels are available for free.

313406J 15

Parts Drawing

Models 256847, 256848, 256849, 256851, 256852, 256853

Parts Drawing

29

14

38

9

48

24

41

5

59

31

90

21

15

11

109

107

108, 111

30

58

110

27

86

28

106

45

39

14

22

60

44

42

23

37

56

2

64

45

36

46

45

32

ti12836c

16 313406J

Parts List

Models 256847, 256848, 256849, 256851, 256852, 256853

Parts List

Ref Part Description Qty

2 257066 PLATE, base, turbine, painted 1
5 114279 SENSOR, pressure 1
9 156698 O-RING 1
11 TURBINE* +

15Y812 FinishPro 7.0, 3-stage, 120V 1
15Y813 FinishPro 9.0, 4-stage, 120V 1
15Y814 FinishPro 9.5, 5-stage, 120V 1
15Y815 FinishPro 7.0, 3-stage, 240V 1
15Y816 FinishPro 9.0, 4-stage, 240V 1

15Y817 FinishPro 9.5, 5-stage, 240V 1
14 114670 SCREW, cap, hex hd 6
15 194094 PLATE, turbine 1
21 GASKET, turbine

15W153 FinishPro 7.0 1

15W152 FinishPro 9.0 1

192788 FinishPro 9.5 1
22 15W274 DUCT, turbine 1
23 192846 GASKET, DUCT 1
24 192845 GASKET, DUCT 1
27 114293 SWITCH, rocker 1
28 LIGHT, indicator

114280 120V 1

114286 240V 1
29 15W272 FITTING, outlet 1
30 114669 SCREW, mach, phillips pan hd 2
31 193059 GASKET, sensor 1
32 CIRCUIT Breaker

114403 120V, 15A 1

16A348 240V, 10A 1
36 114064 PLUG, INLET 1
37 192905 PLATE, deflector 1
38 SPACER, turbine

15W148 FinishPro 7.0 3

15W149 FinishPro 9.0 3

Ref Part Description Qty

15W150 FinishPro 9.5 3
39 192810 HOSE, air 1
41 192780 SPACER, turbine 3
42 111593 SCREW, grounding 1
44 102063 WASHER, lock, ext 1
45 SCREW, mach, torx pan hd

15W998 120V 4

15W998 240V 6
46 CORD, power

15W126 USA, 6 ft. 15A, 120V 1

116281 Euro, 2 m, 8A, 240V 1
48 114287 FITTING, barbed 1
56 186620 LABEL, ground 1
58 ▲ 15K616 LABEL, brand, hot surface 1
59 16E351 GASKET, duct, left 1
60 16E353 GASKET, duct, right 1
64 ▲ 15W224 LABEL, safety 1
86 15W640 LABEL, brand, TurboForce 1
90 114689 BUSHING, strain relief 1
106 116168 FILTER, suppression, EMI, 240V 1
107 242001 CORDSET, adapter, Europe 1
108 287121 CORDSET, adapter, 220V, global,

includes 108a through 108d
108a CORDSET, adapter, Italy 1
108b CORDSET, adapter, Denmark 1
108c CORDSET, adapter, Switzerland 1
109 195551 RETAINER, plug adapter 1
110 15X254 SWITCH INDICATOR 1
111 242005 CORDSET, adapter, Australia 1

* Cleaning Brush Kits 256953 and 256954 are also available.

▲

Extra Danger and Warning labels are available for free.

+

Turbine kit includes items 9, 15, 21, 23, 24, 59 and 60

1

313406J 17

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material
and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by
Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco
component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures,
accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures,
accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the
claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the
original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made
at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY
GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their

manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the
furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of
Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de
ou en rapport, directement ou indirectement, avec les procédures concernées.

ADDITIONAL WARRANTY COVERAGE

Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment Warranty Program”.

Graco Information

For the latest information about Graco products, visit www.graco.com.

TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2008, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 313406

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

www.graco.com

Revised 09/2011