Failure to follow these warnings and the assembly
instructions could result in serious injury or death.
This device is designed only to monitor the sounds of your child. It will not alert you to your child’s silent activities.
When using the monitor, you must still provide the supervision necessary for the continued safety of your child. This product
is not designed or intended for use as a medical monitor. Always be sure that both the transmitter and receiver are working
properly and are within range of each other.
• STRANGULATION HAZARD. Keep the AC adapter cords out of the reach of children. Do not use with extension cords.
• DO NOT place the Nursery Units or their cords within your child’s reach. Do not put the Nursery Units inside a crib or play
yard.
• Use ONLY with 110-120 volt AC electrical outlets.
• Protect the AC adapter cords. Place them so they are not walked on or pinched by furniture or other items.
• Allow for proper ventilation when units are in use. Do not cover the Nursery Units or Parent Units with any object such
as a blanket. Do not place them in a drawer or in any location which would muffle the sound or interfere with the normal flow of
air.
• DO NOT immerse any part of the Nursery Units, Parent Units, or Docking Stations in water. Clean only with a dry cloth.
• DO NOT place the Nursery Units near water and moisture. Do not use the Nursery Units outdoors. Do not use the Nursery
Units near possible wet areas, such as a bathtub, shower, wash basin, sink, laundry tub, swimming pool, wet basement, etc.
• Keep Nursery Units away from heat sources, such as fireplaces, radiators, stoves, and TVs or other appliances. Heat can
damage the case or electrical parts.
• DO NOT use the Nursery Units if:
• The AC adapter cords or plugs have been damaged.
• The units have been exposed to liquids.
• The units have been dropped or are damaged.
• DO NOT OPEN THE NURSERY UNITS, PARENT UNITS, DOCKING STATIONS OR ADAPTERS. No user-serviceable parts
inside. Risk of electrical shock, fire or death.
• The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.9”) from all persons
and must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Statement:
WARNING Modifications not authorized by the manufacturer may void users authority to operate this device.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Graco Children’s Products
2794
150 Oaklands Blvd.
Exton, PA 19341
1-800-345-4109
2
Battery Installation
Parent Unit
• The battery must be plugged into the Parent Unit before the
unit will be ready for use. Remove the battery door cover on the
Parent Unit with a key or flat blade screw driver. Remove the battery
pack from the packaging and plug into the back of the unit. Place
he battery pack into the recess and press the wire into the slot on
t
the side. Replace the battery door.
Nursery Unit
• Turn the unit over, and use screw driver to remove the battery door.
• Place 3-AAA (1.5V-LR03) batteries into the battery compartment. Note
the proper orientation of the batteries.
• Place the battery door back on the unit and fasten the screw.
• Please remove a dead battery promptly. A dead battery left in the unit
may leak, damaging your unit.
• Do not attempt to recharge a non-rechargeable battery.
• A rechargeable battery CANNOT be recharged by plugging the AC
adapter into the Nursery Unit.
• Remove the batteries from the unit if it is no longer being used or will
be stored for an extended period of time.
Plug in cord
+
+
-
Batteries should be disposed of properly
by recycling.
-
+
Using AC Adapters
• The Parent Unit can use either the rechargeable battery that comes with the unit or standard 120 volt AC household
current. The Nursery Unit uses 3-AAA (1.5V-LR03) batteries or standard 120 volt AC household current.
• To use AC adapters, plug the connector on the cord into the AC adapter jack on the side of the Parent Unit (under the
rubber cover) or the back of the Nursery Unit. If using the Docking Station, plug the AC adapter connector into the back of the
Docking Station. The Parent Unit may now be placed in the Docking Station. Then plug the adapter into a standard wall outlet.
• Use ONLY the Graco adapters included with the unit. Do not use these adapters with other equipment under any
circumstances.
• If units do not work, check that AC adapters are plugged into working outlets.
• When electricity is off (from a power failure, etc.), the Nursery Unit will operate on 3-AAA (1.5V-LR03) batteries. If the Power
LED is not lit, turn the power off and then back on to the Nursery Unit. A green LED indicates that the batteries are fine. A red
LED indicates that the batteries are low. If the LED does not light at all, then replace the batteries. The Parent Unit will operate
if the rechargeable battery is charged.
Selecting Channels
• In case you are experiencing some interference, the channel on the Nursery Unit can be changed by pressing the Channel
Button (labelled “ch”) on the side of the unit. The Parent Unit will automatically scan all of the available channels until it
locks on to the Nursery Unit. If you are still experiencing interference, press the Channel Button on the side of the Nursery
Unit up to 3 times until a good channel is found.
3
Low Battery Indication
Parent Unit
• When the battery is low in the Parent Unit, the LED bar on the side of the unit will change from green to red and you will hear a
series of 3 audible beeps every 5 seconds. If operated too long on a low battery, you may also experience a poor signal and the
loss connection LED on the front of the Parent Unit will illuminate red and you will begin to hear a continuous audible beep from
the Parent Unit.
•You may either turn off the unit, plug in the A/C adapter or place the unit in the docking station to recharge the batteries.
Nursery Unit
• When the battery is low in the Child Unit, the LED on the front of the unit will change from green to red. If operated too long
on a low battery, you may also experience a poor signal from one or both of the Nursery Units. Under this circumstance, the
loss connection LED (red) on the front of the Parent Unit may illuminate when the corresponding Nursery Unit is active and you
will begin to hear a continuous audible beep from the Parent Unit.
• You may either plug in the A/C adapter or replace the batteries.
Out of Range Indicator
• If the Parent Unit begins to lose signal from one or both of the Nursery Units, the loss connection LED (red) will illuminate
when the corresponding Nursery Unit is active. Additionally, a continuous audible beep will be generated to warn the user that
the connection to the Nursery Unit(s) has been lost.
• Immediately move the Parent Unit closer to the Nursery Unit(s) to regain connection.
• Once connection has been re-gained, the Loss Connection LED will turn off and the audible beep will stop.
***Note: It is not uncommon for the Parent Unit to occasionally lose and regain connection with the Nursery
Unit in environments that have a significant amount of obstructions.
First Time Use
***NOTE: It is very important that the steps below be followed for first time power-up.
1. For optimum operation, it is best to charge the batteries in the Parent Units for at least 16 hours prior to use. The rechargeable
batteries need to be installed into the Parent Unit before charging - refer to the “Battery Installation” section. DO NOT turn on
power while the unit is charging for the first time.
2. Place the Nursery Units in two different rooms, and within 10 feet (3 meters) of each child. Plug an AC Adapter into the jack on
the back of each Nursery Unit. Plug the AC Adapters into working 120 volt AC outlets.
3. Aim the Nursery Units toward each child. Check that there are no walls or large objects that could block sound transmission.
4. Turn on the Parent Units using the On/Off Button on the side of the units.
5. Turn on the Nursery Units using the On/Off Button on the side. The green power light should come on.
6. The Parent Units will scan every channel to find the Nursery Units and within a few seconds, the Parent Units will find the
Nursery Units and the red Loss Connection LED will turn off. Your monitor is now ready for use.
Testing the System
It is VERY IMPORTANT to test the system when first set up, and at regular times thereafter. Test the units if you
suspect they may have been damaged or have not been used for a long time.
1. If two adults are present, have one take the Parent Units to different locations, trying various volume settings, while the
other speaks into the Nursery Unit.
2. If only one adult is available, place a ticking clock, radio, or other sound-producing device near the Nursery Unit to test it.
3. When testing, keep the level of your child’s sounds in mind, and adjust the volume accordingly.
4. If there is sound interference, press the Channel Button on the Nursery Unit to select another channel.
4
To Listen to Baby
• Turn on Nursery Unit using the On/Off Switch.
• Turn on one or both Parent Units using the On/Off Switch.
• The Sound Lights on the Parent Unit will illuminate as your child (or other objects) make noise near the Nursery Unit. Please
note that the Sound Lights and volume control on the Parent Unit are independent of each other. With the volume turned all
the way down, the Sound Lights will still illuminate as your child (or other objects) make noise near the Nursery Unit.
Changing the Volume
•The volume for each Nursery Unit is adjusted separately.
•Set the Room Select Switch to 1 or 2, to select Nursery Unit 1 or Nursery Unit 2.
•Adjust the volume of the selected Nursery Unit by pressing the Volume Up/Down Buttons.
•The Sound Lights illuminate as the volume button is pressed up or down to provide visual feedback of the volume level.
•The unit will beep louder or softer depending on the selected volume level.
•When no volume button has been pressed for two seconds, the unit will beep three times to indicate that the volume setting
has been stored. The unit will return to normal monitoring.
Changing the Monitoring Time
•The time the Parent Unit monitors each Nursery
Unit is adjusted separately.
•Set the Room Unit Select Switch to 1 or 2, to
select Nursery Unit 1 or Nursery Unit 2.
•Press and hold the Time Adjust button.
•Adjust the time by pressing the Volume
Up/Down Buttons.
•The Sound Lights illuminate as the volume button is pressed up or down to show the selected
time as shown.
•Release the Time Adjust Button. The unit will
beep three times to indicate that the time setting
has been stored. The unit will return to normal
monitoring.
•Only one Nursery Unit can be set to Off at a
time.
Orange
Sound Lights
for Nursery
Unit 1
2 min
1 min
30 sec
10 s ec
OFF
Red Loss Connection LED
Green
Sound Lights
for Nursery
Unit 2
5
Loading...
+ 10 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.