Page 1
Stroller
OWNERS
MANUAL
Model No.
Serial No.
Dear Customer,
Please fill in the
model and serial
numbers above
from the label on
the rear leg of
your new stroller.
Models 7585 and 7587
Congratulations on your purchase of a
®
Graco
Graco
has helped thousands of parents transport
their children in comfort. We believe your
new Graco
promising many hours of enjoyment for
your baby.
Before using your stroller, please take a
few minutes to read this Owners Manual.
The short time you spend reading these
instructions will help you assemble and use
your stroller properly.
stroller!
®
is a world leader in strollers and
®
stroller is a wise choice,
Never leave child unattended.
Always keep your child in view.
Never use stroller on stairs or escalators.
You may suddenly lose control of the
stroller or your child may fall out. Also,
use extra care when going up or down
a step or curb.
Avoid serious injury from falling
or sliding out. Always use seat
belt.
Be certain the stroller is fully erected
and latched before allowing your
child near the stroller.
Please save your Owners Manual
for future use.
Customer Satisfaction
Our goal is to make every product the best it can be!
We are also committed to supporting our products
after purchase. If you would like to speak
to Graco about your product, please contact our
Customer Service Department at 1-800-345-4109.
Our knowledgeable staff will be ready to answer
any questions you may have concerning parts, use
or maintenance. When you call, please have the
model and serial numbers ready so your call may
be processed quickly and efficiently.
© 1998 Graco 808-9-98
Use of the stroller with a child weighing more than 40 lbs. (18.1 kg) will
cause excessive wear and stress on
the stroller. Use the stroller with only
one child at a time.
234
Child may slip into leg openings and strangle. Never
use in reclined carriage position unless footrest is
completely raised and locked into position as shown.
DO NOT lift stroller by the arm bar.
DO NOT use seat in an automobile.
DO NOT use as a car bed.
DO NOT lift, reverse or carry the seat while child is in the seat.
DO NOT add extra mattress padding to the seat that will reduce the depth of seat
to less than 6.75 inches (170 mm).
To prevent a hazardous condition, do not place more than 10 lbs. (4.5 kg) in the
storage basket.
Stroller to be used only at walking speed. Product not intended for use while
jogging, skating, etc.
Discontinue using your stroller should it become damaged or broken.
Page 2
Failure to follow these warnings and the assembly
instructions could result in serious injury or death.
Avoid serious injury from falling
or sliding out. Always use seat
belt.
Never place child in the stroller
with head near the footrest, when
footrest faces forward as shown.
DO NOT place purses, shopping
bags, parcels and accessory items
on handle or canopy. They may fall
on the child, or change the balance
of the stroller and make it unstable.
Never allow your stroller to be
used as a toy.
Avoid strangulation. DO NOT
place items with a string around
your childs neck, suspend
strings from this product, or
attach strings to toys.
Push bar
down to lock
FOR ADDITIONAL IMPORTANT
INFORMATION, please see the
Helpful Hints and Care and
Maintenance sections in these
instructions.
Page 3
PARTS LIST
CHECK that you have all the parts listed below
BEFORE assembling your stroller.
If any parts are missing, call Customer Service
at 1-800-345-4109.
THIS PRODUCT REQUIRES ADULT ASSEMBLY.
No tools required for assembly.
Frame
Rear wheel (2)
Retainer
(2, 1 extra)
Seat
Cap
(2, 1 extra)
To Assemble Front Wheels
To prevent
serious injury or death
from choking, remove and
IMMEDIATELY discard plastic
end caps on the front leg pins.
Step 1.
Remove and discard the plastic
end caps on the front leg
pins. Line up pin with a wheel
assembly as shown.
Plastic snap inside wheel
mount must be away from pin.
Push wheel assembly onto pin
until it snaps into place.
Step 2.
Repeat for other wheel assembly.
NOTE: Pull firmly on each wheel assembly to be
sure the wheel assemblies are securely attached.
End cap
To Assemble Rear Wheels
Place one rear wheel, red retainer, and white cap on one end
of rear axle in order as shown below. Push red retainer onto
axle BEFORE attaching white cap. Repeat on other side.
Front wheel
Rear axle assembly
Boot
(on certain models)
assembly (2)
Canopy
To Unpack Stroller
Step 1.
Flatten stroller carton to protect floor. Slide seat out
from frame and set it aside.
Step 2.
Open stroller frame
on carton by lifting
handle until locking
latches on both sides
are locked as shown.
Locking
latch
To Assemble Rear Axle
Brake levers
point toward
you
Rear legs
Step 1.
Turn stroller over as pictured above.
Step 2.
Position rear axle assembly as shown.
Step 3.
Start both brackets onto leg tubes at the same time.
Step 4.
Push both brackets on until plastic tabs snap into the slots
on the legs.
Step 5.
Be sure cap is snapped securely over red retainer.
To Attach Seat
Step 1.
Set the stroller frame upright.
Step 2.
Line up notches on sides of seat with plastic brackets on
frame. Lower seat onto frame until it snaps into brackets.
Seat can be installed facing either direction. Pull up on
each side of seat to be sure it is securely attached.
Step 3.
To remove seat to reverse position
or for cleaning, squeeze the levers
on both sides of seat and lift.
808-9-98
Pull firmly on each bracket to be sure the brackets are
securely attached.
5
6 87
while child is in the seat.
Page 4
To Assemble Rear Wheels
To Adjust Back
Place one rear wheel, red retainer, and white cap on one end
of rear axle in order as shown below. Push red retainer onto
axle BEFORE attaching white cap. Repeat on other side.
Wheel
Spokes
toward
inside
Rear
axle
Snap red retainer into axle
groove. Then snap cap
over red retainer as shown.
Cap (white)
Attach AFTER
retainer is on axle
Retainer (red)
Wide end
toward wheel
To raise or recline seat back,
pull up the plastic handle at
back of seat and adjust seat
back to desired position.
Seat back can adjust to five
different positions.
To Assemble Canopy
Step 1.
Position canopy over back
of stroller frame as shown.
Align the ends of the canopy
mounts with the openings in
the seat covering. Push the
canopy mounts into the slots
until they snap in place.
Be sure cap is snapped securely over red retainer.
To Attach Seat
Step 1.
Set the stroller frame upright.
Step 2.
Line up notches on sides of seat with plastic brackets on
frame. Lower seat onto frame until it snaps into brackets.
Seat can be installed facing either direction. Pull up on
each side of seat to be sure it is securely attached.
OR
Step 3.
Step 2.
To remove canopy, push in
the button hidden under
the padding directly under
one canopy mount, and
pull the canopy mount out
of the slot. Repeat on other
side.
Button under
padding below
canopy mount
To Adjust Canopy
Push or pull canopy to desired
position.
To remove seat to reverse position
or for cleaning, squeeze the levers
on both sides of seat and lift.
DO NOT lift, reverse or carry the seat
while child is in the seat.
Page 5
To Adjust Arm Bar
Step 1.
To release the arm bar,
squeeze the latches under
the arm bar on both sides
as shown.
Step 2.
Pull arm bar out until it clicks
into extended position.
To Change to Swivel
or Non-swivel Wheels
Front swivel wheels lock for use on uneven surfaces such
as grass, stones or gravel.
Before locking swivels, first push stroller forward a few
feet to ensure that the wheels are correctly positioned.
Slide DOWN for swivel. Slide UP for non-swivel.
To Use Boot (on certain models)
Step 1.
Put seat back into any position
except fully reclined. (For fully
reclined carriage position, see
below.) Set footrest at seat
height and snap arm bar into the
extended position. CHECK that
footrest is secure at seat height
by pressing down on it. If not,
adjust metal bar under footrest.
Place boot under the footrest.
Slide it over footrest and arm bar
as shown.
To Adjust Footrest
Step 1.
To lower the footrest, first lift
the footrest slightly, then pull
down the metal bar as
shown.
Step 2.
To raise footrest to seat height, lift up the metal bar.
Step 3.
If seat is being used in the fully reclined carriage
postion, you must close off the leg opening.
To Use Brakes
Always apply brakes when parking
stroller.
Push brake levers DOWN
to park.
Lift brake levers UP to stroll.
To Secure Your Child
Avoid serious injury from falling or
sliding out. Always use seat belt.
Step 2.
Fasten snaps at top and bottom
corners of the boot to padding at
each side.
If seat is being used in fully reclined carriage position,
close off leg opening as described in To Adjust
Footrest before placing boot on stroller.
To Remove Seat Covering
Seat covering may be removed for washing.
Child may slip into leg openings and
strangle. Never use in reclined carriage position
unless footrest is completely raised and locked into
position as shown.
To close off leg opening:
With arm bar extended, raise
footrest completely and
push footrest bar down
to lock it in place. Then snap
arm bar into normal (nonextended) position. Arm bar
must SNAP into position, not
just press against footrest.
808-9-98
Arm bar IN
Footrest
LOCKED
9
Step 1.
Place crotch strap between legs
and fasten both belt buckles
together.
Step 2.
Adjust belt at both buckles as needed to get a snug fit
around your child.
Step 3.
Squeeze sides of buckles to
release.
10 11 12
Step 1.
Turn seat upside down. Unsnap VELCRO
to release side flaps. Unsnap two snaps at bottom of seat
back and release elastic straps from bar.
Step 2.
Unfasten webbing strap from D
rings under the seat.
Page 6
To Use Boot (on certain models)
Step 1.
Put seat back into any position
except fully reclined. (For fully
reclined carriage position, see
below.) Set footrest at seat
height and snap arm bar into the
extended position. CHECK that
footrest is secure at seat height
by pressing down on it. If not,
adjust metal bar under footrest.
Place boot under the footrest.
Slide it over footrest and arm bar
as shown.
Step 2.
Fasten snaps at top and bottom
corners of the boot to padding at
each side.
If seat is being used in fully reclined carriage position,
close off leg opening as described in To Adjust
Footrest before placing boot on stroller.
Step 3.
Unhook the small elastic loops from the two plastic tabs
found under the footrest.
Step 4.
Turn seat right side up. Put footrest down. Remove arm
bar. (See To Adjust Arm Bar instructions.)
Step 5.
Unbuckle the seat belt. Carefully remove covering from
seat frame. Please note to:
!
Pull crotch strap out of slot in covering.
!
Pull webbing strap and D rings out of slots in the
!
seat frame.
Step 6.
Crotch strap may also be removed for washing. Under
the seat frame, push the plastic crotch strap retainer
through the slot in the frame to remove it.
To Remove Seat Covering
Seat covering may be removed for washing.
Snaps
Step 1.
Turn seat upside down. Unsnap VELCRO®at sides of the seat
to release side flaps. Unsnap two snaps at bottom of seat
back and release elastic straps from bar.
To Reattach Seat Covering
To reattach the seat covering, reverse the previous steps.
Step 1.
Slide back part of covering
over rear of seat frame. Be
sure back part of covering
slides behind, not over, the
side panels of the seat.
Step 2.
Replace all straps:
!
Push webbing strap and
!
D rings through slots in
!
the seat frame as shown.
!
If needed, reattach crotch
!
strap by pushing lower
!
plastic crotch strap retainer
!
through slot in seat frame.
!
Push crotch strap through
!
slot in seat covering.
Fit covering behind
side panels
Step 2.
Unfasten webbing strap from D
rings under the seat.
Step 3.
Fit sides of covering over side panels of seat. Push
covering down into seat.
Page 7
Step 4.
Step 2.
Reattach arm bar. Squeeze both latches below arm bar
holes at sides of seat, and insert bar. Push bar in until it
snaps in place.
Step 5.
Turn seat upside down. Reattach elastic loops on footrest
pad to plastic tabs under footrest.
Step 6.
Thread end of webbing strap
through D rings at back of
seat exactly as shown.
Step 7.
Snap the two elastic straps at bottom of seat back
around the bar. Fasten the side flaps with VELCRO®tabs.
Pull up locking latches at sides
of stroller to release handle,
and fold handle down.
OR
On some models with a one-hand fold, slide red button on
handle, twist grip toward yourself until it stops, then push
handle down on stroller.
1
2
3
Be sure to secure all snaps, VELCRO®, straps and
fabric before using stroller. Pull firmly on waist belt
and crotch strap to make sure they are correctly
attached.
Be sure fabric does not cover notches in seat sides.
Notches must be clear of fabric to securely latch
onto frame.
Keep fabric
out of notches
To Fold Stroller
Step 1.
Before folding stroller, fold
canopy and fully recline seat.
Apply brakes to prevent
stroller from moving.
Step 3.
Close and lock storage latch.
The stroller will fold most
compactly if seat is installed
in the forward-facing position.
808-9-98
13
14 15 16
Page 8
Replacement Parts
HELPFUL HINTS
IF WHEEL SQUEAKS,
use a light oil (e.g., WD-40,
3-in-1, or sewing machine
oil). It is important to get the
oil into the axle and wheel
assembly as illustrated.
WHEN USING YOUR STROLLER AT THE
BEACH, completely clean your stroller after-
ward to remove sand and salt from wheel
assemblies and all mechanisms, including the
bottom of the seat. Sand in the seat latching
mechanism could damage it.
CARE AND MAINTENANCE
TO WASH SEAT COVERING, remove seat
from stroller and remove seat covering.
Machine wash in lukewarm water on delicate
cycle and drip-dry. NO BLEACH.
REMOVABLE SECOND SEAT PAD (if so
equipped) may be machine washed in lukewarm water on delicate cycle and drip-dried.
NO BLEACH.
TO WASH CANOPY:
(1) Remove canopy from
stroller. (2) Unsnap canopy
from plastic canopy mounts.
(3) Unscrew metal support
rod at one end as shown.
(4) Pull end of rod out of
plastic mount. (5) Slide
canopy over plastic mount
and both rods to remove.
Machine wash in lukewarm
water on delicate cycle and
drip-dry. NO BLEACH.
TO CLEAN STROLLER FRAME, use only
household soap or detergent and warm water.
NO BLEACH.
FROM TIME TO TIME CHECK YOUR
STROLLER for loose screws, worn parts, torn
material or stitching. Replace or repair the parts
as needed. Use only Graco
parts.
EXCESSIVE EXPOSURE TO SUN OR HEAT
could cause fading or warping of parts.
IF STROLLER BECOMES WET, open canopy
and remove boot. Allow to dry thoroughly
before storing.
®
replacement
Instructions for ordering stroller parts:
Complete form below. Your stroller model number
MUST be included on the form to ensure proper
replacement parts. Your model number can be found
on a sticker on the rear leg of your stroller.
Payment must accompany your order.
Parts List:
Seat ...................................
Canopy ..............................
Front wheel assembly .......
Price:*
$25.00
$18.00
$16.00
(2 wheels per unit)
Rear axle assembly ..........
Rear wheel ........................
Basket ...............................
Boot ...................................
Arm bar .............................
Removable soft pad**........
Rear wheel hardware ........
** On certain models only
$ 11.00
$ 8.00 (each)
$16.00
$15.00
$15.00
$16.00
No charge
* Prices subject to change without notice.
IF YOU NEED HELP
If you have any questions, please call toll-free:
1-800-345-4109
Return the form below with payment to:
GRACO CHILDRENS PRODUCTS INC.
CUSTOMER SERVICE DEPARTMENT
P.O. BOX 100, MAIN STREET
ELVERSON, PA 19520
Model Number
(Must be filled in)
Seat
Canopy
Front wheel assembly
Rear axle assembly
Rear wheel
Basket
Boot
Arm bar
Removable soft pad
Rear wheel hardware
Total:
Shipping
& handling: $5.00
6% sales tax
(PA only):
Total amount
due:
SHIP TO:
Name
Address
City, State, Zip
( )
Telephone
Check enclosed
(payable to Graco
Childrens Products Inc.)
Charge to credit card:
Visa
MasterCard
Discover
Account #:
Expiration date:
Signature:
Loading...