Graco 700N Instructions Manual

Download

Page 1

INSTRUCTIONS 307–452

Rev. G

INSTRUCTIONS

This manual contains important warnings and information. READ AND RETAIN FOR REFERENCE

Supersedes F

Model

700N

STAINLESS STEEL FLUID PASSAGES

Air

100 psi (7 bar) Maximum Working Fluid Pressure 100 psi (7 bar) Maximum Working Air Pressure

See spray gun ordering numbers and descriptions.

Spray Gun

the charts on pages 4 and 5 for complete air

Table

Warnings 2. Ordering Installation 6 Operation 8 Maintenance 9 Troubleshooting 10 Service 12 Parts 14 Air

Flow Charts Dimensional Technical Accessories 19 Warranty 20 Graco T

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Charts4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Data

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

oll-Free Phone Numbers

of Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Drawing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . .

GRACO INC. P.O. BOX 1441

COPYRIGHT

16.

18.

20.

MINNEAPOLIS, MN

1980, GRACO INC.



55440–1441

Page 2

Symbols

Warning Symbol

WARNING

his

symbol alerts you to the possibility of serious

injury or death if you do not follow the instructions.

WARNING

EQUIPMENT MISUSE HAZARD

INSTRUCTIONS

Equipment

This equipment is for professional use only Read all instruction manuals, tags, and labels before operating the equipment.

Use the equipment only for its intended purpose. If you are not sure, call Graco T tance at 1–800–543–0339.

Do not alter or modify this equipment.

misuse can cause the equipment to rupture or malfunction and result in serious injury

Caution Symbol

CAUTION

This

symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions.

echnical Assis

Check equipment daily

Do not exceed the maximum working pressure of the lowest rated component in your system. This equipment has a

maximum working air pressure.

Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the

nical Data

Methylene Chloride with formic or propionic acid is not recommended as a flushing or cleaning solvent with this gun or any other device with nylon or aluminum components as it can damage these parts.

Hearing protection is recommended when using this equipment.

Read and follow the fluid and solvent manufacturer’s literature regarding the use of protective eyewear

Handle hoses carefully

Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not ex pose Graco hoses to temperatures above 82_C (180_F) or below –40_C (–40

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

, gloves, clothing, respirator and other equipment.

. Repair or replace worn or damaged parts immediately

100 psi (7 bar) maximum working fluid pressure and a 100 psi (7 bar)

. Do not pull on hoses to move equipment.

_F).

Tech-

2 307–452

Page 3

WARNING

PRESSURIZED EQUIPMENT HAZARD

Spray

from the gun, hose leaks, or ruptured components can splash fluid in the eyes or on the skin

and cause serious injury

Do not stop or deflect fluid leaks with your hand, body

Follow the pressure; stop spraying; clean, check, or service the equipment; or install or clean the fluid nozzle.

D T

ighten all the fluid connections before operating the equipment.

Check the hoses, tubes, and couplings daily Permanently coupled hoses cannot be repaired; replace the entire hose.

Pressure Relief Procedure

, glove, or rag.

on page 8 whenever you: are instructed to relieve the

. Replace worn, damaged, or loose parts immediately

3307–452

Page 4

Ordering

Charts

The

charts below provide a cross reference between identification numbers stamped on the parts and the Graco part number assemblies available, grouped by basic gun type. Chart 2 shows fluid nozzle/needle combinations. Chart 3 shows the air caps available.

The following is an example of how to use these charts:

D Y

our application calls for a

Chart 1

shows this to be a

. Chart 1 shows the complete gun

pressure feed gun

P700N basic gun

Chart 1: Gun Combinations Available

P700N: Pressure Feed Guns

Combinations:

Ordering

Part No.

217–750 P700N 0N 0 217–752 P700N 0N 03

Gun Nozzle

See Chart 2

Air Cap

See Chart 3

D Y

our application calls for a

Chart 1

Using

cosity call for an

bination

By using is best for the application.

This makes your combination a

Chart 1

combination is

S700N:

Ordering

Part No.

217–755 S700N 11N 11 217–756 S700N 21N 2

217–758 S700N 3N 3

shows this to be a

Chart 2

Siphon Feed Guns

, the flow rate required and fluid vis

03N fluid nozzle and needle

Chart 3

shows that the

, you determine that the

217–752

Combinations:

Gun Nozzle

pressure feed gun

P700N basic gun

P700N–03N–0

Graco part number

See Chart 2

See Chart 3

com-

0 air cap

for this

Air Cap

Terms:

Light Fluid:

enamel primers.

Medium Fluid:

epoxies, vinyls, high flow – high viscosity

Heavy Fluid:

19 to 24 seconds (No. 2 Zahn cup). Auto, furniture, appliances, fine-finish metallics, top coats, lacquer

22 to 41 seconds (No. 2 Zahn cup). Contact adhesive, latex, maintenance paints, textures, primers,

Mastics, block fillers, roof coating, sound deadeners, adhesive, textures.

4 307–452

Page 5

Ordering

Patt

Ord

Charts

Chart 2: Fluid Nozzle/Needle Combinations*

ype

Nozzle/

Needle

Orifice

Size

ow Rate

fl oz/min

(liters/min)

Recommended Usage

(see TERMS above)

Order Part Number

Kit

Nozzle Only

Needle Only

0N/0N 0.047”

(1.2 mm)

11N/2N 0.055”

(1.4 mm)

21N/2N 0.070”

(1.8 mm)

3N/3N 0.098”

(2.5 mm)

* Needles and fluid nozzles are manufactured in matched, lapped sets and should be ordered as a kit to ensure per

fect seating of the needle in the fluid nozzle.

{ Optional

(1.4 mm) orifice size. T

NOTE:

Chart

Type

Plastic Tipped Needle, Part No. 108–704

See page 17 for

Fluid Flow Charts.

3: Air Caps A

ern Leng

at 10 in.

(254 mm)

8–18

(0.24–0.54)

4–10

(0.12–0.30)

8–12

(0.24–0.36)

12–18

(0.36–0.54)

ypical use is for extremely light viscosity fluids, such as stains and dyes.

Light fluid

Pressure feed

Light fluid

Siphon feed

Medium fluid

Siphon feed

Heavy fluid

Siphon feed

, can

106–766 106–750 106–758{

106–768 106–751 106–759{

106–769 106–752 106–760

106–770 106–753 106–761

 be

used with 0.047 in. (1.2 mm) and 0.055 in.

vailable

Recommended

Pattern Shape

Recommended Usage

Consumption

cfm at ps

(m#/min

at bar)

Nozzle

0 11 21 3

Part

Number

0 13–16”

(330–400 mm)

03 9–13”

(230–330 mm)

11 8–10”

(200–250 mm)

2 9–11”

(230–280 mm)

3 11–13”

(280–330 mm)

NOTE:

See page 16 for

Long taper duction. Lacquers, acrylics, epoxies.

Medium taper production. Lacquers, acrylics.

Blunt end. Low to medium pro duction. Lacquers, enamels.

Blunt end. Medium production. Lacquers, enamels.

apered. Medium to high produc

tion. Heavy fluids.

Air Flow Charts

. Medium to high pro

. Medium to high

15 at 50

(0.42 at 3.5)

16 at 50

(0.44 at 3.5)

12 at 50

(0.34 at 3.5)

1 at 50

(0.31 at 3.5)

12 at 50

(0.34 at 3.5)

X 106–700

X 106–706

X 106–702

X 106–703

X 106–705

5307–452

Page 6

Installation

Fig. 1

Pressure Feed Model Shown

KEY

EF G H

A Model B C D E F G H

700N Spray Gun Fluid Inlet; 3/8 npsm Air Inlet; 1/4 npsm Air Hose Air Shut-of Air Regulator Air Filter Air Supply Line

f V

alve

04835

Ventilate the Spray Booth

WARNING

TOXIC

FLUID HAZARD

o prevent hazardous concentrations of toxic and/or flammable vapors, spray only in a properly ventilated spray booth.

Never operate the spray gun unless ventilation fans are operating.

Check and follow all of the national, state and local codes regarding air exhaust velocity requirements.

Check and follow all local safety and fire codes.

Installation Procedure

NOTE:

recommended accessories.

See

Accessories

section for information on

Install an air filter (G) in the gun air supply line to ensure a clean dry air supply to the gun. See Fig. 1. Dirt and moisture in the air line can af

fect

the appearance of your finished workpiece.

Install an air regulator (F) downstream from the air filter to control atomizing air pressure to the gun.

Install an air shut-of

Connect the atomizing air hose (D) to the 1/4 npsm

f valve (E).

air inlet (C) of the gun.

Connect the fluid supply hose, siphon cup gravity cup (see Fig. 2) to the 3/8 npsm fluid inlet (B) of the gun.

NOTE:

If you use a fluid supply line, install a fluid regu lator in the gun fluid supply line to control fluid pressure to the gun.

6 307–452

Page 7

Installation

NOTE:

On the gravity gun,

gravity cups connect to the

gun at a fluid inlet on the side of the gun. See Fig. 2.

KEY A Gravity

Cup

Gravity Gun Fluid Inlet 3/8 npsm

Fig. 2

04837

7307–452

Page 8

Operation

Pressure Relief Procedure

WARNING

PRESSURIZED

The system pressure must be manually relieved to prevent the system from starting or spraying acci dentally. T dental spray from the gun, splashing fluid, or mov ing parts, follow the whenever you:

are instructed to relieve the pressure,

stop spraying,

check or service any of the system equipment,

or install or clean the spray nozzles.

1. T

urn of

f the air and fluid supply to the gun.

2. T

rigger the gun into a grounded metal waste con

tainer to relieve system pressures.

Filter the Fluid

Strain

or filter the fluid to remove coarse particles and sediment, then check the viscosity of the fluid. Install the proper needle/nozzle set and air cap combination selected from the charts on page 5.

EQUIPMENT HAZARD

o reduce the risk of an injury from acci

Pressure Relief Procedure

NOTE:

way

Hold the gun about 10 in. (254 mm) away from the sur face of the test piece. Adjust the air pressure to the gun until proper atomization is achieved. Use the low est possible air pressure to obtain the desired results.

NOTE:

to regulate air at the gun.

Continuous Spraying

Leave the fan and fluid adjustment valves in the full open positions. This provides maximum fluid flow and prevents premature wear on the fluid nozzle. Use sep arate regulators to control the air and fluid flow to the gun.

Short-term Operations

The pattern size and fluid output volume may be re duced by turning in the fan and fluid adjustment valves.

Spray Pattern Direction

If the fluid adjustment knob is turned in all the

, the gun will emit only air

est the Spray Pattern

The air adjustment valve (17) can also be used

WARNING

Adjusting the Spray Pattern (See Fig. 3)

The

desired pattern, volume of fluid output and degree of atomization can easily be obtained by regulating the fan adjustment valve (5) and the fluid adjustment knob (6).

Adjust the Pattern Size

urn the fan adjustment valve (5) out (counterclock

wise) to make the spray pattern wider

Adjust the Fluid Output V

urn the fluid adjustment knob (6) out all the way (counterclockwise). Then adjust the air pressure at the pressure feed tank until the desired fluid flow is ob tained. For the final adjustment, turn the fluid adjust ment knob in (clockwise) to reduce the volume of fluid output until the desired results are obtained.

Adjust the Fluid Output V Gravity Feed

urn the fluid adjustment knob (6) in (clockwise) to reduce the volume of fluid output, and turn it out (coun terclockwise) to increase the fluid output.

olume for Pressure Feed

olume for Siphon or

o reduce the risk of serious injury whenever you

are instructed to relieve pressure, always follow the

Pressure Relief Procedure

The direction of the spray pattern is determined by the position of the air cap (3). The horns of the air cap should be the opposite direction (horizontal or vertical) of the desired direction of the spray pattern. T the spray pattern direction, first Then loosen and turn the air cap to the desired position and hand tighten the air cap securely

Proper pattern adjustment will give a spray pattern shaped like this:

Vertical Pattern

See

the

Troubleshooting Chart

lution of improper spray patterns.

at left.

relieve the pressure

Horizontal Pattern

for the cause and so

o change

8 307–452

Page 9

Maintenance

CAUTION

o avoid contaminating the fluid being sprayed, be sure that the solvents used are compatible with the fluid being sprayed.

o avoid getting solvent in the gun air passages, never immerse the gun in solvent.

CAUTION

Methylene Chloride with formic or propionic acid is

not

recommended as a flushing or cleaning solvent with this gun or any other device with nylon or alu minum components, as it can damage these parts.

Relieve the pressure.

Wipe the outside of the gun clean with a solvent dampened cloth.

If the air cap and fluid nozzle need cleaning,

lieve the pressure

from the gun. Remove the fluid nozzle with the special nozzle wrench (21), supplied. Soak the fluid nozzle in solvent and wipe it with a clean cloth. Soak the air cap in solvent and scrub it with a fine bristled brush (20). T air cap, use a toothpick or other soft implement to avoid damaging critical surfaces.

, and remove the air cap (3)

o clean the holes in the

re-

CAUTION

Cleaning

WARNING

o reduce the risk of serious injury whenever you

are instructed to relieve pressure, always follow the

Pressure Relief Procedure

1. T

o clean the gun, flush it with a compatible solvent until all traces of paint are removed from the gun passages.

on page 8.

Never use metal instruments to clean holes in the air cap and nozzle. Metal instruments can damage the holes in the air cap and fluid nozzle, resulting in distortion of the spray pattern.

Lubricating

Lubricate the gun daily with light oil at the points marked

needle spring (7) with lightweight grease or petroleum jelly.

in Fig. 3. Periodically lubricate the fluid



9307–452

Page 10

Troubleshooting

WARNING

o reduce the risk of serious injury whenever you

are instructed to relieve pressure, always follow the

Pressure Relief Procedure

Relieve the pressure before you check or service any system equipment.

on page 8.

Check all possible causes and solutions in the

Troubleshooting Chart

before disassembling the

gun.

NOTE:

Some improper patterns are caused by the

improper balance between air and fluid.

Problem:

Improper Spray Pattern

Fluttering or spitting spray

Cause Solution

Insufficient

Loose fluid nozzle or damaged fluid nozzle taper seat.

Dirt between fluid nozzle, taper seat, and body

Loose or cracked fluid inlet fitting (22). Loose fluid tube in cup or tank. Dry or worn fluid needle packing or

loose packing nut permits air to get into fluid passage (siphon feed).

Fluid build-up on air cap; partially clogged horn holes. Full air pressure from clean horn hole forces fan pattern toward clogged end.

Damaged fluid nozzle or air cap holes.

Fluid build-up on the perimeter of fluid nozzle orifice, or partially clogged fluid nozzle orifice.

oo high atomization air pressure.

fluid supply

Adjust fluid regulator or fill fluid supply T

ighten fluid nozzle or replace fluid

nozzle and needle. Clean.

ighten or replace fitting.

T Tighten. Lubricate or replace packings (10);

tighten packing nut (9).

Clean with soft implement or sub merge in suitable solvent and wipe clean.

Replace damaged part.

Remove obstruction. Never use wire or hard instruments.

Reduce air pressure or adjust fan ad justment valve (5).

Fluid too thin. Not enough fluid pressure.

Low atomization air pressure.

Fluid too thick. T

Streaks

Last coat of fluid applied too wet. T Insuf Non-uniform spray pattern.

10 307–452

oo much fluid.

oo much air pressure.

ficient air pressure.

Regulate fluid viscosity Increase fluid pressure.

Increase air pressure or adjust air ad justment valve (17).

Regulate fluid viscosity

On siphon feed guns

by adjusting fluid adjustment knob (6).

On pressure feed guns

pressure. Adjust fluid adjustment knob (6) until proper pattern is obtained.

Apply drier finish with multiple strokes. Use lowest air pressure necessary. Increase air pressure. Clean or replace air cap.

, reduce fluid flow

, reduce fluid

Page 11

Problem Cause Solution

Fluid packing nut leaking.

Air leakage from front of gun. Fluid leakage from front of gun.

Troubleshooting

Loose needle packing nut (9). W

orn needle packings (10). Air valve (12, 13) not seating properly Needle (1) worn or damaged. W

orn needle and nozzle seat in fluid nozzle (2).

Needle packings (10) too tight.

. Clean, service.

Tighten. Replace.

Replace. Replace fluid nozzle and needle.

Lubricate packings (10) and adjust packing nut (9).

11307–452

Page 12

Service

WARNING

reduce the risk of serious injury whenever you

are instructed to relieve pressure, always follow the

Pressure Relief Procedure

Relieve the pressure before you check or service any

system equipment.

NOTE:

spring (1 spring (1 into the fluid valve cavity

The fluid needle spring (7) and the air valve

1) are not interchangeable. The air valve

1) is slightly larger in diameter and will not fit

Air Valve Service

1. If

there is air leakage at the air valve needle (12), remove the trigger and unscrew the air valve as sembly

. See Fig. 3.

on page 8.

. See Fig. 3.

Fluid Packing Replacement

1. If

leakage occurs at the fluid needle packing nut (9), tighten the nut. If leakage does not stop, re move the fluid adjusting valve knob (6), spring (7) and needle (1). See Fig. 3.

Unscrew the packing nut (9) and remove the old packings (10). A small hooked tool can be used to remove packings from the cavity spect all the parts for wear or damage, replacing parts as needed.

Lubricate the new packings and the needle with lightweight oil and insert the packings into the cav ity in the order shown in Fig. 3, Detail D.

Install the needle (1). Slide the packing nut (9) onto the needle before inserting the needle into the packing cavity fluid adjusting knob (6) into the gun body

5. T

urn the fluid adjusting knob (6) in until it bottoms out, then back it out six full turns for proper spring adjustment.

. Then install the spring (7) and the

. Clean and in

Clean and inspect the needle (12), spring (1 air valve (13) for wear or damage. Replace if needed.

Apply a few drops of light-weight machine oil to the

3. air valve needle (12) and reassemble the air valve.

1) and

With the trigger released, screw the packing nut (9) in until the packings are fully compressed, then back it of gun is triggered.

NOTE:

daily as explained in

f until the needle moves freely when the

For the best fluid packing life, lubricate the gun

Maintenance.

12 307–452

Page 13

Service

Installing Fluid and Air Fittings

the fluid fitting (22) is removed, be sure to install its gasket and washer when reinstalling the fitting. Apply Loctiter threads and torque it into the gun body to 20 ft-lb (27 N

242 sealant or equivalent on the fluid fitting

Sm).

If the air fitting (23) is removed, apply Loctiter PST pipe sealant or equivalent to its threads and screw it into the gun body

Apply

Loctiter 242 sealant or equivalent on

threads and torque to 20 ft-lb (27 N.m).

See Detail D.

Lubricate daily with light oil.

urn counterclockwise to widen spray pattern.

urn clockwise to narrow spray pattern.

urn counterclockwise to increase fluid output.

urn clockwise to decrease fluid output.

Apply Loctiter PST pipe sealant or equivalent on threads.

1312

DETAIL D

Fig. 3

13307–452

Page 14

Model 700N

Includes items 1–23

Parts

*10

11*

12*

18*

19*

13n

19*

17n

04868

14 307–452

Page 15

Parts

Ref. No. Part

1 2 3 4 106–785 BODY 5 106–719 VAL

6 105–553 7* 105–554 8 106–720 9 106–718 NUT 10* 106–885 KIT 11* 105–608 12* 106–731 VAL

No.

Description Qty.

NEEDLE, fluid See charts on page 5 NOZZLE, fluid See charts on page 5 AIR CAP See charts on page 5

Includes fittings 22 & 23

VE, fan adjustment KNOB, fluid adjustment SPRING, compression, fluid needle GUIDE, needle, fluid

, packing, needle

SPRING, compression, air valve

VE, air (needle)

, gun

Ref. No.

13n 106–732 KIT

14 106–730 TRIGGER 1 15 105–606 SCREW

16 105–605 SCREW 17n 106–729 VAL

18* 105–551 GASKET 1 19* 105–563 O-RING 2

21 179–764

22 106–786 1 1

23 106–784 1

1 1

Part No.

Description Qty.

, packing, air valve

, pivot, trigger , retaining, trigger

VE, air adjustment

BRUSH; not sold separately WRENCH, nozzle FITTING, fluid; includes gasket & washer FITTING, air 1

Keep these spare parts on hand to reduce down

time.

These parts are included in Repair Kit 106–779, which may be purchased separately

1 1

15307–452

Page 16

Air

Flow Charts

Each chart is headed by a gun model number. The first number

refers to the 700N gun series. The next number refers to the fluid nozzle. The last number refers to the air cap.

To use the Charts:

1. Find

the chart corresponding to your need.

(Gun Model – Nozzle – Air Cap)

Model 700N–0N–0, 700N–0N–03

Part No. 217–750, 217–752

Air Flow

(SCFM)

20 15

5 0

0 1020304050607080

Air Pressure (psig)

2. On

the horizontal axis, note the air

used.

pressure that will

3. Go up vertically until you intersect the actual flow line.

4. Go

across and read the flow in cfm.

Model 700N–11N–11

Part

No. 217–755

16 14 12

Air Flow

(SCFM)

8 6 4 2 0

0 1020 3040 5060 7080

Air Pressure (psig)

Air Flow

(SCFM)

Model 700N–21N–2

Part

No. 217–756

14 12 10

8 6

4 2

0 10 20304050 607080

Air Pressure (psig)

16 307–452

Page 17

Air Flow

(SCFM)

Air

Flow Charts

(Gun Model – Nozzle – Air Cap)

Model 700N–3N–3

Part No. 217–758

010203040506070 80

Air

Pressure (psig)

Pressure

FluidFlow

(cc/min)

1600 1400 1200

1000

800 600

400 200

Feed Fluid Flow Charts

(Gun Model – Nozzle)

Model 700N–0N

Nozzle

0 5 10 15 20 25 30 35 40 45 50

Part No. 106–750

Fluid Pressure (psi)

♦ Low Viscosity = 18 Sec. #2 Zahn Cup

Medium Viscosity = 30 Sec. #2 Zahn Cup High Viscosity = 30 Sec. #3 Zahn Cup

17307–452

Page 18

Dimensional

Drawing

Reference

A 6.22 in. (158 mm) B C D

Maximum Maximum Weight 20 Wetted Maxiumum Noise Sound pressure Sound power

working fluid pressure working air pressure

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

parts

data*

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

working temperature

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .



. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Technical

SST

, leather and PTFE or polyethylene and polyester elastomer

Data

Dimension

3/8 npsm fluid inlet

7.13 in. (181 mm) 1/4 npsm air inlet

100 psi (7 bar) 100 psi (7 bar)

104_F (40_C).

oz (557 g)

87.0 Db(A)

99.7 Db(A)

All readings were taken with the gun controls fully open with an air inlet pressure of 65 psi (4.5 bar). Sound pres

sure was tested to CAGI-PNUEROP – 1969. Sound power was tested to ISO 3744 – 1981.

Manual

The

manual was revised to include the following changes:

The maximum working pressure was changed to 100 psi.

CE symbol was added to the front page.

D T

ext and warnings were updated for CE requirements.

Change Summary

18 307–452

Page 19

Accessories

Use Only Genuine Graco Parts and Accessories

Air

Atomizing Hose, Buna-N

200 psi (14 bar) Maximum Working Pressure

5/16 in. (7.9 mm) ID; coupled 1/4 npsm(f) swivel both ends; neoprene cover

210–866 210–867 210–868

Fluid Supply Hose, Nylon

300 psi (21 bar) Maximum Working Pressure

3/8 in. (9.5 mm) ID; cpld 3/8 npsm(f) swivel both ends; neoprene cover

205–160 205–142 205–143

15 ft (4.7 m) long 25 ft (7.6 m) long 50 ft (15.2 m) long

Throat Seal Liquid (TSL) 206–995

1 quart (0.97 liter) non-evaporation lubricant for air and fluid packings.

Siphon Cup PC–12 105–700

34 oz. (1000 cc) capacity; 3/8 npsm(f)

Replacement diaphragm available. Order part number 106–776.

Replacement lid gasket available. Gasket is polyethylene. Order part number 106–778.

04836

COUPLER

STEMS

3/8 npsm

Models

GUN

MOUNTED

FLUID

REGULATORS

1/4 npsm inlet &

return ports

5 to 35 psi

(0.5 to 2.5 bar)

Regulated

Pressure

Models

STRAIGHT

ADAPTERS

3/8 npsm inlet

TWIST LOCK SLIP RING UNION

ADAPTER

223–627*

1.0

223–621*

7.0 oz

208–085*

1.5 oz

208–082*

7.5 oz

223–622*

7.0 oz

TWIST LOCK

223–628*

1.3 oz

223–623*

7.3 oz

02286

Models

CIRCULAT-

ADAPTERS

1/4 npsm inlet &

return ports

Models

* Stainless

223–624*

ING

214–019 223–626*

Steel Models

208–250

223–625*

210–097

19307–452

Page 20

The

WARRANTY

Graco

warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this warranty defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’ ten recommendations.

, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment proven

Graco Warranty and Disclaimers

s writ-

This warranty does not cover misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, instal lation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claim. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor and transportation.

DISCLAIMERS AND LIMITATIONS

The terms of this warranty constitute purchaser’s sole and exclusive remedy and are in lieu of any other warranties (express or implied), liabilities, including product liabilities, based on negligence or strict liability tial damages or loss is expressly excluded and denied. In no case shall Graco’ price. Any action for breach of warranty must be brought within two (2) years of the date of sale.

EQUIPMENT NOT COVERED BY GRACO WARRANTY

Graco makes no warranty respect to accessories, equipment, materials, or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motor Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

including warranty of merchantability or warranty of fitness for a particular purpose

, and Graco shall not be liable for

, and disclaims all implied

warranties of merchantability and fitness for a particular purpose

, switches, hose, etc.) are subject to the warranty

, any malfunction, damage or wear caused by faulty installation,

, and of any non–contractual

. Every form of liability for direct, special or consequen

s liability exceed the amount of the purchase

, with

, if any

, of their manufacturer

Graco

PLACE AN ORDER

, or call this number to identify the distributor

utor closest to you:

20 307–452

1–800–367–4023 T

Foreign Offices:

, contact your Graco distrib

oll Free

Sales

Belgium; Canada; England; Korea; Switzerland; France; Germany; Hong Kong; Japan

Offices:

GRACO INC. P.O. BOX 1441

PRINTED

IN U.S.A.

Phone Numbers

Atlanta, Chicago, Detroit, Los Angeles,

307–452 November 1980, Revised April 1995

FOR TECHNICAL ASSIST

information or assistance regarding the application of Graco equipment:

MINNEAPOLIS, MN

1–800–543–0339 T

55440–1441

ANCE,

service repair

oll Free