Page 1
2 3 4
© 2000 Graco 303-2-00 303199
Other things to avoid
Dont lift or carry your baby in the activity center.
Dont adjust the activity center with your baby in it.
Dont use the activity center for commercial use.
Dont use the activity center if it is broken or damaged.
When NOT to use your Tot Wheels Entertainer
Do not use until your child can sit up alone.
When your child can walk unaided.
When your child reaches 30 lbs. in weight.
When your child has grown over 32 inches in height.
If your activity center has become broken or damaged.
If you havent prepared a safe play space for your baby.
When to use your Tot Wheels Entertainer
Your baby should be able to sit unaided and be able to
support most of his/her body weight with his/her legs
(about 6 months old).
Both feet should be able to touch the floor.
Congratulations on your purchase
of a Graco
®
Tot Wheels Entertainer
®
activity center!
Graco is the recognized leader in the
design and manufacture of quality baby
products. We believe your new Graco
®
Tot Wheels Entertainer®activity center is a
wise choice, promising many hours of
enjoyment for your baby.
Before using your activity center, please
take a few minutes to read this Owners
Manual. The short time you spend reading
these instructions will help you use your
activity center properly.
Customer Satisfaction
Our goal is to make every product the best it
can be! We are also committed to supporting our
products after purchase. If you would like to speak
with us about your product, please contact our
Customer Service Department at 1-800-345-4109
or visit our Internet website, www.gracobaby.com.
Our knowledgeable staff will be ready to answer
any questions you may have concerning parts, use
or maintenance. When you call, please have the
model and serial numbers ready so your call
may be processed quickly and efficiently.
Lets play safe.
Graco®activity centers have been designed with your childs enjoyment in mind. It is your responsibility to ensure your babys safety
by following these guidelines and using simple common sense. Lets work together to keep your baby safe and happy.
Graco is concerned about the safety of every child who uses one of our products. We know that parents and other caregivers
are equally concerned about the safety of their children. There are certain safety precautions which you must always take to
help minimize the risk that a baby using one of our mobile activity centers will be harmed. Specifically, the parent or caregiver in
charge of the baby should always follow these rules.
1. Never leave your baby unattended.
Most accidents happen to children while they are unsupervised. At a minimum, the caregiver should be in the same room with
the baby at all times keeping the baby under a watchful eye. Because a baby can propel a mobile activity center at surprising
speed and is eager to explore all sorts of potential hazards, direct and diligent supervision by the caregiver is required at all
times. If you believe proper supervision of your baby cannot be guaranteed, or that your home presents particular dangers from
which the baby cannot be adequately protected while using our mobile activity center, we suggest that you not use this product
and that you consider instead an activity center without wheels, swing, playard, or other fine Graco
2. Properly prepare your babys play space neutralize potential hazards.
Potential hazards in the room must be removed or guarded against before placing a baby in a mobile activity center. Keep in
mind that the mobile activity center gives the baby the ability to move around the play area much more quickly than would
otherwise be possible. That means its important to prepare play space by installing and using gates, removing objects from
reach, and closing doors to keep the baby away from potential hazards, such as:
Stairs
Steps
Raised thresholds
Driveways and sidewalks
Ramps or inclines
Decks
Ranges, heaters, fireplaces, hot
liquids and other heat sources
Blind or drape cords
Objects on tables
Dangling electrical cords or small appliances
Pots and pans on stoves
Books on shelves
Bathtubs or open toilets
Swimming pools or other containers filled with liquid
Any other dangers unique to your environment
Only your commitment to safety can give your child the safe, happy playtime you desire.
OWNERS MANUAL
Model No. ______________
Serial No. ______________
Dear Customer,
Please fill in the model
and serial numbers
above from the label
on the underside of
the tray.
Models 4430 and 4440 Series
Tot Wheels Entertainer
Activity Center
®
Page 2
®
activity center
®
activity center
®
product for your baby.
When you are able to watch your baby at all times while
playing in the activity center.
When you have prepared your babys play space
according to these guidelines.
If the tray of your activity center is lower than your babys waist
level when your child stands in the activity center.
If you havent blocked access to stairs and steps.
If you havent assembled the activity center according
to these instructions.
Dont use the activity center with your child in it on a
table or countertop.
Keep dangling electrical cords out of babys reach, such as
an iron on an ironing board, lamp cords, etc.
STAIR HAZARD:
Avoid serious injury or death.
Block stairs/steps securely before
using walker.
Avoid falls and other hazards. Never allow
walker to be pushed while child is in it.
Never leave child unattended. Always keep
child in view while in walker.
Use only on flat surfaces free of objects that
could cause the walker to tip over.
To avoid burns, keep your child away from
hot liquids, ranges, radiators, space heaters,
fireplaces, etc.
To reduce the chance of your child slipping out
of the seat, check that both of your childs feet
touch the floor.
Never carry the product with the child in it.
Discontinue using walker should it become
damaged or broken.
Read all instructions before assembly and use
of this product.
Keep instructions for future use.
PARTS LIST
CHECK that you have all the parts listed below
BEFORE assembling your activity center.
If any parts are missing, call
Customer Service at 1-800-345-4109 or visit our
Internet website, www.gracobaby.com.
THIS PRODUCT REQUIRES ADULT ASSEMBLY.
Tools required: Wrench or pliers, screwdriver
Nut
Screw (4)
Seat rod with threads
Tray
Pin (2)
Base
Seat
Spoiler
(on certain models)
Page 3
6 7 85
303-2-00 303199
To Attach Seat
Step 1.
On playtray models,
remove playtray from
activity center tray by
unsnapping both side
tabs from under tray.
Step 2.
Insert the pegs on the seat
back into the four holes
located at the rear of the tray.
Underneath the tray,
insert the four screws
into the centers of the
pegs. Press down on
the seat back to help the
screws connect with
pegs. Tighten the
screws securely,
but do not
overtighten.
Bottom of
seat back
Plastic pegs
To Attach Base
Step 1.
Place base on floor with wheels
down.
Step 2.
Open tubes of tray assembly
as shown until they latch.
Step 3.
Front tube has plastic T ends.
Tilt tray assembly as shown.
Insert one plastic T into slot
on the inside front of the base.
Repeat on opposite side, flexing
tube inward if needed to
engage the slot.
Step 4.
Lower rear tube so holes
in ends of tube line up with
two holes in back of activity
center base.
Be sure that plastic T pieces
remain in their slots.
Step 5.
Insert pin into hole
as shown, through
tray tube, and out
through base hole
on the other side.
Press firmly until tab
snaps over head of pin.
Repeat on other side.
Be sure all parts of tray
and base are securely
fastened, with T pieces
in their slots and tabs
holding pins firmly.
Push
Left
bracket
Right
bracket
Bent end seated
in channel
Nut
Step 3.
With the tray assembly upside down and its front
facing you, pull up on one of the tube ends until the
tubes snap into the first height position.
Insert seat rod through hole in left bracket, then through
the tunnel of the seat.
Step 4.
Now push the threaded end of the seat rod through the
right bracket hole. Turn the bent end of the rod so it fits
securely into the left bracket channel. Push it into place.
Place nut on seat rod threads and tighten securely with
wrench or pliers.
Seat rod
inside seat
tunnel
Head
of pin
Tab holds
pin
Page 4
Avoid
serious injury or death.
DO NOT use product
without the five friction
strips under the base.
!!
Make sure strips are
!
kept clean.
!!
Clean strips with
!
WATER ONLY.
Step 1.
To raise your activity center,
hold the base with one hand
while lifting the tray with the
other hand.
Adjust the tray so that it is no
lower than waist level when
your child is standing in the
activity center.
Step 2.
To lower (or fold) your activity
center, reach underneath the
tray and squeeze the finger
latches, holding them in
while you lower the tray.
Tray should lower easily.
DO NOT force tray down or
unit could be damaged.
To Use Parking Stands
(on certain models)
To Adjust the Activity Center
Remove your child from the activity
center before making any adjustments.
To install parking stands (two in
the front and one in the back), lift
base slightly, depress button on
front of stands and push stands
up until they snap into place.
To use parking stands, lift base
slightly and push stands down
until they snap into place.
To release parking stands, lift
base slightly and depress button
on front of stands. Push stands
upward into storage position.
Caring for the Activity Center
Make sure five friction strips under base are kept
clean. Clean with water only.
For cleaning vinyl seat, metal and plastic parts
other than friction strips, use only household soap
or detergent and warm water. NO BLEACH.
Excessive exposure to sun or heat could cause
fading or warping of parts.
!!
When parking stands are in use, it is still possible
!!
for your child to move the activity center.
!!
Be sure to engage both parking stands.
!!
Never place the activity center on a table or
!!
countertop.
Friction strips under base
Friction Strip Feature
To Attach Decals
Place decals on front of the
tray and base as shown.
Rub over decals with hand
or clean cloth to assure
adhesion.
Page 5
10 11 129
303-2-00 303199
To Assemble the Playtray
(on certain models)
Step 2.
Line up front of
playtray with
front edge of
activity center
tray as shown.
Step 3.
Push playtray down so both
side tabs snap under the
activity center tray.
Bar, two beads,
one ring
Teether and
stalk (style
may vary)
Phone
and cord
Steering wheel
and cap
Do not install the playtray while
your baby is in the activity center.
CHECK that you have all the parts
listed at right before assembling your
playtray.
Push and twist the ring and
two beads onto the toy bar.
Snap the toy bar into the holes
in the playtray; slight curve in
toy bar must curve away from
steering wheel. Be sure both
ends of the toy bar are firmly
snapped into the playtray.
Once the toy bar is inserted into
the playtray, you will not be able
to remove it.
Push end of phone cord
through small hole in tray,
then tie a knot under the tray.
Pull on phone cord to make
sure cord is secure.
Push wheel cap
onto steering wheel,
then push assembly
into large hole in
tray. Check that all
four tabs go into
hole in tray.
Insert teether stalk into
the small square hole in
the tray.
Step 1.
Assemble the toys on the tray as shown.
Step 4.
CHECK that playtray is secure
on activity center by pulling up
on playtray.
Do not lift this
product by the playtray.
To Remove the Playtray
To remove tray, pull the two
side tabs outward, and lift up
playtray.
Snap music keys in
place over the printed
circuit board.
Stickers
Place three stickers on front of
tray as shown. Rub over
stickers with hand or clean
cloth to assure adhesion.
Music key (3)
Page 6
Shorter teeth
on bottom
Step 1.
To mount beads on bar: flatten
ring at one end of bar as
shown and push through
hole in center of each bead.
Step 2.
Place ring on top of
a mounting post.
Shorter teeth must
be on the bottom, as
shown. Top of mounting
post will be even with top
of ring. Snap cap into place
inside mounting post and turn
it up to one half turn until it
locks in place. Repeat with
the other ring, post and cap.
Step 3.
Mount posts onto front
corners of activity center
tray as shown until they snap
securely into place. Center of
bar should curve away from
the seat, not toward it.
Step 4.
Insert the two prongs on a toy
base into a cap at the notches.
Step 5.
Turn toy base one quarter turn
until you feel the toy snap into
place. Check that toy is firmly
inserted by pulling on the toy.
Toy is removable (turn it the
other way with a little pressure)
so that you can replace it with
other toys when desired (sold
separatelysee the enclosed
leaflet).
Bar and beads
Mounting
post
and cap
(2 each)
Mix N Move
®
toys
(styles may vary)
To Assemble the Mix N Move
®
Toy Gym (on certain models)
Before assembling, check that you have all the parts
listed below:
Line up the pegs on the
bottom of the spoiler with
the two holes at the back of
the activity center and push
the spoiler in until it snaps
in place. It will not be
removable.
Do not allow spoiler to
block seat by inserting it
backwards.
To Attach the Spoiler
(on certain models)
Avoid falls and other hazards. Never
allow unit to be pushed while child is in product.
Page 7
13
303-2-00 303199
Replacement Parts
Instructions for ordering activity center parts:
Complete form below. Your activity center model
number MUST be included on the form to ensure proper
replacement parts. Your model number can be found
on a sticker on the underside of the tray. Payment
must accompany your order.
Model Number
(Must be filled in)
SHIP TO:
Name
Address
City, State, Zip
( )
Telephone
Account #:
Expiration date:
Signature:
Tray
Seat
Rear wheel
Seat rod/nut
Caster
Hardware
Pin
Parking stand
Toy gym
Star
Spinning rings
Playtray with toys
Spoiler
Check enclosed
(payable to Graco Childrens
Products Inc.)
Charge to credit card:
Visa
MasterCard
Discover
Parts List:
Tray .........................................
Seat .........................................
Rear wheel ..............................
Seat rod/nut .............................
Caster ......................................
Hardware .................................
Pin ...........................................
Parking stand* .........................
Mix N Move toy gym* .............
Mix N Move star*.......................
Mix N Move spinning rings*.......
Playtray with all toys* ...............
Spoiler*......................................
* Certain models only
Price:**
$ 15.00
$ 13.00
$ 8.00 (each)
$ 7.00
$ 5.00 (each)
$ 5.00
no charge
$ 5.00 (each)
$ 18.00
$ 8.00
$ 8.00
$ 20.00
$ 7.00
** Prices subject to change without notice.
Return the form below with payment to:
GRACO CHILDRENS PRODUCTS INC.
CUSTOMER SERVICE DEPARTMENT
P.O. BOX 100, MAIN STREET
ELVERSON, PA 19520
IF YOU NEED HELP
If you have any questions or if you need any part not
listed, please call toll-free:
1-800-345-4109
or visit our Internet website, www.gracobaby.com.
Total:
Shipping
& handling*: $5.00
6% sales tax
(PA only):
Total amount
due:
*Outside the continental U.S., please
call for shipping cost.
Loading...