Graco 4118 User Manual

234

© 1997 Graco 291-12-97

Congratulations on your purchase of a
Graco

®

Entertainer™activity center!

Graco is the recognized leader in the
design and manufacture of quality baby
products. We believe your new Graco

®

Entertainer™activity center is a wise
choice, promising many hours of
enjoyment for your baby.

Before using your activity center, please
take a few minutes to read this Owner’s
Manual. The short time you spend reading
these instructions will help you to use your
activity center properly.

Customer Satisfaction

Our goal is to make every product the best it
can be! We are also committed to supporting our
products after purchase. If you would like to speak
with Graco about your product, please contact our

Customer Service Department at 1-800-345-4109.

Our knowledgeable staff will be ready to answer
any questions you may have concerning parts, use
or maintenance. When you call, please have the
model and serial numbers ready so your call
may be processed quickly and efficiently.

Model No. __________
Serial No. __________

Dear Customer,
Please fill in the

model and serial
numbers above
from the label
under the tray
of your new
Entertainer™
activity center.

OWNER’S MANUAL

Model 4118

Failure to follow these warnings and the assembly

instructions could result in serious injury or death.

THIS PRODUCT REQUIRES ADULT ASSEMBLY.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF THIS PRODUCT.

If you experience any difficulties, please contact the Customer Service Department.

KEEP INSTRUCTIONS FOR FUTURE USE.
THIS PRODUCT IS FOR USE ONLY by a child who is able to sit upright unassisted,

unable to walk, weighs less than 30 pounds, and is less than 32 inches tall.

EXCESSIVE EXPOSURE TO SUN OR HEAT could cause fading or warping of parts.
DO NOT USE THIS PRODUCT if it is damaged or broken.

THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE.

Strings can cause strangulation! DO
NOT place items with a string around
your child’s neck, such as hood
strings or pacifier cords. DO NOT
suspend strings over the activity
center or attach strings to toys.

Never leave child unattended. Always
keep child in view while in this product.

Never lift or carry this product with
child in it.

Product may gradually move across
the floor as child plays in it. Watch for
movement of product and be sure
child stays away from hazards in the
area such as stairs, cords, hot liquids,
pools, sources of heat and anything
else that may injure your child.

The Entertainer

Activity Center

™

CARE AND MAINTENANCE

FROM TIME TO TIME CHECK YOUR ACTIVITY
CENTER for loose screws, worn parts, torn material

or stitching. Replace or repair the parts as needed.
Use only Graco

®

replacement parts.

REMOVABLE CLOTH SEAT may be machine
washed in lukewarm water on delicate cycle and
drip-dried. DO NOT MACHINE DRY. NO BLEACH.

TO CLEAN FRAME, use only household soap or
detergent and warm water. NO BLEACH. Use only
a damp cloth to clean the musical star.

PARTS LIST

CHECK that you have all the parts listed

below BEFORE assembling your

Entertainer™ activity center. If any parts

are missing, call Customer Service at

1-800-345-4109.

Tool required: Screwdriver

Teether

toy

Loop and rings

Seat

Clicker and

screw

Tray and seat ring

Base

Seat lock

and screw

Tumbler and

two screws

Do not use product with a child who
can tip over or climb out of product.

To avoid tipovers, place product on
flat, level floor/ground. Adjust legs to
same height so that the tray is level
before placing child in product.

Leg (3)

Duck pond and ring

5

291-12-97

6 87

Snaps visible

RIGHT

WRONG

Buttons

Line

To Assemble Your
Entertainer™ Activity Center

Step 1.

Turn the tray over and
locate the hole that the
seat lock screws into. Place
the seat lock on the tray as
shown and screw it to the
tray. DO NOT overtighten
screw—seat lock must be
free to slide.

Step 2.

Four tabs are located
behind the indentations
inside the seat ring.
Remove the seat ring by
pulling the four tabs out
from under the tray, one
at a time, while lifting the
seat ring.

Step 3.

Put the seat ring upside
down inside the cloth seat.
The high side of the seat
ring goes to the back of the
seat, where the warning
label is located.

Attach the seat to the seat
ring by tucking the seat
edge into the channel and
snapping the grommets on
the pegs.

Step 4.

Turn the seat over and
push the seat down into the
seat ring.

Step 5.

Snap the seat ring back
onto the tray. Make sure all
four tabs are snapped onto
the inside lip.

Pattern side UP

Solid color inside

Grommet

Pattern side

Step 6.

Turn tray over. Push one leg into socket in tray exactly as
shown until it snaps into place. Repeat for other two legs.

Step 7.

On top of tray, CHECK that
snaps are visible through
slots. Pull on leg to be sure it
is securely attached.

Step 8.

Slide the leg tubes on the tray onto the leg tubes on the
base as shown.

HINT: If a tray leg tube will not slide onto the base leg tube,
twist the base tube slightly to line up the parts.

Push in the buttons on each of the upper leg tubes and
adjust the activity center to the desired height.
The bottom edge of the upper tubes must be even with one
of the three lines on the lower leg tube.

CHECK that all three leg tubes are set to the same
height.

Button

faces seat

Step 9.

Assemble the toys on the tray as shown. The mirror,
squeaker, and music button are already assembled.

Tighten screw until
clicker does not
move freely—DO
NOT overtighten—
then loosen screw
slightly.

Set duck pond in round
space provided. Then place
retainer ring over it, pushing
all four tabs into slots in tray.

Insert teether
stalk into the tray.

Squeaker

Mirror and music button—
DO NOT allow liquids
around music button.

Mount ring toys onto loop,
then insert ends of loop into
holes on tray. Short end of
loop goes directly over leg.
The loop and ring toys will
not be removable.

Place tumbler
into oval space
as shown, then
use two screws
provided to
attach it from
underneath tray.
DO NOT over­tighten screw.

NOTE: Most toys may
be removed from tray
for cleaning or storage.

To Use the Seat Lock

Push gently on latch and
turn the seat until latch
engages in one of the four
stop positions.

To allow seat to swivel
again, pull lock out.

To Adjust the Seat Height

Do not adjust height while child is in

activity center.

Step 1.

Press in the buttons on
each leg to adjust seat
to desired height. The
bottom edge of the upper
tubes must be even with
one of the three lines on
the lower leg tube.

For your child’s safety, all three legs

must be set to the same height. Tray must be level.

(Note:
Squeaker
will not work
in storage
position.)

9

291-12-97

10

Tray at proper height

Step 2.

After adjusting height of the seat, CHECK that your
child’s feet can rest completely on the floor of your
activity center

. Tray should not be too high or too low.

Remove child and readjust height if necessary.

Replacement Parts

Instructions for ordering activity center parts:

Complete form below. Your model number MUST be
included on the form to ensure proper replacement parts.
Your model number can be found on a sticker on the bottom
of the tray. Payment must accompany your order.

Return the form below with payment to:

GRACO CHILDREN’S PRODUCTS INC.

CUSTOMER SERVICE DEPARTMENT

P.O. BOX 100, MAIN STREET

ELVERSON, PA 19520

IF YOU NEED HELP

If you have any questions, please call toll-free:

1-800-345-4109

Model Number

(Must be filled in)

SHIP TO:

Name

Address

City, State, Zip
( )

Telephone

Total:
6% sales tax

(PA only):
Total amount

due:

Check enclosed
(payable to Graco Children’s
Products Inc.)

Charge to credit card:

Visa
MasterCard
Discover

Account #:

Expiration date:
Signature:

Mirror
Musical star
Teether toy
Squeaker and button
Loop and rings
Tumbler and screws
Clicker and screw
Duck pond and ring
Cloth seat
Seat ring and bearings

Seat lock and screw
Complete tray unit
Height buttons and

springs
Retainer rings
Spring covers with

retainer rings
Complete base unit

Parts List:

Mirror .............................................................

Musical star ....................................................

Teether toy ....................................................

Squeaker and button ....................................

Loop and rings ..............................................

Tumbler and screws ......................................

Clicker and screw ..........................................

Duck pond and ring .......................................

Cloth seat ......................................................

Seat ring and bearings ..................................

Seat lock and screw ......................................

Complete tray unit (with legs, height .............

springs and height buttons)

Height buttons and height springs only ........

Retainer rings ................................................

Spring covers with retainer rings ..................

Complete base unit (with legs, retainer ........

straps, spring covers, and retainer rings)

Price:*

$ 5.00
$ 5.00
$ 5.00
$ 5.00
$ 5.00
$ 5.00
$ 5.00
$ 5.00
$ 14.50
$ 7.00
$ 5.00
$ 25.00

$ 5.00
$ 5.00
$ 5.00
$ 20.00

* Prices subject to change

without notice.

TRAY TOO HIGH TRAY TOO LOW