Graco 3A1907C Instructions - Parts Manual

Instructions-Parts

Remote Displa

For changing system settings on a Graco Control Architecture™ controlled Reactor® .

Important Safety Instructions
Read all warnings and instructions in this manual and the Reactor
manual. Save these instructions.

24K338

y Module Kit

3A1907C

EN

PROVEN QUALITY. LEADING TECHNOLOGY.

ti18310a

Contents

Component Ide

Remote Display Module Screens......................... 4

Installation.......................................................... 6

Maintenance ...................................................... 6

ntification..................................... 3

Upgrade Softw
Replace Tear O

Parts.................................................................. 7

Graco Standard Warranty.................................... 8

are........................................ 6

ff Sheet................................ 6

2

3A1907C

Component Identification

Component Ident

ification

To prevent da
press button
plastic card

User Interface
Figure 1

NOTICE

mage to the softkey buttons, do not

s with sharp objects such as pens,

s, or fingernails.

Button Function

Activate remo
When activate
the current o
system in sta

Not used.

Not used.

Usetomove
screen.

Press to change a setpoint.

Press to acknowledge an error.

Press to
shown on
above ea

te display module.

d, press to stop

peration and put the

ndby.

from screen to

select specific operation

the display directly

ch key.

3A1907C 3

Remote Display M

odule Screens

Remote Display Module Screens

ADM Not Found

This screen i
disconnecte
secure.

s displayed when the ADM is

d. Ensure all cable connections are

ADM Disabled

This screen is displayed when the system is first

turned on. Press

to activate the system.

The screen below shows A and B heat zones
enabled, actual temperatures, spray pressure, and
mode. The actual pressure is also shown. The A and
B drum icons show an estimated amount of material
inside each drum.

Icon Mode

Spray

Jog

Park

Home Screen

This screen displays the actual temperature for the
A material, B material, and heated hose at the gun.
This screen also indicates which heat zones are on
and what mode the pump is in.

Error Display

Thisisthehomescreenwithanactiveerror. Press

to acknowledge the error.

Icon

See operation manual for more information about
error codes.

Mode

Alarm — High Priority Error

Deviation — Medium Priority
Error

Advisory — Low Priority Error

4

3A1907C

Remote Display M

odule Screens

Temperature S

Use this screen to view the actual and target
temperatures for A material, B material, heated hose
at the gun, and estimated drum level.

At this scree
minor adjust
as the ambien
and other en
course of th

Turn on a heat zone: Press one of the softkey
buttons to turn on or off the corresponding heat zone.

Adjust temperature setpoint: Press
left and right arrow keys to select which temperature
setpoint you want to modify. Press the up and down
arrows to change the temperature.

n you can turn on heat zones and make

ments to the temperature and pressure

t temperature, drum temperature,

vironmental variables change over the

e spray day.

creen

and use the

Pressure Scre

Use this screen to view actual pressures for A and B
components at the fluid manifold, A and B pressure
setpoint, number of cycles, number of flow units
pumped, estimated drum level, and park the pumps.

Adjust pressure setpoint: Press
and down arrows to change the pressure.

Icon Function

en

.Presstheup

Press to
setpoin

Press to park the system
pumps.

edit the pressure

t.

Icon Function

Press t

ints.

setpo

Press to enable or disable the
A component heat zone.

to enable or disable the

Press

ponent heat zone.

Bcom

Press to enable or disable the
heated hose heat zone.

cates that the heat zone

Indi

n. A blank box indicates

is o

t the heat zone is off.

tha

o edit the temperature

Press t

Presstostopproportioner.

Press

o start proportioner.

to clear cycle counter

3A1907C 5

Installation

Installation

Reference parts illustration on next page.

1. Shutdown syst
shutdown inst

2. Remove CAN 2 k
enclosure an

3. Disconnect C
existing bul
(CAN-1 MCM)

4. Attach spli
Connect CAN
cable (5) to

5. Attach CAN

6. Route CAN c
Connect ca
assembly

Note

Order CAN cables if the heated hose
assembly does not have a CAN cable.

em. See operation manual for

ructions.

nockout from electrical

d install bulkhead fitting (7).

AN cable (CAN-1 TCM-H) from

khead fitting (F). Leave CAN cable

connected to fitting.

tter (2) on new bulk head fitting (7).

cable (CAN-1 TCM-H) and CAN

splitter.

cable (5) to bulk head fitting (F).

able (8) under fluid manifold.

ble (8) to CAN cable in heated hose

.

Maintenance

Upgrade Software

Order 16M459
Control Arch
3A1244 for in

Replace Tear Off Sheet

1. Peel away t

2. Install a n

for an upgrade token. See Graco

itecture Module Programming manual

structions.

he dirty protective sheet.

ew protective sheet (6) on the display.

• 24N449 —

• 121006 —

7. Connect
at the j
port on
remote

8. Instal

l the protective cap (4) on the unused CAN

port.

50 ft (15.2 m)

150ft(45.7m)

CAN cable (3) to heated hose assembly

oint before the whip hose and either CAN

the remote display module (1). Keep the
display module near spray area.

6 3A1907C

Parts

Parts

24K338 Remote

Ref.

1 24L952

2 124654

3 124003

4 121262

5

615M483

7

8 123652

9 16M459

Part Description

MODULE, display

CONNECTOR, splitter; (2) M12 (m) x M12 (f)

CABLE, can, male/female; 16.4 ft (5 m)

CAP, vinyl

121000

CABLE, CAN, female/female; 1.6 ft (0.5 m)

SHIELD, membrane; (10 pack)

121612

CONNECTOR, bulkhead, male/female

CABLE, can, male/female; 11.5 ft (3.5 m)

TOKEN, Reactor, E30i and EXP2i

Display Module Kit

HPTCM
255774

Qty.

1

1

1

2

1

1

1

2

1

6

1

9

5

CAN-1

CAN-2

F

7

CAN-1MCM

HEATED HOSE

8

3

ti18311b

3

3A1907C

7

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its
name to be free from defects in material and workmanship on the date of sale to the original purchaser for use.
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of
twelve mont
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance
with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction,
damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper
maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco
be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures,
accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation,

ation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

oper

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized
Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace
free of charge any defective parts. The equipment will be returned to the original purchaser transportation
prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be
made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The
buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost
profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available.
Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT,
MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not
manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of
their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of
these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco
supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold
hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices
and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be
drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en
Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou
en rapport, directement ou indirectement, avec les procédures concernées.

hs from the date of sale, repair or replace any part of the equipment determined by Graco to be

Graco Information

For the latest information about Graco products, visit www.graco.com.

To place an order, contact your Graco Distributor or call to identify the nearest distributor.

Phone: [phone] or Toll Free: 1-800-328-0211 Fax: [phone]

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

For patent information, see www.graco.com/patents.

Original Instructions. This manual contains English. MM 3A1907

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2012, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

Revised August 2012