Mobile Lubrication Library
Telehandler Loadall
Suggested automated lubrication system layout for Telehandler Loadall
333504B
Kit No.: 24R378, G3, USP, 21PT
Maximum System Working Pressure: 3000 psi (206 bar, 20.7 MPa)
Important Safety Information
Read all warnings and instructions in all
related manuals. Save all instructions.
Related Manuals
Manual No. Manual Title
3A0414 G3 Pump
3A0525 Pressure Relief Valve
3A0528 Remote Manual Run
3A0860 USP Valves
The information contained in this document is only a recommendation for an automatic lubrication system and is not intended to
replace the installation and maintenance instructions provided by the original equipment manufacturer.
Fluid leaks from incorrectly installed or ruptured components, and/or failure to verify the components are properly installed and tested, can result in serious injury such
as fluid spraying in the eyes or on skin and fluid injection,
or equipment damage.
To prevent injury or equipment damage, installation must
be done by a professional and tested prior to use. Consult Parker literature for specific hose assembly instructions. These instructions are available from your Parker
representative or at www.Parker.com/pdf.
Mobile Lubrication Library
Suggested Lube Points
USP Valves
LUBE POINT INFORMATION
Lube Point USP Outlet Bearing Description USP Block
1 5 King pin upper right SB#2 Single
2 6 King pin lower right SB#2 Single
3 1 King pin upper left SB#2 Single
4 2 King pin lower left SB#2 Single
5 3 Steering arm left SB#2 Single
6 4 Steering arm right SB#2 Single
7 5 Boom pivot left SB#3 Single
8 6 Telescope ram rear SB#3 Single
9 7 Upper compensating ram SB#3 Single
10 8 Main lift boom cylinder upper SB#3 Single
11 1 Boom pivot right SB#3 Single
12 2 Main lift boom cylinder lower SB#3 Single
13 3 and 4 Lower compressing ram SB#3 Double
14 5 King pin upper right SB#4 Single
15 6 King pin lower right SB#4 Single
16 7 Steering arm right SB#4 Single
17 8 Trunion right SB#4 Single
18 1 King pin upper left SB#4 Single
19 2 King pin lower left SB#4 Single
20 3 Steering arm left SB#4 Single
21 4 Trunion left SB#4 Single
Mobile Lubrication Library
USP Volume
Dispense
Mobile Lubrication Library
Part
Number
96G099 PUMP, G3-G-12MX-4L0L00-UDMVA1R2 (see manual 3A0414)
571036 KIT, accessory, cover
571028 KIT, accessory, pressure relief (see manual 3A0525)
24E406 KIT, valve, USP, 6 outlet (see manual 3A0860)
24E407 KIT, valve, USP, 8 outlet (see manual 3A0860)
571032 KIT, remote manual run, 12V, w/ cable (see manual 3A0528)
24N007 KIT, accessory, mounting, USP, 6-8
16U586 KIT, accessory, hose, 100 ft
556773 HOSE, end female swivel SAE 4 JIC
556763 FITTING, 4 JIC 1/8 pm
555749 CONNECTOR, 4 JIC 1/8 pm
557393 COUPLING, 1/8 fp x 1/8 mp x 1-1/4 HEX
556402 FITTING, 1/4 x 1/8 nptf hex
557349 PLUG, dryseal 1/8 nptf
16U587 KIT, accessory, guard, scuff, 75 ft
15K783 FITTING, elbow, street, 1/8
127009 TIE, cable, 14.75’ x .31” black
16U982 KIT, accessory, hose, 200 ft
16U933 KIT, accessory, guard, scuff, 160 ft
24F467 PLUG, USP, doubling plug
557944 CLAMP, 7/16, tube 4TS6-14002
127012 CLAMP, hose, .375 OD hose
563178 COUPLING, extension 1/8 female to 1/8 male
127013 FITTING, swivel, JIC 37D size #4
24R378: Recommended Kit Parts List
Description
Qty
1
1
1
2
2
1
4
1
8
25
30
21
1
4
1
5
4
1
1
4
20
20
4
42
USP VALVES* AND ACCESSORIES
Part Number Description
24E408 KIT, valve, USP, 10 outlet
24E409 KIT, valve, USP, 12 outlet
24E410 KIT, valve, USP, 14 outlet
24E411 KIT, valve, USP, 16 outlet
24N008 KIT, mounting bracket, 10-12 outlets
24N009 KIT, mounting bracket, 14-16 outlets
*see manual 3A0860
Typical Pump Installation
Pressure Relief
To Lube Points
USP
Valve
G3
Pump
To Fuse/Power
Manual Run
Button
Mobile Lubrication Library
Mobile Lubrication Library
Graco Information
For the latest information about Graco products, visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590
All written and visual data contained in this document reflects the latest product information available at the time of publication.
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2013, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original information. This manual contains English. MM 333504
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
www.graco.com
August 2013, revised January 2014
Loading...