Instructions–Parts List
STAINLESS STEEL, WATERBASE COMPATIBLE
310537C
Back Pressure Valve
Used with abrasive fluids in circulating systems to provide regulated
back pressure to the spray gun(s) and to maintain proper circulating
pressure throughout the system. For professional use only.
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
EN
300 psi (2.1 MPa, 21 bar) Maximum Inlet Pressure
200 psi (1.4 MPa, 14 bar) Maximum Regulated Pressure
Model 916154
Stainless Steel Back Pressure Valve,
with carbide wear parts, for use with abrasive fluids
Table of Contents
Warnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data 7. . . . . . . . . . . . . . . . . . . . . . . . . .
Graco Standard Warranty 8. . . . . . . . . . . . . . . .
8717A
Graco Information 8. . . . . . . . . . . . . . . . . . . . . . .
INSTRUCTIONS
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result
in serious injury.
D This equipment is for professional use only.
D Read all instruction manuals, warnings, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.
D Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
D Check the equipment daily. Repair or replace worn or damaged parts immediately.
D Do not exceed the maximum working pressure of the lowest rated system component. The maxi-
mum inlet pressure of this equipment is 300 psi (2.1 MPa, 21 bar). See the Technical Data on
page 7.
D Follow the Pressure Relief Procedure on page 4 if the spray tip clogs and before cleaning,
checking or servicing the equipment.
D Route hoses aaway from traffic areas, sharp edges, moving parts, and hot surfaces.
D Do not expose Graco standard hoses to temperatures above 180_F (82_C) or below –40_F
(–40_C).
D Do not use the hoses to pull the equipment.
D Use only fluids and solvents that are compatible with the equipment wetted parts. See the Techni-
cal Data sections of all the equipment manuals. Read the fluid manufacturer’s warnings.
D Always wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid and
solvent manufacturers.
D Wear hearing protection when operating this equipment.
D Comply with all applicable local, state and national fire, electrical, and other safety regulations.
2 310537
KEY
A Fluid Supply Line
B Air Spray Gun
C Fluid Pressure Regulator
D Air Supply Line
A
Installation
E Adjusting Screw
F Back Pressure Valve
G Fluid Return Line
B
Fig. 1
C
CAUTION
Handle the back pressure valve with care to avoid
damaging the diaphragm.
D
G
Connect the line to the 1-1/4 in. npt(f) inlet and outlet.
Make sure the flow direction agrees with the IN and
OUT markings on the valve body.
The back pressure valve is adjustable to control the
fluid pressures in a circulating system from 5 to 200 psi
(0.3 to 14 bar, 0.03 to 1.4 MPa).
E
F
8719A
Installing the Back Pressure Valve
Install the back pressure valve in the spray gun return
line. See Fig. 1.
Operation
NOTE: The back pressure valve controls pressure
ahead of its intake.
Turn the adjusting screw clockwise to increase pres-
sure and counterclockwise to decrease pressure.
Adjust the pump pressure and back pressure valve for
the best spraying combination and for proper circulation of fluid.
If more than one spray station is used, install the back
pressure valve in the fluid supply line after the last
station. This will help maintain proper circulating
pressures in the system.
Flush the back pressure valve with a compatible
solvent whenever the rest of the system or unit is
being flushed. Open the back pressure valve before
flushing by turning the screw counterclockwise.
310537 3
Service
Pressure Relief Procedure
WARNING
PRESSURIZED EQUIPMENT HAZARD
The system pressure must be manually relieved to
prevent the system from starting or spraying accidentally. To reduce the risk of an injury from accidental spray from the gun, splashing fluid, or
moving parts, follow the Pressure Relief Proce-
dure whenever you:
D are instructed to relieve the pressure,
D stop spraying,
D check or service any of the system equipment,
D or install or clean the spray nozzle.
1. Shut off the pump.
2. Open the dispensing valve, if used.
3. Open the fluid drain valve to relieve all fluid pressure, having a container ready to catch the drainage.
Service Procedure
NOTE: Regular cleaning and inspection of the valve,
based upon the degree and kind of service, is
essential.
1. Shut off the pump and open the back pressure
valve by turning the adjusting screw (13) counter-
clockwise until no spring pressure is felt. Relieve
all air and fluid pressures in the system.
2. Remove the back pressure valve from the fluid
line.
3. Disassemble the valve and clean it with a suitable
solvent. See the parts drawing, page 5.
5. Check for chips or dirt that could puncture the
membrane or diaphragm before assembling the
valve.
6. Check if the gasket (17) needs to be replaced.
7. Lubricate the threads of the diaphragm retainer
(11).
8. Install the diaphragm parts onto the valve
housing (15). Torque the retaining nut (20) to 10 to
12 ft-lb (13.5 to 16 N-m).
9. Carefully inspect the seat (10) for damage, wear,
or dirt. These things could cause the regulated
pressure to creep. Replace the seat if necessary.
10. Replace the seat gasket (14) when replacing the
seat (10). Torque the seat to 15 to 20 ft-lb (21 to
27 N-m).
11. To remove or install the gauge (8), use the wrench
on the square portion of the gauge stud only.
CAUTION
Use thread sealer sparely on the gauge’s male
threads when installing it to avoid plugging the
gauge.
12. Lubricate both sides of the spring plate (7) and
spring (5) with lithium-base grease.
13. Lubricate the adjusting screw threads.
14. Assemble the remaining parts.
15. Tighten the regulator cap screws (1) finger-tight,
then torque them to 120 to 130 in-lb (13.6 to 14.7
N-m) in a criss-cross pattern. See the TOP VIEW
in the parts drawing.
4. Carefully inspect the diaphragm (12) for cracks or
other damage. Replace if necessary.
4 310537
16. Install the back pressure valve back in the fluid
line.
Parts
13
7
19
1
1
1
See TOP VIEW
Torque to 10–12 ft-lb
2
(13.5–16 N-m)
3
PTFE side down
Torque to 15–20 ft-lb
4
(21–27 N-m)
Apply anaerobic pipe
5
sealant to threads
Apply lithium-base grease
6
7
Lubricate threads
TOP VIEW
5
3
6
7
5
6
Torque screws (1) to 120–130 in-lb
(13.6–14.7 N-m) in order shown
2
20
1
6
2
4
Model 916154
16
22
12
3
Stainless Steel Back Pressure Valve
Includes items 1 to 22
Ref.
No. Part No. Description Qty.
1 101682 SCREW, soc hd cap;
1/4–20 x 5/8 6
18
3 111697 PLUG, sq hd pipe; 1/4 npt 1
5 104144 SPRING, compression 1
7 160033 PLATE, spring 1
17
8n 187873 GAUGE, 0 to 200 psi
(0 to 1.4 MPa, 0 to 14 bar) 1
7
11
21
10
4
8
5
14
10n 616439 SEAT, stainless steel & tungsten
carbide 1
11 616440 RETAINER, diaphragm, stainless
steel & tungsten carbide 1
12n 172193 DIAPHRAGM 1
13 186872 SCREW, adjusting 1
14n 171117 GASKET, acetal copolymer 1
15 187878 HOUSING 1
16 164864 PLATE, diaphragm 1
17n 171912 GASKET, cellulose fibre 1
5
3
15
18n 171913 GASKET, cellulose fibre 1
19 209027 CAP 1
20 160741 NUT, retaining 1
21 160742 PELLET, nylon 1
22 157277 O-RING, Thiokolr 1
8718A
* These parts are included in Repair Kit 916139,
which may be purchased separately.
n Keep these spare parts on hand to reduce down
time.
310537 5
7.25 in.
(184 mm)
Dimensions
4 in. (102 mm)
diameter
1-1/4 npt(f)
inlet and
outlet
8717A
6 310537
Technical Data
Maximum inlet pressure 300 psi (21 bar, 2.1 MPa). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regulated pressure range 5 to 200 psi (0.3 to 14 bar, 0.03 to 1.4 MPa). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inlet and outlet size 1-1/4 npt(f). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gauge port size 1/4 npt(f). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wetted parts 304 & 316 stainless steel, tungsten carbide, celcon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diaphragm: nylon fabric base, with impregnated buna-N, and material side is PTFE coated
Weight 8.5 lb (3.9 kg). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thiokol
r is a registered trademark of the Thiokol Chemical Corporation.
310537 7
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited
warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment
determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
For the latest information about Graco products, visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you:
Phone: 612–623–6921 or Toll Free: 1–800–328–0211 Fax: 612–378–3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 310537
8 310537
International Offices: Belgium, China, Japan, Korea
Graco Headquarters: Minneapolis
GRACO INC. AND SUBSIDIARIES S P.O. BOX 1441 S MINNEAPOLIS, MN 55440–1441 S USA
Copyright 1996, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revised May 2012
Loading...