1-1/4”
7-1/16”
A
B
1/8” npt
dispense
outlet
13/32”
mounting
holes
3/8” npt
(2) supply
inlet/outlet
Model 114903 Shown
Instructions-Parts List
®
GL-1
For Single–Line Parallel Automatic Lubrication Systems.
Important Safety Instructions
Read all warnings and instructions in this manual and manual 309015.
See manual 309015 for Automatic Lubrication System installation,
operation, and troubleshooting. Save all instructions.
SKIN INJECTION HAZARD
Fluid from the injector, leaks, or ruptured components
can inject fluid into your body and cause extremely serious injury, including the need for amputation. Fluid
injected into the skin might look like just a cut, but it is a
serious injury. Get immediate surgical treatment.
Fluid splashed in the eyes or on the skin can also
cause serious injury. The equipment may be pressurized already, or it could become pressurized by an
automatic lube cycle initiated by Lubrication Controller
(timer). Disconnect power to the timer, and disconnect
the air supply to the pump module to ensure that the
system is depressurized. See the pressure relief pro-
cedure in Pump Module manual 308955.
Injectors
308953M
EN
Part No. Description Dimension A Dimension B Bare Manifold Part No.
114901
114902
114903
114904
114905
114909
Injector, GL–1, one point
Injector, GL–1, two point
Injector, GL–1, three point 1.25 in. (31.7 mm) 4.23 in. (107.5 mm) 114913
Injector, GL–1, four point 2.50 in. (63.4 mm) 5.47 in. (139.0 mm) 114914
Injector, GL–1, five point 3.75 in. (95.1 mm) 6.71 in. (170.5 mm) 114915
Injector, GL–1, replacement
GL-1 Injector Models
2.48 in. (63.0 mm) 114911
3.00 in. (76.0 mm) 114912
Injector Service Parts
2
4 torque to
35-40 ft-lbs
(47-54 N.m)
9
18
11
1
13
16
19
15
6
Manifold
(not included)
9
7
Torque to 50-54 ft-lbs (68-74 N.m)
17
5
12
3
8
Injector Service Parts
Item Description Qty Part No.
1
Injector body
2
Adjusting screw
3
Lock nut
4
Packing housing
5
Zerk fitting and cap assembly
6
Copper gasket
Adapter bolt
7
(used on all manifold models)
8
Indicator pin
9
Steel gasket
Fluoroelastomer o–ring (PN
11
114997)
12
Displacement piston
13
Compression spring
15
Plunger
16
Fluoroelastomer packing
17
Fluoroelastomer packing
18
Fluoroelastomer packing
19
Inlet valve
11 114906
1 114907
1 114908
1 114916
1 114918
1-
12
1
1
1
1
1
1
1
1
Included in Injector Repair Kit 241234 only
Available Kits
Use Only Genuine Graco Repair Parts
Graco Part No. 115119 . . . . . Plastisol Injector Cover
(see page 3 for installation instructions)
Graco Part No. 115120 . . . . . . . . . . . . . Crossover Kit
(for connecting the outlets of injectors
for increased output)
Graco Part No. 241234 . . . . . . . . . Injector Repair Kit
(See Kit 241234 parts in Injector Service Parts list.)
2 308953M
Injector Cover Kit 115119
groove
21
22
Plastisol cap for Graco GL-1 Injectors
Item Description Qty
21 Plastisol cap 1
22 O-ring 1
Installation Instructions
1. Apply a light coating of transparent lubricant to the
inside of cap (21).
2. Slide cap (21) over the indicator stem of the injector
far enough to cover the groove in the piston plug.
3. Slide the o-ring (22) down over the cap to the
groove in the piston plug, forcing the cover into the
groove to form a seal.
Injector Cover Kit 115119
Technical Data
Maximum operating pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 3500 psi (24 MPa, 241 bar)
Suggested operating pressure . . . . . . . . . . . . . . . . . . . . . . . . . 2500 psi (17 MPa, 172 bar)
Reset pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600 psi (4.1 MPa, 41 bar)
Output volume per cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . carbon steel, stainless steel, copper, fluoroelastomer
Recommended fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N.L.G.I. #2 grease down to 32° F (0° C)
*Maximum adjustment setting is when adjusting screw (2) is just making contact with the indicator pin (8) with no inlet
pressure. Turn adjusting screw clockwise (in), to reduce output. To adjust, loosen lock nut (3) and turn adjusting
screw (2) the number of turns indicated on the GL-1 Volume Adjustment Table to obtain the desired volume. Tighten
lock nut (3) when desired volume setting is reached
GL-1 Volume Adjustment Table
Description
Maximum Adjustment* 0 0.080 1.31
360° Clockwise Turn 1 0.071 1.16
360° Clockwise Turn 2 0.062 1.02
360° Clockwise Turn 3 0.053 0.87
360° Clockwise Turn 4 0.044 0.72
360° Clockwise Turn 5 0.035 0.57
360° Clockwise Turn 6 0.026 0.43
360° Clockwise Turn 7 0.017 0.28
Minimum Adjustment 8 0.008 0.13
.
adjustable*: 0.008 to 0.08 in.
in.
Volume
3
Number of
Turns
3
cc
308953M 3
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
For the latest information about Graco products, visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590
All written and visual data contained in this document reflects the latest product information available at the time of publication.
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 1999, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original instructions. This manual contains English. MM 308953
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
www.graco.com
Revised September 2014
Loading...