INSTRUCTIONS-PARTS
LIST
307–283
This
manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
INSTRUCTIONS
Low Pressure, High Volume
“Red
Alert” Filters
300 psi (2.1 MPa, 21 bar) Maximum Working Pressure
20
gpm (76 liter/min) Flow Capacity
225 in.2 (1450 cm2) Filtering Area
Model 213–062
With
30 mesh (590 micron) element
Model 213–063
With
60 mesh (250 micron) element
Model 213–064
With
100 mesh (149 micron) element
First
choice when
quality counts.
Rev. D
Supersedes Rev. C
Model 213–065
With
150 mesh (95 micron) element
Model 213–066
With
200 mesh (74 micron) element
Model 214–002
Less
element – See
numbers.
Parts
03708
on page 6 for element
GRACO INC. P.O. BOX 1441
COPYRIGHT
Graco
Inc. is registered to I.S. EN ISO 9001
MINNEAPOLIS, MN
1977, GRACO INC.
55440–1441
Table
of Contents
Symbols
Warnings 2.
Installation 4
Service 5
Parts 6
Technical
Graco Warranty 8.
Graco
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Phone Number8. . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNING
EQUIPMENT MISUSE HAZARD
Equipment
D
This equipment is for professional use only
misuse can cause the equipment to rupture or malfunction and result in serious injury
Warning Symbol
WARNING
This
symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
Caution Symbol
CAUTION
This
symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
corresponding instructions.
.
.
D
Read all instruction manuals, tags, and labels before operating the equipment.
D
Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.
D
Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
D
Check the equipment daily
D
Do not exceed the maximum working pressure of the lowest rated system component. This equip
ment has a
D
Route the hoses away from the traffic areas, sharp edges, moving parts, and hot surfaces. Do not
expose Graco hoses to temperatures above 180
D
Use fluids or solvents that are compatible with the equipment wetted parts. See the
Data
section of all the equipment manuals. Read the fluid and solvent manufacturer’s warnings.
D
Comply with all applicable local, state and national fire, electrical and other safety regulations.
300 psi (2.1 MPa, 21 bar) maximum working pressure
. Repair or replace worn or damaged parts immediately
.
_F (82_
C) or below –40
_F (–40_C).
.
Technical
PRESSURIZED EQUIPMENT HAZARD
Spray
from the gun, hose leaks, or ruptured components can splash fluid in the eyes or on the skin
and cause serious injury
D
Relieve the pressure before removing, cleaning, or servicing the equipment.
D
Do not stop or deflect fluid leaks with your hand, body
.
, glove, or rag.
-
D T
D
307–283
ighten all the fluid connections before operating the equipment.
Check the hoses, tubes, and couplings daily
Permanently coupled hoses cannot be repaired; replace the entire hose.
. Replace worn, damaged, or loose parts immediately
.
Notes
3307–283
Installation
Notes:
o clean or service the filter without shutting down
T
the system, install a dual filter or a filter bypass as
explained below
The numbers and letters in parenthesis refer to the
Figures and the Parts Drawing.
Be sure to allow 4 in. (102 mm) minimum clearance
below the filter for easier removal of the bowl (9).
.
Dual Filter System
This
setup enables you to redirect the fluid to another
filter while one filter is cleaned or serviced.
Install two filters as shown in Fig. 1. Both filters must
have an adapter (A) and drain valve (B) in the filter
bowl (9) to relieve fluid pressure and drain the filter
before removing the bowl. Install four suitable shutof
valves (D), one at each filter inlet and outlet, to redirect
the fluid and isolate the filter when not in use.
f
Filter Bypass System
This
setup enables you to redirect fluid through pipes
which bypass the filter
filter.
Install the filter and bypass pipes as shown in Fig. 2.
An adapter (A) and drain valve (B) must be installed in
the filter bowl (9) to relieve fluid pressure and drain the
filter before removing the bowl. Install four suitable
shutof
f valves (D), one at the filter inlet; the filter outlet;
the bypass pipe inlet; and the bypass pipe outlet, to
redirect the fluid and isolate the filter while cleaning
and servicing.
, while cleaning or servicing the
WARNING
T
o reduce the risk of component rupture and
serious injury, do not exceed the 300 psi (2.1 MPa,
21 bar) maximum working pressure of this filter
the maximum working pressure of any other acces
sory or component in your system. Be sure that all
components and accessories are rated to with
stand the maximum working pressure of your
pump.
, or
-
-
D
Fig. 1
D
D
9
A
B
D
9
D
A
B
Fig. 2
9
A
B
4 307–283
Service
WARNING
PRESSURIZED EQUIPMENT HAZARD
Before removing, cleaning, or servicing the filter
close the inlet and outlet ball valves (D, Fig. 1) and
open the fluid drain valve (B) to relieve pressure.
CAUTION
,
Viton O-Ring
The
o-ring seals the bowl (9) to the housing (3). If
material leaks around the bowl, replace the o-ring (6).
Remove the bowl and o-ring. Clean the parts in a
compatible solvent. Be careful not to damage the
o-ring or sealing surfaces of the bowl and housing.
Before assembling, lubricate the parts with No. 2
grease.
If the filter will not be used for awhile, thoroughly
clean all the parts in solvent and blow them dry
before the paint dries and clogs the filter
prevent damaging the parts, do not clean them with
a wire brush or sharp object.
. T
o help
Indicator
The indicator provides gradual warning of a dirty
element. When the indicator shows 3/4 red, clean the
element. If not cleaned promptly
opens and fluid will not be filtered.
Replace the indicator assembly (1) if the indicator is
not working correctly (it is always red, or never red).
, the filter bypass valve
Bypass Valve
The
valve opens when a dirty element causes the
filter’
s outlet pressure to drop 15 psi (100 kPa, 1 bar).
below the inlet pressure. This keeps the system pres
sure steady and prevents the element from collapsing.
Replace the bypass valve (2) if it is damaged or worn.
Bowl, Element, and Spring
Graco
recommends keeping a spare bowl (9), element
(7), and spring (8) on hand. Before removing the bowl,
direct the fluid through the bypass valve (2) or shut
down the system. Relieve fluid pressure by opening
the drain valve (B).
Holding the bowl with a wrench to keep it from turning,
screw the drain plug (10) out. After the fluid has
drained out, remove the bowl, element, and spring.
Replace immediately with the spare bowl, element,
and spring to keep the paint from drying on the hous
ing (3) and other parts. Install the element with the
dome end up. Lubricate the threads of the bowl before
screwing it into the housing; tighten it securely
Clean the bowl, element, and spring you removed with
a compatible solvent before the paint dries. Do not use
a wire brush or sharp object to clean. Store until need
-
ed.
Note:
Clean the filter element (7) with a small paint
brush. Blow out lodged particles with air
for damage. Replace if ruptured.
, and inspect
-
.
-
5307–283
Model 213–062 to 213–066
Include Items 1–10
Model 214–002
Include Items 1–6, 8–10
1
Parts
Note:
but does not include a filter element as standard.
Select the desired filter element from those listed
under Ref. No. 7
Note:
do include a filter element as standard, as listed under
Ref. No. 7.
Ref.
No. Part No. Description Qty.
Model 214–002 includes items 1–6 and 8–10,
All other models are the same as 214–002, but
1 104–125 INDICAT
2
3
4
5
2 102–694 VALVE, bypass 1
3 172–741 HOUSING, filter 1
4 175–000 PLA
5 100–055 SCREW
no. 6 x 1/4
6* 104–712 O-RING; Viton
7* 108–111 ELEMENT
108–112 ELEMENT
108–113 ELEMENT
108–115 ELEMENT
108–114 ELEMENT
8* 102–691
9* 172–745
10 104–663
SPRING, element
BOWL, filter
PLUG, pipe; 3/4 npt(f)
OR, filter
TE, instruction
, drive; type “u”,
, filter (Model 213–062 only)
, filter (Model 213–063 only)
, filter (Model 213–064 only)
, filter (Model 213–065 only)
, filter (Model 213–066 only)
1
1
2
1
1
1
1
1
1
1
1
1
6
* Recommended “tool box” spare parts. Keep these parts on
hand to reduce down time.
Order parts by the name and the series letter of the assembly
for which your are ordering.
7
8
9
10
6 307–283
03707
Technical
Category Data
Dimensions 6.06”
5.5” (140 mm) Deep;
1
1” (280 mm) High
Weight
Maximum Working Pressure
Flow Capacity
Filter Area
W
etted Parts
Viton is a registered trademark of the Du Pont Corporation.
7 lb (3.2 kg)
300 psi (2.1 MPa, 21 bar)
20 gpm (76 liters/min)
225 in.2 (1450 mm2)
Anodized Aluminum, V
Steel,
Data
(154 mm) Wide;
PTFE, Plated Steel
iton; 300 Series Stainless
7307–283
The
Graco
warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in
material
any
replace
operated
This
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution
Graco
installation,
This
verification
equipment
in
transportation.
Graco’s
remedy (including, but not limited to, incidental or consequential damages for lost
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two
date
GRACO
A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT
NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, gas engines,
switches,
in
In
hereunder,
breach
and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception
special extended or limited warranty published by Graco, Graco will,
any part of the equipment determined by Graco to be defective. This warranty applies only when the
and maintained in accordance with Graco’
warranty does not cover
of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
equipment with structures, accessories, equipment or materials not supplied by Graco, or the
operation or maintenance or structures, accessories, equipment or materials not supplied by Graco.
warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
material or
of sale.
making any claim for breach of these warranties.
no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor
sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above.
MAKES NO W
hose, etc.), are subject to the warranty
or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
of warranty
Graco Warranty and Disclaimers
for a period of twelve months from the date of sale, repair or
equipment is installed,
s written recommendations.
, and Graco shall not be liable
ARRANTY
, the negligence of Graco, or otherwise.
, AND DISCLAIMS ALL
, if any
for general wear and tear
IMPLIED W
, of their manufacturer
ARRANTIES OF MERCHANT
, or any malfunction, damage or wear caused by
improper design, manufacture,
The buyer agrees that no other
profits,
lost sales, injury to person or property
ABILITY AND FITNESS FOR
, MA
TERIALS OR COMPONENTS SOLD BUT
. Graco will provide purchaser with reasonable assistance
(2)
years of the
of
, and
, or any
FOR
GRACO CANADA CUST
The
parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent
judiciaires
TO
PLACE AN ORDER
avoir convenu que la rédaction du présente document sera en Anglais,
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
OMERS
Graco
Phone Number
, contact your Graco distributor
1–800–367–4023 T
ainsi que tous documents, avis et procédures
, or call this number to identify the distributor closest to you:
oll Free.
All
written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Foreign Offices:
Sales Offices:
Belgium, Canada, England, Korea, France, Germany
GRACO INC. P.O. BOX 1441
PRINTED
IN U.S.A. 307–283 June 1977, Revised July 1997
Minneapolis, Detroit, Los Angeles
MINNEAPOLIS, MN
, Hong Kong, Japan
55440–1441
8 307–283
Loading...