Page 1
Instructions–Parts List
Quiet ViscountR II
Hydraulic Motor
Used as hydraulic drive for reciprocating pumps.
For professional use only.
Model 223646, Series B
1500 psi (10 MPa, 103 bar) Maximum Hydraulic Fluid Input Pressure
Patent No. 4,792,291
Foreign Patents Pending
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
308048K
ENG
Table of Contents
Warnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Hole Layout 14. . . . . . . . . . . . . . . . . . . .
Dimensions 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data 15. . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco Phone Number 16. . . . . . . . . . . . . . . . . . . .
04471
Page 2
Symbols
Warning Symbol
WARNING
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
INSTRUCTIONS
This equipment is for professional use only.
Read all instruction manuals, tags, and labels before operating the equipment.
Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.
Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
Check equipment daily. Repair or replace worn or damaged parts immediately.
Notice Symbol
NOTICE
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
corresponding instructions.
Do not exceed the maximum working pressure stated on the equipment or in the Technical Data
for your equipment. Do not exceed the maximum working pressure of the lowest rated component
in your system.
Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech-
nical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
Handle hoses carefully. Do not pull on hoses to move equipment.
Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82C (180F) or below –40C (–40F).
Do not move or lift pressurized equipment.
Wear hearing protection when operating this equipment.
Comply with all applicable local, state, and national fire, electrical, and safety regulations.
3080482
Page 3
WARNING
SKIN INJECTION HAZARD
Spray from the gun, hose leaks or ruptured components can inject fluid into your body and cause
extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin
can also cause serious injury.
Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate surgi-
cal treatment.
Do not point the gun at anyone or at any part of the body.
Do not put your hand or fingers over the spray tip.
Do not stop or deflect leaks with your hand, body, glove or rag.
Do not “blow back” fluid; this is not an air spray system.
Always have the tip guard and the trigger guard on the gun when spraying.
Check the gun diffuser operation weekly. Refer to the gun manual.
Be sure the gun trigger safety operates before spraying.
Lock the gun trigger safety when you stop spraying.
Follow the Pressure Relief Procedure on page 7 if the spray tip clogs and before cleaning,
checking or servicing the equipment.
Tighten all fluid connections before operating the equipment.
Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.
Permanently coupled hoses cannot be repaired; replace the entire hose.
Use only Graco approved hoses. Do not remove any spring guard that is used to help protect the
hose from rupture caused by kinks or bends near the couplings.
MOVING PARTS HAZARD
Moving parts can pinch or amputate your fingers.
Keep clear of all moving parts when starting or operating the pump.
Before servicing the equipment, follow the Pressure Relief Procedure on page 7 to prevent the
equipment from starting unexpectedly.
308048 3
Page 4
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
Ground the equipment and the object being sprayed. Refer to Grounding on page 6.
If there is any static sparking or you feel an electric shock while using this equipment, stop spray-
ing immediately. Do not use the equipment until you identify and correct the problem.
Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
Keep the spray area free of debris, including solvent, rags, and gasoline.
Before operating this equipment, electrically disconnect all equipment in the spray area.
Before operating this equipment, extinguish all open flames or pilot lights in the spray area.
Do not smoke in the spray area.
Do not turn on or off any light switch in the spray area while spraying or while there are any fumes
in the air.
Do not operate a gasoline engine in the spray area.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
Know the specific hazards of the fluid you are using.
Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
3080484
Page 5
Installation
WARNING
Maximum Hydraulic Input Pressure
The maximum safe hydraulic input pressure to this
motor depends on the pressure rating of the displacement pump to which it is connected.
Refer to the lower manual and the pump manual
for the maximum fluid working pressure and the
ratio. Never exceed the maximum fluid working
pressure of the pump. Serious injury or damage to
the equipment may result.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 7.
Be sure you always shut off the supply line shutoff
valve (E) first, and then the return line shutoff
valve. This is to prevent overpressurizing the motor
or its seals. When starting up the hydraulic system,
open the return line shutoff valve first.
NOTICE
Keep the hydraulic system clean
To reduce the risk of damaging the hydraulic power
supply, blow out all hydraulic lines with air, flush
thoroughly with solvent, and then blow out with air
again before connecting the lines to the motor.
NOTICE
Recommended Hydraulic Oil
Use Graco-approved Hydraulic Oil, Part No. 169236
(5 gal) or 207428 (1 gal)) or a premium, ISO grade
46 petroleum-based hydraulic oil containing rust and
oxidation inhibitors and anti-wear agents.
Before using any other type of oil in this motor,
contact your Graco distributor. Unauthorized use of
lesser grade oil or substitutes may void the warranty.
Hydraulic Oil Working Temperature
The recommended hydraulic oil operating temperature is 80–115F (27–45C). The motor seals will
wear faster and leakage may occur if the pump is
operated at higher oil temperatures.
If the hydraulic oil temperature approaches 130F
(54C), check the hydraulic fluid supply cooling
system, filters, etc. and clean or repair as needed.
Refer to the complete pump manual for detailed installation information or contact your Graco distributor.
NOTE: A 1 in. npt seal (7) is supplied in a plastic bag
with the motor. Thread the seal onto the threads of
your hydraulic return line fitting (A). Thread the fitting
into the upper housing (53) and torque as needed.
Then tighten the seal (7) against the motor to provide a
secure seal. See Fig. 1.
53
A
Always plug the hydraulic inlets, outlets and lines
when disconnecting them to avoid introducing dirt
and other contaminants into the system.
Carefully follow the manufacturer’s recommendations
on reservoir and filter cleaning, and periodic changes
of hydraulic fluid.
Fig. 1
7
308048 5
04467
Page 6
Installation
Grounding
WARNING
For your safety, read the FIRE AND EXPLOSION
HAZARD WARNINGS on page 4, and ground
your entire system as instructed below. This section also includes details on how to connect the
grounding wire and clamp to the various hydraulic
motors.
Proper grounding is an essential part of maintaining a
safe system.
To reduce the risk of static sparking, ground the pump.
Check your local electrical code for detailed grounding
instructions for your area and type of equipment. Be
sure to ground all of this equipment:
1. Pump: use a ground wire and clamp as shown to
the right. Loosen the locknut (A) of the grounding
lug and washer. Insert one end of the wire (B) in
the grounding lug (14) and tighten the locknut
securely. See Fig. 2. Connect the other end of the
wire to a true earth ground, as recommended by
your local code. Order Part No. 237569, Ground
Wire and Clamp.
4. Spray gun: obtain grounding through connection to
a properly grounded fluid hose and pump.
5. Fluid supply container: according to local code.
6. Object being sprayed: according to local code.
7. Any pails used when flushing: Use only metal,
grounded pails when flushing. Make firm metal-tometal contact between the metal part of the spray
gun and the pail. Use the lowest possible pressure.
8. To maintain grounding continuity when flushing or
relieving pressure, always hold a metal part of the
gun firmly to the side of a grounded metal pail, and
then trigger the spray gun.
B
2. Hydraulic hoses and fluid outlet hoses: use only
electrically conductive hoses.
3. Hydraulic power supply and air compressor:
follow manufacturer’s recommendations.
Fig. 2
A
14
04468
3080486
Page 7
Service
Pressure Relief Procedure
WARNING
SKIN INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally. Fluid
under high pressure can be injected through the
skin and cause serious injury. To reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
are instructed to relieve the pressure,
stop spraying,
check or service any of the system equipment,
or install or clean the spray tip.
1. Lock the gun trigger safety.
2. Shut off the hydraulic power supply.
3. Close the supply line shutoff valve, and then the
return line shutoff valve.
Before you start:
Be sure you have all necessary parts on hand.
1. Repair Kit 223654 is available. The kit must be
purchased separately. An asterisk behind a reference number in the parts list, for example (21*),
indicates that the part is included in the repair kit.
2. Clean all parts as you disassemble them and
inspect them for wear or damage. Replace parts
as necessary. Use Loctite TL–242 thread
sealant, or the equivalent, when thread sealant is
specified.
Disassembly (Refer to Fig. 3)
NOTE: Use all the replacement parts that are in the
repair kit.
1. Flush the displacement pump if possible.
WARNING
4. Unlock the gun trigger safety.
5. Hold a metal part of the gun firmly to the side of a
grounded metal pail, and trigger the gun to relieve
pressure.
6. Lock the gun trigger safety.
7. Open the drain valve (required in your system),
having a container ready to catch the drainage.
8. Leave the drain valve open until you are ready to
spray again.
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, very slowly loosen the
tip guard retaining nut or hose end coupling and relieve
pressure gradually, then loosen completely. Now clear
the obstruction.
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 7.
2. Relieve the pressure.
3. Stop the pump at the bottom of its stroke.
NOTICE
Avoid getting dust or dirt in the motor during service.
Cleanliness is essential when repairing an hydraulic
motor.
4. Disconnect the displacement pump hoses. Disconnect the hydraulic hoses and plug all hydraulic
connections and lines to prevent contamination.
308048 7
Page 8
Service
Disassembly (continued – refer to Fig. 3)
NOTICE
When removing the displacement pump, hold it
securely. The pump is heavy and could fall off the
motor.
5. Disconnect the displacement pump from the
motor, as explained in your separate pump manual.
6. Place the hydraulic motor in a bench vise.
7. Push or lightly tap the piston (30) up as far as
possible.
NOTE: The tie rod nuts (19), socket screws (51), cap
screws (36), and retainer (34) are fastened with Loctite TL–242. Heat may be used sparingly to soften
adhesive sealant during disassembly.
8. Remove the cap screws (12), the drip pan (16),
the drip cover (18), and machine screw (20) before
loosening the tie rod nuts. Then remove the four
tie rod nuts (19). Loosen the nuts (B) on the hydraulic tube (4) and loosen the tie rods (57).
9. Remove the motor from the vise and lay it in a
pan.
13. Unscrew the top and bottom compression nuts (B)
on the hydraulic tube (4). Rotate the upper housing
(53) and remove the tube, being careful not to
damage the flare (A). Allow the oil to drain from
the motor into the pan.
NOTE: With the tie rods removed, the assembly may
separate at the joints between the cylinder (29) and
the upper and lower housings (53 and 25).
14. Rock the upper housing (53) to work it free and lift
it about 3 inches off the cylinder (29). The cylinder can stay in the lower housing (25).
15. Hold the trip rod (31) with an adjustable wrench on
the flats of the rod, and remove the top hex nut
(46) from the trip rod.
16. Remove the upper housing (53).
17. Remove the trip rod guides (37), compression
springs (45) and valve spool (38) from the upper
housing. Inspect the bearing inside of the guide
(35) in place. If bearing is damaged replace item
35.
NOTE: Inspect the trip rod (31) above the shoulder for
damage. There must be no reduction in diameter.
Replace if necessary.
10. Remove one detent assembly: retaining plug (39),
o-ring (41), spring (40), ball guide (42) and ball
(43). If the ball or other parts stick in the upper
housing (53), turn the motor over and tap lightly.
Do not allow the parts to fall into the motor. Repeat
the procedure for the other detent assembly.
11. Remove the tie rods (57), but do not remove the
crown nuts (44).
12. Remove the socket screws (51) and the end cap
(47). Pull the stop plug (48) from the upper housing (53).
18. Pull the trip rod and piston from the lower housing
(25) and cylinder (29). Place the piston flats (30) in
a vise; tighten the vise on the flats of the piston.
Use a face spanner to remove the retainer (34).
Remove the trip rod (31) from the piston (30).
19. Remove the trip rod locknut (27) and piston stop
(28). If the piston is replaced, remove the spring
(26) to use in the new piston.
20. Remove the bearing (23), packings (24), and
o-ring (21).
3080488
Page 9
Service
55
54
54a
7a
58
B
4
B
A
50
51
47
43
48
44
52
53
42
40*
41
39
31
34
28
27
56
54
54a
B
A
3
3a
*49
55a
B
7
5
6a
6
38
*45
37
46
37
45*
A
35
36
33*
57
29
33*
24*
25
23*
24*
21*
2
NOTE: Circled letters refer to connected points.
Fig. 3
*32
26
30
*17
20
16
14
15
19
18
13
12
04466
308048 9
Page 10
Service
Reassembly (Refer to Fig. 4)
1. Install the bearing (23*) in the lower housing (25).
Lubricate the seals (24*) with hydraulic oil. Install
them in the lower housing (25) with the lips facing
up toward the top of the motor.
2. Install the o-ring (21*) onto the lower housing (25).
3. Place the piston flats in a vise. Install the spring
(26) inside the piston (30). The compression rings
(32*) must be positioned with the joints about 180
opposed. Be sure the o-ring (17*) is in place.
4. Install the piston stop (28) and locknut (27) on the
trip rod. Torque the nut to 117–123 in-lb (13.2–13.9
N.m). Slide the trip rod (31) into the piston (30).
Apply thread sealant to the retainer (34) threads.
With the piston flats in a vise, tighten the retainer
until it is flush or below the piston surface. This is
important to prevent the retainer from backing out
during operation and damaging the motor.
NOTE: Set base (2) on workbench during reassembly.
5. Install the o-ring (33*) onto the cylinder (29). Install
the cylinder (29) into the lower housing (25).
6. Install the trip rod and piston into the cylinder (29)
and lower housing (25) so the piston is recessed at
least 1 inch (25 mm) from the top of the cylinder.
10. Remove the adjustable wrench. Seat the upper
housing (53) onto the cylinder (29), so the tube
fittings align with those on the lower housing (25).
Reinstall the hydraulic tube (4) and loosely tighten
the compression nuts.
11. Replace the o-ring (49*) on the stop plug (48).
Seat the plug into the upper housing (53).
12. Install the end cap (47), using thread sealant on
the socket screws (51).
13. Lubricate the threads of the tie rods (57) and install
them with lockwashers (52). If the crown nuts (44)
were removed, reinstall them and torque them
onto the rods to 70–80 ft-lb (95–108 N.m).
14. Torque tie rods into base, apply thread sealant to
tie rod threads, then torque the tie rod nuts (19) to
70–80 ft–lb (95–108 N.m).
15. With the motor on its side, install one detent
assembly: the ball (43), guide (42) with the con-
cave surface toward the ball, spring (40*), o-ring
(41) and retaining plug (39). Torque the plug to
145–160 in-lb (16–18 N.m). Repeat for the other
side of the motor.
7. If the bearing and guide (35) was removed, install
it on the upper housing (53) with the three screws
(36) (apply thread sealant).
8. Hold the flats of the trip rod with an adjustable
wrench and install the upper housing (53). The trip
rod will protrude from the top.
9. Slide the lower trip rod guide (37) and spring (45)
onto the trip rod. Install the spool (38) with the
detent at the top. Install the top spring (45) and
guide (37) on the trip rod. Install the top hex nut
(46). Torque the nut to 82–88 in-lb (9.3–9.9 N.m).
16. Slide the drip cover (18) onto the piston (30) up to
the o-ring (17). Install screw (20) into the piston.
Attach the drip pan (16) to the base using screws
(12).
17. Snugly tighten the compression nuts on the hydraulic tube (4) and torque to 60–80 ft-lb (81–108
N.m).
18. Install the motor on the displacement pump. Reconnect all fluid lines. Be sure the ground wire is
connected before operating the pump.
30804810
Page 11
Service
50
5
51
47
*49
55a
55
54
54a
7a
B
7
58
5
6a
B
6
6
46
37
45*
4
38
48
44
52
43
53
42
56
40*
B
41
9
39
54
54a
8
A
31
33*
57
29
33*
24*
25
23*
344
2
*45
B
6
37
A
A
1
Rings must be positioned with joints opposed
2
Lips must face up toward top of motor
Lubricate threads
3
4
Torque to 70–80 ft-lb (95–108 N.m)
5
Apply thread sealant
6
Torque to 60–80 ft-lb (81–108 N.m)
7
Torque to 117–123 in-lb (13.2–13.9 N.m)
8
Torque to 82–88 in-lb (9.3–9.9 N.m)
9
Torque to 145–160 in-lb (16–18 N.m)
35
36
5
34
5
3a
24*
2
3
28
27
7
21*
2
*32
1
26
14
15
5
4
19
30
20
18
13
16
*17
12
Fig. 4
04466
308048 11
Page 12
Model 223646, Series B
Parts
55
54
54a
7a
7
58
4
50
51
47
43
48
44
52
53
42
40*
41
39
31
34
28
27
56
54
54a
A
1
B
3
3a
*49
55a
B
5
6a
6
46
37
45*
38
*45
37
A
35
36
33*
57
29
33*
24*
25
23*
24*
21*
2
NOTE: See the service section for important
torque and lubrication information.
NOTE: Circled letters refer to connected points.
*32
26
30
*17
11
20
16
14
15
9
19
18
13
12
04466
30804812
Page 13
Model 223646, Series B
Parts
Ref.
No. Part No. Description Qty.
1 290331 LABEL, instruction, English 1
2 186221 BASE 1
3 110797 ELBOW, male, 3/4 npt
Includes item 3a 1
3a 110926 .O-RING, nitrile rubber 1
4 210108 TUBE 1
5 112574 ADAPTER, 3/4 npt (f) x
1–1/16–12 1
6 110791 TEE, 7/8–14 unf–2a x 1 1/16–
12un–2a, 37 flare for 3/4 in. dia.
tube, Includes item 6a 1
6a 110926 .O-RING, nitrile rubber 1
7 110876 ADAPTER, 1 –11-1/2 npt x
1 5/16–12un–2a, Includes item 7a 1
7a 110927 .O-RING, nitrile rubber 1
8 183695 LABEL, identification not shown 1
9 172975 LABEL, warning 1
10 100508 SCREW, type “u” drive,
No. 4 x 0.188 in. 4
11 172815 PLATE, warning 1
12 100333 SCREW, cap, hex hd;
1/4–20 x .0.5 in. 3
13 103875 ADAPTER, barbed hose, 1/8
npt x 0.25 in. (6.4 mm) ID hose 1
14 104029 GROUNDING LUG 1
15 104582 WASHER 1
16 210110 PAN, drip 1
17* 165295 O-RING, nitrile rubber 1
18 171397 COVER, drip 1
19 100155 NUT, hex jam, 5/8–18 4
20 101577 SCREW, machine, hex hd;
No. 10–20 x 0.375 in. 1
21* 110800 O-RING, buna–N 1
23* 186223 BEARING, piston,
bronze-filled PTFE 1
24* 110795 SEAL, u-cup, polyurethane 2
25 186218 HOUSING, lower 1
26 104664 SPRING, compression 1
27 103450 NUT, hex, self-locking, 5/16–18 1
28 181243 STOP, piston 1
29 186219 CYLINDER 1
30 188087 PISTON 1
31 171407 ROD, trip 1
32* 104103 RING, piston, compression 2
Ref.
No. Part No. Description Qty.
33* 166071 O-RING, nitrile rubber 2
34 171398 RETAINER 1
35 210292 BEARING and GUIDE 1
36 108538 SCREW, soc flat hd, self locking,
1/4–20 x 1/2 in. 3
37 183659 GUIDE, trip rod 2
38 183658 SPOOL, valve 1
39 186222 RETAINER, spring 2
40* 108522 SPRING, helical compression 2
41 110801 O-RING, nitrile rubber 2
42 167210 GUIDE, ball 2
43 101701 BALL, 1/4 in. dia. 2
44 104143 NUT, crown, 5/8–18 4
45* 171411 SPRING, compression 2
46 104105 NUT, hex lock, 1/4–20 1
47 180953 CAP, end 1
48 171416 PLUG, stop 1
49* 104093 O-RING, nitrile rubber 1
50 108132 RING, lift 1
51 101864 CAPSCREW, soc hd,
5/16–18 x 1 in. 3
52 100128 LOCKWASHER, spring, 5/8 in. 4
53 186217 HOUSING, upper 1
54 110792 ELBOW, 90, 7/16–20 unf–2a(m)
x 9/16–18 unf–2a(m), 37flare for
3/8 in. dia. tube, Includes item 54a 2
54a 110801 .O-RING, nitrile rubber 2
55 110799 PLUG, 9/16–18 unf–2b,
Includes item 55a 1
55a 110925 .O-RING, nitrile rubber 1
56 223608 TUBE, drain 1
57 171405 ROD, tie 4
58 105430 NUT, seal, 1 in. npt
supplied in a plastic bag 1
* These parts are also included in Repair Kit 223654,
which may be purchased separately.
Replacement Danger and Warning labels, tags and
cards are available at no cost. Label 290331 is also
available in the following languages:
German (Part No. 290396)
French (Part No. 290397)
Spanish (Part No. 290398).
308048 13
Page 14
Mounting Hole
Layout
4
3
2
2
Dimensions
1
5
6
2
4
1
02589
1
Four 0.437 in. (11.1 mm) dia. mounting holes
3.712 in. (9.45 cm)
2
3
3.464 in. (8.79 cm)
4.0 in. (9.84 cm)
4
5
2.0 in. (5.08 cm)
6
Three 5/8–11 UNC (2B) tapped holes
Gasket 161806 is not shown. Order Separately
7
3
1
1 in. npt Outlet
3/4 in. npt Inlet
2
11.25 in. dia. (285.8 mm)
3
24.94 in. (633.8 mm)
4
5
1.8 in. to top of 4.69 in. stroke
5
02631
30804814
Page 15
Technical Data
Category Data
Maximum hydraulic fluid input pressure 1500 psi (10 MPa, 103 bar). Also see the WARNING on
page 5.
Maximum hydraulic fluid flow 12 gpm (45.6 liter/min)
Hydraulic fluid consumption 1 gal. (3.8 liter) per 5 cycles
Effective piston area 4.9 sq. in. (31.6 cm2)
Piston rod diameter 2.5 in. (64 mm)
Stroke length 4.69 in. (119.1 mm)
Thrust at 1500 psi (10 MPa, 103 bar) 7300 psi (32 472 N)
Weight approx. 96 lb. (43.5 kg)
Loctite is a registered trademark of the Loctite Corp.
Sound Data
Hydraulic Pressure dB(A) at 20 cycles
per minute
1500 psi (10 MPa, 103 bar) 70 78 79
dB(A) at 30 cycles
per minute
dB(A) at 60 cycles
per minute
308048 15
Page 16
Graco Warranty and Limitation of Liability
Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of
any special extended or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or
replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed,
operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance or structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT
NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, gas engines,
switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance
in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
For the latest information about Graco products, visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you:
Phone: 612–623–6921 or Toll Free: 1–800–328–0211 Fax: 612–378–3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 308048
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
Graco Headquarters: Minneapolis
Copyright 1990, Graco Inc. is registered to ISO 9001
www.graco.com
Revised 08/2010
30804816
Loading...