Graco Inc 223392, 223390, 223391, 308011 User Manual
INSTRUCTIONS-PARTS
This
manual contains
INSTRUCTIONS and WARNINGS.
READ AND RETAIN FOR REFERENCE.
IMPORTANT
LIST
308–011
Rev A
SPRAY
4050
psi (280 bar) MAXIMUM WORKING PRESSURE
GUN EXTENSION
Model 223–390 12 in. (305 mm) long
Model 223–391 18 in. (457 mm) long
Model 223–392 24 in. (610 mm) long
Fits all Graco high pressure spray guns.
(Adapters available for other guns)
Includes DripLess
Order spray tip separately.
Tip Guard.
GUN NOT INCLUDED
WARNING
Pressure
T
o reduce the risk of serious bodily injury
fluid injection, splashing fluid or solvent in the eyes or
on the skin, or injury from moving parts or electric
shock, follow this procedure whenever you shut of
the sprayer
the spray system, when installing, cleaning or chang
ing spray tips, and whenever you stop spraying.
1.
Engage the gun safety latch.
2.
Shut of
spark plug).
Relief Procedure
, including
f
, when checking or servicing any part of
f the pump and unplug it (or disconnect the
3.
Disengage the gun safety latch. Hold metal spray
extension firmly to the side of a grounded metal
pail, and trigger the gun to relieve pressure.
4.
Engage the gun safety latch.
5.
Open the sprayer’s pressure drain valve, having a
-
container ready to catch the drainage. Leave the
valve open until you are ready to spray again.
If you suspect that the spray tip or hose is com
pletely clogged, or that pressure has not been fully
relieved after following the steps above,
SLOWL
pling to relieve pressure gradually
pletely
Y loosen the tip retainer nut or hose end cou
, then loosen com
. Now clear the tip or hose.
VER
-
Y
WARNING
Hazard of Using Fluids Containing Halogenated Hydrocarbons
Never use 1,1, 1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids con
taining such solvents in this equipment. Such use could result in a serious chemical reaction, with the possibil
ity of explosion, which could cause death, serious bodily injury and/or substantial property damage.
Consult your fluid suppliers to ensure that the fluids being used are compatible with aluminum and zinc parts.
GRACO INC. P.O. BOX 1441
COPYRIGHT
MINNEAPOLIS, MN
1990, GRACO INC.
55440–1441
-
-
-
-
INSTALLATION
Follow
the
Pressure Relief Procedure
page.
See the drawing below for assembling the extension.
Before installing the spray tip, start and prime the
sprayer.
Install the tip in the tip guard and be sure to install the
tip gasket. Screw the tip guard firmly onto the adapter
NOTE:
A Reverse-A-Clean IVt DripLess
Guard may be used in place of the one
supplied with the extension.
Flushing
Follow the flushing guidelines given in your seperate
pump instruction manual. Be sure to relieve fluid pres
sure, and then remove the spray tip before flushing.
This reduces the risk of static sparking and splashing
fluid in the eyes.
TIP NOT INCLUDED
4
on the first
t Tip
PARTS LIST
Model 223–390 12 in. (305 mm) long
Model 223–391 18 in. (457 mm) long
Model 223–392 24 in. (610 mm) long
REF
NO. PART
1
.
-
2
3
4
5
NO.
180–137 NUT
180–136
166–969 W
220–222
218–244
218–245
218–246
DESCRIPTION QTY
ADAPTER, tip
ASHER, tip
TIP GUARD
EXTENSION TUBE
12 in.
18 in.
24 in.
3
, gun
for Model 223–390
for Model 223–391
for Model 223–392
1
1
1
2
1
1
1
1
2
3
Must be purchased separately
SPRA
Y GUNS
Includes Reverse–A–Clean IV DripLess
T
ip Guard and a SwitchT
“SIL
VER” GUN
.
t
ipt
220–954
5000 psi (350 bar) Max. Working Pressure
SwitchTipt is
“CONTRACT
size 517.
OR” GUN
220–955
3600 psi (248 bar) Max. Working Pressure
SwitchTipt is
“BLACK MAX” GUN
size 517.
220–730
3600 psi (248 bar) Max. Working Pressure
SwitchTipt is
size 513.
5
ACCESSORIES
REVERSE-A-CLEANt
220–422
Uses fluid pressure to remove tip clogs. Purchase
SwitchTipt
ADAPTER GUN NUTS for other guns
Use in place of 180–137.
180–147
180–146
Maximum Working Pressure
Wetted
Weight
IV DripLess
separately
Fits Binks high pressure guns
Fits W
.
agner high pressure guns
TECHNICAL
Parts
.
. . . . . . . . . . . . . . . . . .
Stainless
223–390
223–391
223–392
GUN NOT INCLUDED
t T
ip Guard
DA
TA
.
. . . . .
.
. . . . . . . . .
.
. . . . . . . . .
.
. . . . . . . . . .
4050 psi (280 bar)
Aluminum, Plastic,
Steel, Plated Steel
6.9 oz (195 g)
8.4
oz (239 g)
10
oz (283 g)
Factory
Subsidiary and Affiliate Companies:
Branches:
GRACO INC.P.O. BOX 1441
Atlanta, Chicago, Dallas, Detroit, Los Angeles, W
est Caldwell (N.J.)
Canada; England; Switzerland; France; Germany; Hong Kong; Japan
PRINTED
MINNEAPOLIS, MN
IN U.S.A.
308–01
1 2–90
55440–1441
Loading...