Graci-lite Capper User Manual

Capper

User Manual

Please read user manual before operating

IV. Specifications:

●

DMX512 with 8 channels, Automatic operations, Sound
activated, and Master/slave

●

Super bright 3W LED Lamp

●

18pcs*12W Red, Green, Blue, and White 4 in 1

●

Color temperature less than 6000K

●

0 – 100% light dimmer

●

Multi-flash effect 1 – 10 time per sec open/close

●

Low power consumption. Est. 100,000 hours

●

Voltage: AC90V-240V/50 or 60Hz

●

Power: 170W

Note: There is a power linking socket on the

back that allows you to link another LED

fixture to this one. Since this fixture is 170W

it is advised that you do not connect more than

3 to one fixture for best performance.

Menu Panel

(located on back)

Channel Data Function

CH1 0 -10 None

CH4 – CH8 allowed

11 - 50 A1

51 - 100 A2

101 - 150 A3

151 - 200 A4

201 - 255 A5

CH2 0 - 39 Automatic Operation

40 – 49 Red

50 – 59 Green

60 - 69 Blue

70 - 79 Yellow

80 - 89 Cyan

90 - 99 Purple

100 - 109 White

110 - 119 Red + Green

120 - 129 Red + Blue

130 - 139 Red + White

140 - 149 Green + Blue

150 - 159 Green + White

160 - 169 Blue + White

170 - 179 Red + Green + White

180 - 189 Red + Blue + White

190 - 199 Green + Blue + White

200 - 209 Red + Green + Blue

210 - 255 Red + Green + Blue + White

CH4 Dim

CH5 Red

CH6 Green

CH7 Blue

CH8 White

III. DMX Channel List:

(For use with controller)

II.Menu:

When you press the “MENU” switch there are the following
options:

1. [D001]: This is the lights DMX address. You can press “UP” or “DOWN” to set it
from [D000] up to [D512] and press “ENTER” to confirm it. This function allows you
to put the light fixture in DMX mode so that you may use a controller if needed.

2. [IP01]: This is the lights IP address. You can press “UP” or “DOWN” to set it from
“IP01” up to “IP64” and press “ENTER” to confirm it.

3. [A1xx]: These are the static colors. You can press “UP” or “DOWN to set it from
[A1.01] up to [A1.19] and press “ENTER” to confirm it. These are preset colors.

4. [A2xx]: This is the color alternating effect. You can press “UP” or “DOWN to set the
speed from [A2.01] up to [A2.32] and press “ENTER” to confirm it. This mode
alternates between colors automatically.

5. [A3xx]: This is the color fade out and color fade in effect. You can press “UP” or
“DOWN to set the speed from [A3.01] up to [A3.19] and press “ENTER” to confirm it.

6. [A4xx]: This is the sound activated strobe effect. You can press “UP” or “DOWN” to
set it from [A4.01] up to [A4.19]. When the display is flickering, you can press “UP” or
“DOWN” to change the sensitivity of the sound activated effect from [01] to [04] and
press “ENTER” to confirm it.

7. [A5xx]: This is the automatic strobe effect. You can press “UP” or “DOWN” to set it
from [A5.01] up to [A5.19] and press “ENTER” to confirm it. When the display is
flickering, you can press “UP” or “DOWN” to change the speed of the strobe effect
from [01] to [32] and press “ENTER” to confirm it.

8. [A6xx]: This is all modes (except sound active mode). You can press “UP” or
“DOWN” to set it from [A6.01] to [A6.19] to change the speed, and press “ENTER” to
confirm it. This mode will alternate through all of the effects.

9. [A7xx]: This is the preset static color strobe effect. You can press “UP” or “DOWN”
to set it from [A7.01] to [A7.19] to change which preset static color strobe is working,
and press “ENTER” to confirm it.

10. [Rxxx] This is the red color dim. You can press “UP” or “DOWN” to set it from
[R000] to [R255] to dim the red color, and press “ENTER” to confirm it.

11. [Gxxx] This is the green color dim. You can press “UP” or “DOWN” to set it from
[G000] to [G255] to dim the green color, and press “ENTER” to confirm it.

12. [Bxxx] This is the blue color dim. You can press “UP” or “DOWN” to set it from
[B000] to [B255] to dim the blue color, and press “ENTER” to confirm it.

13. [uxxx]: This is the white color dim. You can press “UP” or “DOWN” to set it from
[u000] to [u255] to dim the white color, and press “ENTER” to confirm it.

(For use without controller)

I.Operation

This light has 4 functions:

1. DMX512 with 8 channels

2. Automatic operation

3. Sound Activated

4. Master/slave

Note: in order to use a DMX
controller you must make sure the
back panel is in DMX mode. To do
this press “MENU” until the LED
screen reads [D001], and the press
“ENTER” to confirm.