FCC and Industry Canada Identifi cations Numbers (and label locations)
FAMILY 1: FCC ID: J5XT3HEP
Industry Canada ID: 5916A-T3HEP
FCC ID: J5XT3HEP
IC: 5916A-T3HEP
Grace Industries, Inc. -- 2016-06
y
Safety Certifi cations
Intrinsically Safe, Sécurité Intrinséque
II 1 G Ex ia IIC T4 Ga
0891
TRAC11ATEX1129X
-40°C < T
< 40°C Um(max) 250VAC
A
IP67
FCC ID: J5XT3HEP -- Meets FCC Part 15
IC: 5916A-T3HEP -- Complies with Canadian ICES-003
WARNINGS!
WARNING! Changes or modifi cations not express-
ly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
WARNING! To prevent ignition of a hazardous atmosphere, battery must only be charged in an area known
to be nonhazardous.
WARNING! Substitution of components may impair intrinsic safety.
AVERTISSEMENT! Les changements ou modifi ca-
tions non expressément approuvés par la partie responsable de la conformité pourraient annuler l’autorité de l’utilisateur à utiliser cet équipement.
AVERTISSEMENT! Pour éviter l’infl ammation d’une
atmosphère dangereuse, les batterie doivent être
chargées seulement dans une zone connu comme
être non dangereuse.
AVERTISSEMENT! La substitution de composants
peut compromettre la sécurité intrinsèque.
FCC Statements
Changes or modifi cations not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to pro-vide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
Industry Canada Statements
This Class A digital apparatus complies with Canadian ICES-003.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.(select the class for your device)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur
de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Charger Adapter
Plugs Into Charging Key
Green
Charging Light
TPASS®3-R RECHARGEABLE
with Charging Key in Place
12 VDC Charging Adapter
Optional 120 VAC Charger
Adapter Available
Battery Charging LED Display
Charging: When the charging key is in place and
plugged into a power source, a steady Green LED will
glow below the left side button (left side when facing
the TPASS
Charging Complete: Unit is fully charged when the
steady green glow is replaced by a fl ashing Green dis-
play.
®
3-R unit).
The Low Battery Alarm will sound when the battery has
been exhausted to 20% of capacity (indicating approx.
1 hour operating time remains). Charging the battery is
necessary when low battery alarm sounds.
The low battery alarm is an easily recognized series of
two audio beep tones enunciated every fi ve seconds
when the TPASS
®
3-R is in the Sensing Mode.
Grace Industries, Inc. assumes no liability for mechanical, electrical, or other types of battery failure.
Pre-Alert and Alarm Time Periods
Alarm Time Pre-Alert Alarm
30 seconds Pre-Alert 18 to 23 seconds 30 to 35 seconds to Alarm
60 seconds Pre-Alert 48 to 53 seconds 60 to 65 seconds to Alarm
90 seconds Pre-Alert 78 to 83 seconds 90 to 35 seconds to Alarm
120 seconds Pre-Alert 108 to 113 seconds 120 to 125 seconds to Alarm
Warranty Information
Grace Industries, Inc. warrants TPASS®3-R to be free
from defects in workmanship and materials for a period
of one year from date of purchase. This warranty is
valid only when the returned TPASS
nied by a sales receipt or other proof of purchase that
states the date and location of purchase. Grace Industries, Inc. will not repair or replace any merchandise
under warranty which has been damaged because of
accident, misuse or abuse of the TPASS
possession or control of the consumer or outside of
Grace Industries Inc’s control. This warranty is void if
any attempt to repair or replace parts was made or attempted by other than qualifi ed Grace Industries, Inc.
personnel. This warranty is void if any of the sealed
compartments are opened or tampered with. Send all
returned merchandise, prepaid and accompanied by
proof of purchase to: Grace Industries, Inc., Repair Division, 305 Bend Hill Road, Fredonia, PA 16124. Customer is responsible for return shipping. Grace Industries, Inc. shall not be liable for any direct, incidental or
other consequential loss or damage arising out of the
failure of the device to operate.
The sole and exclusive remedy under all guarantees or
warranties, expressed or implied, is strictly limited to repair or replacement as herein provided. ALL IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO,
WARRANTIES OF FITNESS AND MERCHANTABILITY, ARE HEREBY LIMITED IN DURATION TO A PERIOD ENDING ONE (1) YEAR FROM THE DATE OF
PURCHASE. The warranty and liability set forth in the
prior paragraphs are in lieu of all other warranties, expressed or implied, in law or in fact, including implied
warranties of merchantability and fi tness for a partic-
ular purpose. Some states do not allow limitations on
how long an implied warranty lasts, so the above limitations may not apply to you.
This warranty gives you specifi c legal rights and you
may also have other rights which may vary from state
to state.
The information contained in this booklet is believed
to be accurate and reliable. Grace Industries, Inc. provides this information as a guide only.
®
TPASS
3-R technical assistance is available by contacting Grace Industries, Inc. at (724) 962-9231 or by email at
info@graceindustries.com.
For training purposes a copy of this information is
available by contacting Grace Industries, Inc.
www.graceindustries.com
© Grace Industries, Inc.
Printed in U.S.A.
®
3-R is accompa-
®
3-R while in
P/N: TP3-R ATEX 0616 UI
TPASS®3
RECHARGEABLE
USER’S INFORMATION
Only To Be R emoved By End User
ATEX CERTIFIED
TPASS®3
Rechargeable
Auto-ON Model
with Accountability
Key in Place
Grace Industries, Inc.
www.graceindustries.com
Ph. 724-962-9231 • Fax 724-962-3611
®
TPASS
Rechargeable
Manual ON/OFF Model
Solutions for Life Safet
3
TPASS®3 Intrinsically Safe Rechargeable
TPASS®3 may be utilized as part of an Automated Accountability System when used with other Grace monitoring equipment.
TPASS®3 Operating Instructions (120 seconds to Alarm used for example)
Always test the unit prior to each use
To Turn ON and OFF,
Manual
Activation
Emergency
Alarm
Button
Charging
Contacts
Manual Activation
®
3-R is in Sensing
®
3-R begins an audible
1) MOTION-ALARM: After 120 to 125 seconds of
no motion, TPASS
indicated by a rapid pulsing of two red LEDs while
sounding a rapidly modulated, loud audio alarm.
During Alarm, an emergency radio signal is transmitted to MX900, alerting personnel outside the immediate area that personnel may need assistance
2) PANIC ALARM: Panic Alarm can be activated
at any time (from Sensing Mode or Off Mode) by
pressing the Emergency Alarm Button.
®
3-R enters the Alarm Mode as
1. To Reset, press both side
buttons simultaneously when
accountability key is off unit.
2. To turn OFF, replace accountability
key and press both side buttons
simultaneously.
Emergency
Alarm
Button
Identifi cation
Window
Tether attached to
a fi xed position
Auto-ON Activation
ACTIVATING TPASS®3-R: When the TPASS®3-R is
removed from a storage position, the Accountability
Key automatically detaches, activating TPASS®3-R
into the motion Sensing Mode.
During activation, an operational signal of escalating
audio tones will be heard and an alternating display of
yellow LEDs indicates the TPASS
Mode. When TPASS
®
3-R is activated, its internal radio
transmits signals that are received by the MX900.
PRE-ALERT MODE: After approximately 108 to 113
seconds of no motion, TPASS
Pre-Alert sound and the alternating yellow LED display
is interrupted by the pulsing of two red LEDs. The PreAlert sound progressively becomes louder, indicating
TPASS®3-R is closer to going into Alarm.
ALARM MODE: There are two methods of activating
the Alarm Mode.
1) MOTION-ALARM: After 120 to 125 seconds of
no motion, TPASS
®
3-R enters the Alarm Mode as
indicated by a rapid pulsing of two red LEDs while
sounding a rapidly modulated, loud audio alarm.
During Alarm, an emergency radio signal is transmitted to MX900, alerting personnel outside the immediate area that personnel may need assistance
2) PANIC ALARM: Panic Alarm can be activated
at any time (from Sensing Mode or Off Mode) by
pressing the Emergency Alarm Button.
®
3-R is in Sensing
®
3-R begins an audible
D-Ring
Grip Clip
Auto-On
Accountability
Storage Key
Side View with
Accountability
Key in Place
Activation
Gasket Seal
Reset the Alarm Mode and return TPASS
Sensing Mode by simultaneously pressing both side
buttons.
TURN OFF: To turn TPASS
ability Key and press both side buttons simultaneously.
Sound
Port
Side View with
Accountability
Key OFF
Emergency
Alarm
Button
®
3-R OFF, replace Account-
®
3-R to
Mode Selection
AUTO-ON ACTIVATION
● Remove Accountability Key to automatically acti-
vate the unit into Sensing Mode.
ALARM
● Alarm Mode can be manually activated at any
time (from Sensing Mode or Off Mode) by
pressing the Emergency Alarm Button.
RESET
● When in Alarm, the TPASS
Sensing Mode by simultaneously pressing both
side buttons.
OFF
● Turn OFF TPASS
®
3-R by replacing the Accountability Key and then pressing both side buttons
simultaneously.
®
3-R can be reset to
Simultaneously press both side buttons
ACTIVATING TPASS®3-R: Simultanesouly press both
side buttons to activate TPASS®3-R into the motion
Sensing Mode.
During activation, an operational signal of escalating
audio tones will be heard and an alternating display of
yellow LEDs indicates the TPASS
Mode. When TPASS®3-R is activated, its internal radio
transmits signals that are received by the MX900.
PRE-ALERT MODE: After approximately 108 to 113
seconds of no motion, TPASS
Pre-Alert sound and the alternating yellow LED display
is interrupted by the pulsing of two red LEDs. The PreAlert sound progressively becomes louder, indicating
TPASS®3-R is closer to going into Alarm.
ALARM MODE: There are two methods of activating
the Alarm Mode.
Reset the Alarm Mode and return TPASS
Sensing Mode by simultaneously pressing both side
buttons.
TURN OFF: When in Sensing Mode, the TPASS
can be turned OFF by pressing both side buttons simultaneously.
Using an accountability key (w/ 6” tether) may help prevent accidental activation of the Emergency Alarm.
®
3-R to
®
3-R
Mode Selection
MANUAL ACTIVATION
● Simultanesouly press both side buttons to activate TPASS®3-R into the motion Sensing Mode.
ALARM
● Alarm Mode can be manually activated at any
time (from Sensing Mode or Off Mode) by
pressing the Emergency Alarm Button.
RESET
● When in Alarm, the TPASS
Sensing Mode by simultaneously pressing both
side buttons.
OFF
● When in Sensing Mode, the TPASS
turned OFF by pressing both side buttons simultaneously
®
3-R can be reset to
®
3-R can be
Visual / Audio Mode Display
OFF
● No LED display.
ON (Sensing Mode)
● A series of escalating, loud audio tones.
● Followed by yellow alternating LED display.
PRE-ALERT
● No motion sensed for 108 - 113 seconds.
● Yellow alternating LED display interrupted by the
pulsing of two red LEDs.
● Accompanied by progressively louder, sweeping
audio tones.
ALARM
● No motion sensed for 120 - 125 seconds.
● Rapid pulsing of two front red LEDs.
● Accompanied by a rapidly modulated, loud
(92dBA) audio alarm.
● Audio alarm signal is between 1,000 and 2,000
Hertz and cycles at 5.25 seconds on and .75 seconds off as an aid for determining direction when
personnel need assistance.
TPASS®3-R Maintenance
TPASS®3-R requires minimum maintenance and will
provide years of service.
Please Observe These Guidelines
● At the end of each use, clean unit with a damp cloth.
DO NOT use cleaning solvents.
● After each use, inspect unit for signs of physical
damage. Remove TPASS
physical damage is observed.
● Store TPASS
®
3-R in a dry, well ventilated area consistent with battery manufacturer requirements.
Recommended storage conditions are: 50
(10o to 25oC) at no more than 65% relative humidity.
● Units contaminated by chemical or radioactive materials must be disposed of or decontaminated in
accordance with all applicable regulatory standards.
● DO NOT mark or apply paint to TPASS
®
3-R from service if
o
to 77oF
®
3-R.
Specifi cations
Dimensions: 2-1/8” wide, by 2-1/4” deep (with clip),
4-1/8” high (with antenna)
Weight: 7.3 ounces with battery
Alarm Audio Output: approx. 92 dBA @ 10 feet
Case: rugged, high temperature, impact resistant,
translucent, Apache Yellow polycarbonate. .
Methods of Attachment: rugged Grip Clip and D-ring
for versatility in attaching to gear.
Antenna: short threaded antenna for easy replacement
Alarm Transmission: a 1.5 second burst of RF transmissions occurring every 4.5 seconds.
Battery: Intrinsically safe Lithium-ion.
Battery Life: estimated at 80 hrs in Sensing Mode and
4 to 6 hours in the Alarm Mode.
Battery Charging: 12VDC (std) or 120 VAC (optional
adapter required) may be used
Battery Charging Time: 6 to 8 hrs
Battery Charging Cycles: 500
Product Life: Approximately 3 to 5 years or longer, de-
pending on fi tness for use. Fitness for use is best de-
termined by the end user through a proper inspection
and maintenance program. Product should be retired
from service when damaged or returned to Grace Industries for evaluation and repair if applicable.
For TPASS®3 with Alarm Monitoring
The Alarm Monitoring feature allows personnel to
monitor the status of other personnel working in the
same general area, when they are equipped with
Grace Telemetry products. TPASS®3-AM MUST be in
the Sensing Mode to receive Alarm signals from other
Grace Telemetry products. When one telemetry unit
goes into “Alarm” and an Alarm Monitoring TPASS
receives the signal, the receiving TP3-AM will sound a
rapid ringing tone and provide a visual indication with
a fl ashing yellow LED at the base of the antenna. The
Alarm Monitoring display may be momentarily silenced
for one minute by pressing both side buttons simultaneously. Other units which go into alarm during the
one minute period will reactivate the Alarm Monitoring
audio sound signature and display. After one minute
if the original unit is still in alarm, the alarm monitoring feature and display will be reactivated. This cycle
will continue until the telemetry unit in Alarm is reset or
shut off. TPASS
®
3-AM has an orange case.
Limitations
To reduce risk of serious injury or loss of life,
ensure TPASS®3-R is fully operational by testing and
inspecting the unit prior to use. Use of a TPASS®3-R
maintenance and training program including
recharging exhausted or low batteries is required
for safe and proper use.
After charging battery, always test TPASS
MX900 to ensure proper operation.
If proper operation of TPASS
®
3-R is questionable,
remove unit from service and contact Grace Industries
for assistance.
The TPASS
®
3-R is Not available in a temperature
sensing model.
®
3-R with the
®
3
Loading...