GPX TD4221B User Manual

Download

Page 1

USER’S GUIDE

V:1635-0622-11

TD4221B

42” LCD HDTV + DVD

For the most up-to-date version of this User’s Guide, go to www.gpx.com

Page 2

Warnings and Precautions

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.

AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l’humidité.

CAUTION: Use of any controls or adjustments or performance of procedures other than those herein specied may result in hazardous radiation exposure.

WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

WARNING: Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging the surface. Use a protective barrier between the unit and surface to protect the surface.

WARNING: Use of this unit near uorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any uorescent lighting, as it may be the cause.

WARNING: Shock hazard - Do Not Open.

AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR

Mains Plug or Direct plug-in adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the Mains Plug or Direct plug-in adapter should be disconnected from the mains socket outlet completely.

La che d’alimentation ou adaptateur de courant est utilisé comme dispositif de déconnexion et doit rester accessible pendant l’utilisation. Pour mettre l’appareil hors tension, la che ou adaptateur de courant doit être débranché de la prise de courant.

Do not mix old and new batteries.

Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.

No mezcle baterías viejas y nuevas.

No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (ni-cad, ni-mh, etc.).

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

PRÉCAUTION: Danger d’explosion si les piles sont remplacées de façon incorrect. Remplacer les piles seulement par le même type de pile ou l’équivalent.

WARNING: The battery, batteries, and battery pack shall not be exposed to excessive heat such as sunshine, re, or the like.

WARNING: Lithium batteries, like all rechargeable batteries are recyclable and should be recycled or disposed of in normal household waste. Contact your local government for disposal or recycling practices in your area. They should never be incinerated since they might explode.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION

RISQUE D' ÉLECTROCUTION

NE PAS OUVRIR

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

This product utilizes a Class 1 laser to read Compact Discs. This laser Compact Disc Player is equipped with safety switches to avoid exposure when the CD door is open and the safety interlocks are defeated. Invisible laser radiation is present when the CD Player’s lid is open and the system’s interlock has failed or been defeated. It is very important that you avoid direct exposure to the laser beam at all times. Please do not attempt to defeat or bypass the safety switches.

Page 3

Important Safety Instructions

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12.

Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Special note: When placing your unit on a lacquered or natural nish, protect your furniture with a cloth or other protective material.

FCC Warnings

WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Additional Warnings

The apparatus shall not be exposed to dripping or splashing and that no objects lled with liquids, such as vases, shall be placed on apparatus.

L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet.

Battery shall not be exposed to excessive heat such as sunshine, re or the like.

Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la lumière du soleil, au feu ou autres choses de semblable.

Caution marking is located at the rear or bottom of the apparatus.

Attention marquage est situé sur le paneau arrière ou inférieur de l’unité.

The marking information is located at the rear or bottom of apparatus.

Le marquage est situé sur le paneau arrière ou inférieur de l’unité.

This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Rovi Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Rovi Corporation. Reverse engineering and disassembly are prohibited.

Customer Support: 1-888-999-4215 3

Page 4

42” LCD HDTV + DVD

Features

• 42” LCD display

• Aspect ratio: 16:9

• ATSC/NTSC tuner

• Resolution: 1920 x 1080

• V-chip

• Closed captioning

• Built-in stereo speakers

• Electronic program guide

• Sleep timer

• Multi-language on-screen display

• Component video input

• VGA PC video input

• Composite video input

* Please note, LCD panel specications are subject to change without notice.

* Some pixels may be visible on the screen, appearing as timy red, green, blue or black spots. This is normal and is

not a defect on the TV nor does it negatively aect the performance.

• RCA stereo audio inputs x 2

• Digital audio optical output

• RCA stereo output

• 3.5mm PC audio input

• RF input

• 3 HDMI inputs

• Full-function remote

• 42” LCD HDTV

• Built-in DVD Player

• 1080p

• Slot-load disc player

• USB port: supports JPEG, MP3 le formats and rmware updates

• AC power input

• Includes: remote control (2 AAA batteries included), removable stand

Includes

• AC power cable

• Remote control: requires 2 AAA batteries (included)

• Removable stand

• 7 screws

Setup

Power TV Stand

AC power input: requires an AC power cable (included)

Remote

Requires 2, AAA-size, batteries (included)

OPEN

Requires stand, 3 machine screw, and 4 self-tapping screws (all included)

1. Insert the stand into the bottom of the television.

2. Insert the machine screw into the topmost hole and tighten by hand using a philips-head screw driver.

3. Insert the self-tapping screws into the remaining 4 holes and tighten by hand using a philips-head screw driver.

Machine

Screws

Self-Tapping

Screws

Page 5

Table of Contents

42” LCD HDTV + DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Power Remote TV Stand Includes

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting a TV Antenna Connecting a Set-Top Box Auto Scanning for Channels Connecting Basic Cable

Channels, Favorites, and Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Channel List View Adding Favorites Viewing Favorites Setting the Clock

TV Menu and Parental Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Parental Controls (V-Chip) Television Menu

DVD and CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Loading a DVD or CD Playing a DVD or CD Programming a DVD or CD DVD Setup Menu

Connecting Other Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

(Set-Top Box, Gaming Device, DVD Player, or VCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting a Set-Top Box Connecting a Gaming Device Connecting a DVD Player or VCR

Connecting Other Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

(Computer and Optical Audio Output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting a Computer Using the Optical Audio Output

USB Thumb Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting a USB Thumb Drive Using a USB Thumb Drive Using the USB Service Port

Company Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

International Support Contact Information Green Initiative

Customer Support: 1-888-999-4215 5

Page 6

Introduction

Volume

Press to adjust

the volume.

Channel

Press to adjust

the television

channel.

Press to access

the television

menu.

Source

Press to adjust

the television

source.

Disc Slot

Repeat

Press to adjust

the repeat

settings for the

loaded disc.

Skip/Search

Press to skip

between

chapters or

tracks on a

loaded disc. Press and hold to fast forward

or rewind.

Eject

Press to eject

the loaded disc.

Play/Pause

Press to play or pause a loaded disc.

Stop

Press to stop a disc during play.

Press to power

Power

the television

o or on.

Page 7

Optical Audio

Output

VGA/PC

Video Input

HDMI Inputs

Component Video Input

RCA Audio

Input 2

AC Power

Input

Antenna Input 3.5mm PC

Audio Input

USB Port Composite

Video Input

RCA Audio

Input 1

RCA Audio

Output

Customer Support: 1-888-999-4215 7

Page 8

Press to power the television o or on.

POWER

NUMBER KEYPAD

MUTE

Press to mute the volume.

Press to adjust the aspect ratio between

ASPECT

WIDE, CINEMA, ZOOM, and NORMAL.

SLEEP

Press repeatedly to set the sleep timer.

After the set time has expired the

television will automatically power o.

PICTURE

Press to adjust the picture between

STANDARD, MOVIE, USER, and DYNAMIC.

The user mode can be customized by

accessing Picture Settings in the menu.

SOUND

Press to adjust the sound between

STANDARD, SOFT, USER, and DYNAMIC.

The user mode can be customized by

accessing Sound Settings in the menu.

VOLUME ±

Press to adjust the volume.

Press to view the television setup menu.

AUDIO/SAP

Press adjust the current audio

settings for the loaded DVD. In TV

mode, press to switch to an alternate

audio option when supported.

ADD/ERASE/STOP

In TV mode, press to add or erase

the current channel as a favorite.

Press to stop a disc during play.

FREEZE

Press to freeze or unfreeze the current frame in TV mode.

EJECT/GUIDE

Press to eject a loaded disc. In TV mode, press to view the onscreen television guide.

ANGLE/PREV

Press to view alternate angles on supported DVDs. In TV mode, press to switch to the previous channel.

SUBTITLE/CC

Press to adjust the current subtitle settings for the loaded DVD. In TV mode, press to turn closed captioning o or on.

CHANNEL ±

Press to adjust the television channel.

EXIT

Press to exit the current on-screen menu.

ARROWS/ENTER

Press to make selections in the on screen or disc menus.

ZOOM

Press to zoom in or out on a loaded DVD.

FAV CH ±

Press to cycle through saved favorite channels in TV mode.

In PC mode, press to ne tune the

AUTO

screen position automatically.

FAV LIST/PLAY/PAUSE

In TV mode, press to view your favorites

list. Press to play or pause a loaded disc.

DISPLAY

Press to view the on-screen display.

CH LIST

In TV mode, press to view a

list of available channels.

SKIP

Press to skip between chapters

or tracks on a loaded disc.

WIDE

Press to switch between 4:3

LB, 4:3 PS, and 16:9.

PROG

Press to program a loaded

disc to play titles, chapters, or

tracks in a specied order.

DVD SETUP

Press to access the DVD setup menu.

GOTO

Press to go to a specied title, chapter, track, or time on the loaded disc.

SOURCE

Press and use the ARROW KEYS/ ENTER buttons to adjust the source.

REW/F FWD

Press to search through an individual chapter or track.

TITLE

Press to access the title menu on a loaded DVD.

DVD MENU

Press to access the loaded DVD’s menu.

A-B

Press to create a repeating loop on a specied section of a loaded DVD.

REPEAT

Press to repeat a title, chapter, track, or entire disc.

USB

Press to access Media mode.

Page 9

Setup

Connecting a TV Antenna

Requires a TV antenna (not included).

1. Connect a VHF, UHF, or HDTV antenna to the RF INPUT on the television.

2. Press the SOURCE button to switch to TV mode.

3. Press the MENU button to access the setup menu.

4. Press the ARROW () buttons to highlight the CHANNEL icon. Press the ENTER button.

5. Press the ARROW () buttons to highlight SIGNAL TYPE. Press the ARROW () buttons to select AIR.

6. Press the ARROW () buttons to highlight AUTO CHANNEL SEARCH. Press the ENTER button to begin scanning for available channels.

Connecting a Set-Top Box

Requires a Set-Top Box (not included).

Connecting Basic Cable

Requires a cable connection.

1. Connect a cable to the RF INPUT on the television.

2. Press the SOURCE button to switch to TV mode.

3. Press the MENU button to access the setup menu.

4. Press the ARROW () buttons to highlight the CHANNEL icon. Press the ENTER button.

5. Press the ARROW () buttons to highlight SIGNAL TYPE. Press the ARROW () buttons to select CABLE.

6. Press the ARROW () buttons to highlight AUTO CHANNEL SEARCH. Press the ENTER button to begin scanning for available channels.

If your Set-Top Box has an HDMI Output:

• Connect the HDMI output on the Set-Top Box to one of the HDMI INPUTS on the television using an HDMI cable (not included).

If your Set-Top Box has a Composite Video Output:

• Connect the video output on the Set-Top Box to the COMPOSITE VIDEO INPUT on the television using an A/V RCA cable (not included). Connect the audio output on the Set-Top Box to the RCA AUDIO INPUT on the television.

If your Set-Top Box has a Component Video Output:

• Connect the component video output on the Set-Top Box to the COMPONENT VIDEO INPUT on the television using a component RCA cable (not included). Connect the audio output on the Set-Top Box to the RCA AUDIO INPUT on the television.

After connecting your Set-Top Box:

• Press the SOURCE button to switch to YPbPr, AV, or HDMI 1, 2, or 3 to match the connection used.

Auto Scanning for Channels

The Auto Channel Scan must be run before any channels can be viewed on the television.

1. Press the SOURCE button to switch to TV mode.

2. Press the MENU button to access the setup menu.

3. Press the ARROW () buttons to highlight the CHANNEL icon. Press the ENTER button.

4. Press the ARROW () buttons to highlight SIGNAL TYPE. Press the ARROW () buttons to select AIR.

5. Press the ARROW () buttons to highlight AUTO CHANNEL SEARCH. Press the ENTER button to begin scanning for available channels.

Customer Support: 1-888-999-4215 9

Page 10

Channels, Favorites, and Clock

Channel List View

1. Press the SOURCE button to switch to TV mode.

2. Press the CH LIST button, on the remote, to view a list of available channels.

Unless you are using a Set-Top Box, you must auto scan for channels before being able to view channels in list view.

Adding Favorites

1. Press the SOURCE button to switch to TV mode.

2. Press the CHANNEL buttons to select the desired TV channel.

3. Press the ADD/ERASE button to add or erase the current channel as a favorite.

Viewing Favorites

1. Press the SOURCE button to switch to TV mode.

2. Press the FAV LIST button to view a list of your saved favorites.

Setting the Clock

1. Press the MENU button to access the setup menu.

2. Press the ARROW () buttons to highlight the SETUP icon. Press the ENTER button.

3. Press the ARROW () buttons to highlight CLOCK. Press the ENTER button.

4. Press the ARROW () buttons to highlight TIME ZONE. Press the ARROW () buttons to select your current time zone.

5. Press the ARROW () buttons to highlight AUTO CLOCK. Press the ARROW () buttons to turn auto clock o and on.

When the correct time zone is set, auto clock will automatically set your clock and date for you.

6. To set the time and date manually, turn auto clock o, highlight SETUP TIME, and use the ARROW and ENTER buttons to manually set the time and date.

Page 11

TV Menu and Parental Controls

Parental Controls (V-Chip)

1. Press the SOURCE button to switch to TV mode.

2. Press the MENU button.

3. Press the ARROW () buttons, highlight PARENTAL, and press the ENTER button.

4. The default passcode for the parental lock is:

0 0 0 0

5. Enter the passcode to access the PARENTAL CONTROL preferences.

6. From this menu, you can lock specic ratings from the United States rating system or the Canadian rating system by accessing the V-CHIP settings. You can also lock the buttons on the television or lock specic sources from access.

Television Menu

Press the MENU button to access the TV menu. Press the EXIT button to exit the TV menu.

Picture

Picture Settings Screen Size PC Settings Color Temperature Advanced Picture Settings

Sound

Sound Settings Surround Mode Analog Sound Digital Sound Other Settings

Channel

Channel List Favorite List Channel Setting Signal Type Auto Channel Search

Setup

Closed Caption Menu Language Clock

Others

Blue Back No Signal Power O No Operation Power O All Reset Audio Only

Parental

Lock Parental Control V-Chip Change Password Keypad Lock Source Lock

Customer Support: 1-888-999-4215 11

Page 12

DVD and CD

Loading a DVD or CD

1. Insert a DVD or CD into the slot-load disc drive, with the label side of the DVD or CD facing the back of the television.

Once a DVD or CD is loaded into the television, the TV will automatically switch to DVD mode.

Playing a DVD or CD

1. Follow the instructions for Loading a DVD or CD.

2. After the DVD or CD is loaded, it will begin playing automatically.

If the DVD or CD does not begin playing automatically, press the PLAY/PAUSE button to begin playing the loaded disc.

•

Programming a DVD or CD

1. While a DVD or CD is playing, press the PROGRAM button on the remote.

2. Using the NUMBER KEYPAD enter in the title (T) and chapters (C), or tracks in the order you want them to play.

3. Highlight the on-screen PLAY button using the ARROW buttons and press the ENTER button.

4. The programmed titles and chapters, or tracks will now play in the designated order.

5. To cancel a program, press the PROGRAM button, highlight the on-screen CLEAR button using the ARROW buttons, and press the ENTER button.

DVD Setup Menu

In DVD mode, press the DVD SETUP button to access the DVD setup menu. Press the DVD SETUP button to exit the DVD setup menu.

System Setup

TV System Screen Saver TV Type Power Resume Default

Exit Setup

Language Setup

OSD Language Audio Language Subtitle Language Menu Language

Exit Setup

Key Setup

Key

Exit Setup

Audio Setup

Dynamic Range Dual Mono Exit Setup

Page 13

Connecting Other Devices

HDMI HDMI HDMI

(Set-Top Box, Gaming Device, DVD Player, or VCR)

Connecting a Set-Top Box

You will need: a set-top box, composite and RCA stereo cables or component and RCA stereo cables or an HDMI cable. (not included)

1. Connect the set-top box’s audio and video outputs to the corresponding audio and video inputs on the television.

2. Power the television on and press the SOURCE button to switch to the connected input. (AV (composite), YPbPr (component), or HDMI 1, 2, or 3)

Connecting a Gaming Device

You will need: a gaming device, composite and RCA stereo cables or component and RCA stereo cables or an HDMI cable. (not included)

1. Connect the gaming device’s audio and video outputs to the corresponding audio and video inputs on the television.

COMPOSITE and RCA STEREO

COMPONENT and RCA STEREO

2. Power the television on and press the SOURCE button to switch to the connected input. (AV (composite), YPbPr (component), or HDMI 1, 2, or 3)

Connecting a DVD Player or VCR

You will need: a DVD player or VCR, composite and RCA stereo cables or component and RCA stereo cables or an HDMI cable. (not included)

1. Connect the DVD player or VCR’s audio and video outputs to the corresponding audio and video inputs on the television.

2. Power the television on and press the SOURCE button to switch to the connected input. (AV (composite), YPbPr (component), or HDMI 1, 2, or 3)

HDMI

Customer Support: 1-888-999-4215 13

Page 14

Connecting Other Devices

(Computer and Optical Audio Output)

Connecting a Computer

You will need: a PC with a VGA output, and a VGA cable. (not included)

1. Connect the computer’s VGA output to

the VGA/PC INPUT on the television.

2. Power the television on and press the

SOURCE button to switch to the PC Mode.

3. Audio from the connected PC can be input to the television through the TV’s PC AUDIO INPUT by using a 3.5mm audio cable (not included).

Using the Optical Audio Output

You will need: a (home theater) with an Optical Audio Input and a Digital Optical Audio Cable (not included)

1. Connect the Digital Optical Audio Cable to the (home theater system) and the television.

2. Adjust the settings on your (home theater) to play audio from the connected Optical Audio Input.

VGA/PC INPUT and PC AUDIO INPUT

OPTICAL AUDIO OUTPUT

Please note: home theater systems may label the Optical Audio Input source dierently, such as “PCM”, or “Digital Audio Input”. Please consult your home theater system’s user manual in order to select the correct input source.

3. Audio from the television will now be played through the connected (home theater system).

Page 15

USB Thumb Drive

Connecting a USB Thumb Drive

1. Load a USB thumb drive into the USB PORT as shown in the image to the right.

Using a USB Thumb Drive

1. Follow the instructions for Connecting a USB thumb drive.

2. Press the SOURCE button or the USB button on the remote to switch to Media mode.

3. Use the ARROW and ENTER buttons to select and play content from the connected USB thumb drive.

4. Press the EXIT button to return to the media menu.

The USB port can also be used to upgrade the televisions rmware. For detailed instructions and the latest software, go to www.gpx.com

Using the USB Service Port

The USB Service Port is used for rmware upgrades to the television.

1. Firmware upgrades that are available for the television can be downloaded from www.gpx.com

USB PORT

Customer Support: 1-888-999-4215 15

Page 16

GPX TD4221B User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual