GPX TD2420 User Manual

Download

Page 1

USER’S GUIDE

V:1058-0914-09

TD2420 24” Class LCD Television

For the most up-to-date version of this User’s Guide, go to www.gpx.com

Page 2

WARNINGS AND PRECAUTIONS

• CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• WARNING: To prevent re or shock hazards, do not expose this unit

to rain or moisture.

• AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l’humidité.

• CAUTION: Use of controls or adjustments or performance of procedures other than those specied may result in hazardous radiation exposure.

• WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• WARNING: Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging the surface. Use a protective barrier between the unit and surface to protect the surface.

• WARNING: Use of this unit near uorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any uorescent lighting, as it may be the

cause.

• CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• PRÉCAUTION: Danger d’explosion si les piles sont remplacées de façon incorrect. Remplacer les piles seulement par le même type de pile ou l’équivalent.

• WARNING: There is a danger of explosion if you attempt to charge standard Alkaline batteries in the unit. Only use rechargeable NiMH batteries.

• WARNING: The remote control’s button cell battery contains mercury. Do not put in the trash, instead recycle or dispose of as hazardous waste

• WARNING: Lithium batteries, like all rechargeable batteries are recyclable and should be recycled or disposed of in normal household waste. Contact your local government for disposal or recycling practices in your area. They should never be incinerated since they might explode.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

This product utilizes a Class 1 laser to read Com-

pact Discs. This laser Compact Disc Player is

equipped with safety switches to avoid exposure when the CD door is open and the safety interlocks are defeated. Invisible laser radiation is present when the CD Player’s lid is open and the system’s interlock has failed or been defeated. It is very important that you avoid direct exposure to the laser beam at all times. Please do not attempt to defeat or bypass the safety switches.

Main plug is used as disconnect device and it should remain readily operable during intended use.

Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.

No mezcle baterías viejas y nuevas. No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (ni-cad, ni-mh, etc.).

IMPORTANT SAFETY INSTRUCTIONS

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding - type

plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly

at plugs, convenience receptacles, and the point where they exit from

the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specied by the

manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

GPX | TD24202

Page 3

FCC Warnings

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and re-

ceiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Additional Warnings

• The apparatus shall not be exposed to dripping or splashing

and that no objects lled with liquids, such as vases, shall be placed on apparatus.

L’appareil ne doit pas être exposé aux écoulements ou aux

éclaboussures et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet.

• Main plug is used as disconnect device and it should remain

readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected form the mains socket outlet com-

pletely.

La prise du secteur ne doit pas être obstruée ou doit être

facilement accessible pendant son utilisation. Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être débranchée du secteur.

• Battery shall not be exposed to excessive heat such as sun-

shine, re or the like.

Les piles ne doivent pas être exposées à de forte chaleur, tel

qu’à la lumière du soleil, au feu ou autres choses de semblable.

• Caution marking is located at the rear of the apparatus.

Les marquages sont inscrits de derrière de l’appareil.

• The marking information is located at the rear of apparatus.

Les précautions d’emploi sont inscrites de derrière de

l’appareil.

CUSTOMER HELPLINE | 1-314-621-2881 GPX | TD2420 3

Page 4

24” CLASS LCD TELEVISION

Features

24” Class LCD TV

This 24” class TV has an actual diagonal viewing dimension of 23.6”.

• Built-In ATSC Tuner

• Electronic Program Guide (EPG)

• Supports 480i, 480p, 720p, 1080i, 1080p

• Aspect Ratio: 16:9

• Display Resolution: 1920x1080, Viewing Angle: 170(H)x160(V)

• Contrast: 1000:1, Brightness: 300cd/m

• Response Time: 5ms, Color: max 16.7M

• Multi-Language OSD: On-Screen Display in English,

French & Spanish

• Adjustable Sleep Timer

Slot-Load DVD/CD Player

• Plays DVD, DVD±R/RW, JPEG Picture Discs

• Plays Audio CD, CD-R/RW Discs

• UpConversion to Screen Resolution

Included

Connections

• Expansion Memory SD Card Slot

• USB Jack for Thumb Drives

• A/V Input, RCA type

• RF Input for Tuner

• VGA Input

• PC Audio Input

• HDMI Input

Built-In Speakers

Full-Feature Remote Control

• Battery included

AC-Powered

• Built-In 120V AC Line Cord

• TD2420

• Removable stand

• Remote control, remote batteries included

GPX | TD24204

Page 5

TABLE OF CONTENTS

INTRODUCTION

SETUP

TELEVISION SETUP

TELEVISION

DVD & CD

OTHER CONNECTIONS

USB THUMB DRIVE

MMC/SD/MS MEMORY CARD

COMPANY INFORMATION

CUSTOMER HELPLINE | 1-314-621-2881 GPX | TD2420 5

Page 6

INTRODUCTION

POWERSOURCE CHANNEL EJECT

PLAY/ PAUSE

VOLUMEMENU

Press to view the

setup menu for the

television.

SOURCE

Press to switch the

current Source.

(TV, AV, DVD,

HDMI, VGA)

LCD DISPLAY

24” Class LCD

Display

REMOTE

RECEIVER

REMOVABLE TV

STAND

CHANNEL

Press to change

the LCD televisions

channel.

VOLUME

Press to adjust the

volume.

PLAY/PAUSE

Press to play or pause a loaded

DVD or CD.

EJECT

Press to eject a

DVD or CD from

the slot-load disc

drive.

POWER

Press to turn the LCD television off or on.

TV ANTENNA

INPUT

AUDIO INPUT

COMPOSITE

VIDEO INPUT

3.5MM PC AUDIO INPUT

PC VIDEO INPUT

HDMI INPUT

DVD/CD LABEL SIDE

ANTENNA

AUDIO IN

VIDEO

VIDEO IN

PC AUDIO

PC IN

HDMI

ONLY

SERVIC E

THUMB DRIVE

SD/MMC/MS

SLOT-LOAD DISC DRIVE

USB THUMB DRIVE CONNECTION

SD/MMC/MS MEMORY CARD SLOT

GPX | TD24206

Page 7

Press to turn the LCD television

POWER

off or on.

PLAY/PAUSE

Press to play or pause a loaded

DVD or CD.

Press to search forwards or

backwards through the current

chapter or track.

P MODE

Press to switch between avail-

able Picture Modes. (Standard,

Dynamic, Soft, Personal)

S MODE

Press to switch between available Sound Modes. (Standard,

Music, Movie, Personal)

LIST

Press to view a list of all

available television channels.

FAV

Press to view a list of favorite

channels as added through the

setup menu.

SOURCE

Press to switch the current

Source.

(TV, AV, DVD, HDMI, VGA)

Press to view the setup menu

for the television.

NUMBER KEYPAD

VOLUME

Press to adjust the volume.

ASPECT

Press to adjust the current

aspect of the display. (Normal,

Wide, Zoom, Cinema)

DVD DISPLAY

Press to view the on-screen

display for a DVD, CD, USB

Thumb Drive, or Memory Card.

ZOOM

Press to zoom in or out on a

loaded DVD.

GOTO

Press and enter in a specic

title, chapter, track, or time to

go to.

ANGLE

Press to view different angles

on a supported DVD.

POWER

P MODE

LIST

SOURCE

VOLUME

GOTO

S MODE

FAV

ASPECT

ZOOMDVD DISPLAY

ANGLE

DVD MENUDVD SETUP

ENTER

MTS

GUIDE

+10

SLEEP

AUDIO

A-B

TITLE

MUTE

V-CHIP

DISPLAY

EXIT

PROG

CHANNEL

SUBTITLE

REPEAT

EJECT

STOP

Press to stop a DVD or CD during play.

MUTE

Press to mute the volume.

SKIP

Press to skip forwards or backwards through chapters and tracks.

Press to adjust the Closed Captioning settings.

MTS

Press to adjust between available audio channels.

V-CHIP

Press and enter the passcode to unlock the current channel’s parental lock. (default passcode: 0000)

GUIDE

Press to view an on-screen programming guide.

DISPLAY

Press to view the on-screen display for the LCD television.

DIRECTION () / ENTER

Press to navigate and make selections.

EXIT

Press to exit the current onscreen display or menu.

PROG/PREV

Press to program a DVD or CD to play chapters and titles or

tracks in a specied order. In

TV mode, press to go to the previous channel.

SLEEP

Press repeatedly to set the sleep timer. After the set sleep time has expired the LCD television will power off.

CHANNEL

Press to change the LCD televisions channel.

AUDIO

Press to cycle through available audio options for the loaded DVD.

SUBTITLE

Press to cycle through available subtitle options for the loaded DVD.

Press to enter the DVD setup

DVD SETUP

menu.

DVD MENU

Press to access the main menu

of a loaded DVD.

TITLE

Press to access the title menu

of a loaded DVD.

A-B

Press to set a specied section

of DVD to play repeatedly.

REPEAT

Press to repeat the current chapter, title, track, or album on a DVD or CD.

EJECT

Press to eject a DVD or CD from the slot-load disc drive.

Page 8

SETUP

Power

Plug the attached AC cord into a standard AC power outlet to power the LCD television.

Remote Power

Requires 2 AAA batteries, included. Insert the included AAA batteries into the

remote control to power the remote.

GPX | TD24208

Page 9

TELEVISION SETUP

Connecting a TV Antenna

Requires a TV antenna, not included. 1 Connect a VHF, UHF, or HDTV antenna to the

TV ANTENNA on the LCD television.

2 Press the SOURCE button and adjust the

INPUT SOURCE to “TV”.

3 Press the MENU button to access the

Setup Menu.

4 Press the DIRECTION () buttons to

select the CHANNEL tab.

5 Press the DIRECTION () buttons to

select AIR/CABLE. Press the DIRECTION () buttons to select AIR.

6 Press the DIRECTION () buttons

to select AUTO SCAN. Press the ENTER button.

7 Press the DIRECTION () buttons to

select START TO SCAN. Press the ENTER button.

Connecting a Set-Top Box

Requires a Set-Top Box, not included.

If your Set-Top Box has an HDMI Output:

1 Connect the HDMI Output on the Set-

Top Box to the HDMI INPUT on the LCD television.

If your Set-Top Box has an Video Output:

1 Connect the Video Output on the Set-

Top Box to the COMPOSITE VIDEO INPUT on the LCD television. Connect the Audio Output on the Set-Top Box to the AUDIO INPUT on the LCD television.

After connecting your Set-Top Box:

2 Press the SOURCE button and adjust

the INPUT SOURCE to “VIDEO” or “HDMI” to match the connection.

Connecting Basic Cable

Because the LCD television is HDTV only, basic cable can only be connected through a settop box. Requires a basic cable connection and set-top box, not included.

1 Follow the instructions for connecting a

set-top box.

SET-TOP BOX

HDMI

Scanning for Channels

After connecting your TV Antenna or Basic Cable you need to scan for channels before you’ll be able to watch any television.

1 Connect a TV Antenna or Basic Cable to

the LCD television.

2 Press the SOURCE button and adjust the

INPUT SOURCE to “TV”.

3 Press the MENU button to access the

Setup Menu.

4 Press the DIRECTION () buttons to

select the CHANNEL tab.

5 Press the DIRECTION () buttons

to select AUTO SCAN. Press the ENTER button.

6 Press the DIRECTION () buttons to

select START TO SCAN. Press the ENTER button.

Your LCD television will automatically begin scanning for available channels.

NTSC analog channels will not be scanned.

CUSTOMER HELPLINE | 1-314-621-2881 GPX | TD2420 9

Page 10

TELEVISION

Channel List View

1 Press the SOURCE button and adjust the

INPUT SOURCE to “TV”.

2 Press the LIST button, on the remote, to

view a list of available channels.

Unless you are using a Set-Top Box, you must auto scan for channels before being able to view channels in list view.

Adding Favorites

1 Press the SOURCE button and adjust the

INPUT SOURCE to “TV”.

2 Press the MENU button to access the

Setup Menu.

3 Press the DIRECTION () buttons to

select the CHANNEL tab.

4 Press the DIRECTION () buttons to

select FAVORITES. Press the ENTER button.

Parental Controls (V-Chip)

1 Press the SOURCE button and adjust the

INPUT SOURCE to “TV”. 2 Press the MENU button. 3 Press the DIRECTION () buttons,

select LOCK, and press the ENTER button. 4 The default passcode for the parental lock

is: 0 0 0 0 5 Enter the passcode to access the LOCK

preferences. 6 From this menu, you can lock specic

ratings from the United States rating

system or the Canadian rating system by

turning the SYSTEM LOCK to ON. 7 Press the V-CHIP button on the remote

and enter the passcode to unlock the

current channel when browsing television

channels.

5 Press the DIRECTION () buttons to

select available channels and press the ENTER button to save those channels as favorites.

Channels added to the Favorites list will show a check next to their name.

Viewing Favorites

1 Press the SOURCE button and adjust the

INPUT SOURCE to “TV”.

2 Press the FAV button, on the remote, to

view a list of channels saved as favorites.

3 Press the DIRECTION () and ENTER

buttons on the remote to highlight and select a channel to go to.

Miscellaneous

Ideal display refresh rate: 60Hz

GPX | TD242010

Page 11

DVD & CD

Loading and Playing a DVD or CD

Loading a DVD or CD:

1 Press the SOURCE button and adjust the

INPUT SOURCE to “DVD”.

2 Gently insert a DVD or CD into the slot-

load disc drive, with the label side of the DVD or CD facing the back of the LCD television.

Playing a DVD or CD:

3 After the DVD or CD is loaded, it should

begin playing automatically.

4 If the DVD or CD does not begin playing

automatically, press the PLAY/PAUSE button.

Programming a DVD or CD

1 While a DVD or CD is playing, press the

PROGRAM button on the remote.

2 Enter in the title (T) and chapters (C), or

tracks in the order you want them to play.

3 Highlight the on-screen PLAY button using

the DIRECTION () buttons, and press the ENTER button.

4 The programmed titles and chapters, or

tracks will now play in the designated order.

5 To cancel a program, press the PROGRAM

button, highlight the on-screen CLEAR button using the DIRECTION () buttons, and press the ENTER button.

CUSTOMER HELPLINE | 1-314-621-2881 GPX | TD2420 11

Page 12

OTHER CONNECTIONS

HDMI

PC IN

ANTENNA

VIDEO

AUDIO IN

VIDEO IN

PC AUDIO

SERV ICE

ONLY

HDMI

PC IN

ANTENNA

VIDEO

AUDIO IN

VIDEO IN

PC AUDIO

SERV ICE

ONLY

HDMI

Connecting a Gaming Console

Requires a RCA Audio/Video cable or a HDMI cable, not included.

VIDEO:

1 Plug the RCA video cable or the HDMI

cable into the RCA video output or HDMI output on a gaming console and the VIDEO INPUT or HDMI INPUT on the LCD television.

AUDIO:

2 Connect the RCA audio cables to the

audio output on a gaming console and the

AUDIO INPUT on the LCD television.

Connecting a PC

Requires a VGA cable, not included. 1 Power the LCD television on and press the

SOURCE button to switch to VGA mode.

VIDEO:

2 Plug the VGA cable into the VGA output

on a computer and the PC IN on the LCD television.

3 The connected computer should

automatically recognize the LCD television as an additional monitor.

AUDIO:

4 If your computer has an audio output, it

can be connected to the PC AUDIO INPUT on the LCD television. This will allow audio from your connected computer to play through the LCD television’s speakers.

Advanced PC Options

1 Power the LCD television on and press the

2 Press the MENU button. 3 Press the DIRECTION () buttons to

SOURCE button to switch to VGA mode.

select SETUP. Press the ENTER button.

4 Press the DIRECTION () buttons to

select ADVANCED. Press the ENTER button.

5 Press the DIRECTION () buttons

to adjust the following screen options.

GPX | TD242012

H-POS

Use to adjusts the horizontal position of the screen.

V-POS

Use to adjusts the vertical position of the screen.

CLOCK

Use to prolong the image on the screen.

PHASE

Use to adjust the denition of the screen.

Page 13

USB THUMB DRIVE

DVD/CD LABEL SIDE

SD/MMC/MS

THUMB DRIVE

Connecting a USB Thumb Drive

1 Plug a USB Thumb Drive into the THUMB

DRIVE CONNECTION on the side of the

LCD television.

2 Press the POWER button to turn the LCD

television on.

3 Press the SOURCE button to switch to DVD

mode.

4 Press the DVD SETUP button on the

remote.

5 Press the DIRECTION () buttons,

select SOURCE, and press the ENTER button.

6 Press the DIRECTION () buttons,

select USB, and press the ENTER button.

7 Press the DVD SETUP button to exit the

DVD setup menu.

Playing Media from a USB Thumb Drive

1 Press the DIRECTION () and

ENTER buttons to select an audio le,

image le, or a video le.

File Compatibilty:

AUDIO:

Audio Files

IMAGES: JPG (Max Size: 1280X1024px) VIDEO: MPEG-2

CUSTOMER HELPLINE | 1-314-621-2881 GPX | TD2420 13

Page 14

MMC/SD/MS MEMORY CARD

DVD/CD LABEL SIDE

SD/MMC/MS

THUMB DRIVE

MMC

Connecting a Memory Card

1 Insert the memory card into the SD/MC/

MMC slot on the side of the LCD television.

2 Press the POWER button to turn the LCD

television on.

3 Press the SOURCE button to switch to DVD

mode.

4 Press the DVD SETUP button on the

remote.

5 Press the DIRECTION () buttons,

select SOURCE, and press the ENTER button.

6 Press the DIRECTION () buttons,

select CARD, and press the ENTER button.

7 Press the DVD SETUP button to exit the

DVD setup menu.

Playing Media from a Memory Card

1 Press the DIRECTION () and

ENTER buttons to select an audio le,

image le, or a video le.

File Compatibilty:

AUDIO:

Audio Files

IMAGES: JPG (Max Size: 1280X1024px) VIDEO: MPEG-2

GPX | TD242014

Page 15

CUSTOMER HELPLINE | 1-314-621-2881 GPX | TD2420 15

Page 16

GPX TD2420 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual