GPX TD1920 User Manual

Download

Page 1

USER’S GUIDE

V:1523-1103-10

For the most up-to-date version of this User’s Guide, go to www.gpx.com

TD1920

19” HDTV with DVD

Page 2

GPX2

• WARNING:Lithium batteries, like all rechargeable batteries are recyclable and should be recycled or disposed of in normal household waste. Contact your local government for disposal or recycling practices in your area. They should never be incinerated since they might explode.

• WARNING: Shock hazard - Do Not Open.

• AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR

Mains plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected form the mains socket outlet completely.

La prise du secteur est utilisé pour déconnecter le système. La prise du secteur ne doit pas être obstruée ou doit être facilement accessible pendant son utilisation. Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être débranchée du secteur.

Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.

No mezcle baterías viejas y nuevas. No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (ni-cad, ni-mh, etc.).

• CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• WARNING:To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.

• AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l’humidité.

• CAUTION: Use of controls or adjustments or performance of procedures other than those specied may result in hazardous radiation exposure.

• WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• WARNING: Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging the surface. Use a protective barrier between the unit and surface to protect the surface.

• WARNING: Use of this unit near uorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any uorescent lighting, as it may be the cause.

• CAUTION:Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• PRÉCAUTION: Danger d’explosion si les piles sont remplacées de façon incorrect. Remplacer les piles seulement par le même type de pile ou l’équivalent.

• WARNING: There is a danger of explosion if you attempt to charge standard Alkaline batteries in the unit. Only use rechargeable NiMH batteries.

• WARNING: The remote control’s button cell battery contains mercury. Do not put in the trash, instead recycle or dispose of as hazardous waste

The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

ATTENTION

RISQUE D' ÉLECTROCUTION

NE PAS OUVRIR

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

This product utilizes a Class 1 laser to read Compact Discs. This laser Compact Disc Player is equipped with safety switches to avoid exposure when the CD door is open and the safety interlocks are defeated. Invisible laser radiation is present when the CD Player’s lid is open and the system’s interlock has failed or been defeated. It is very important that you avoid direct exposure to the laser beam at all times. Please do not attempt to defeat or bypass the safety switches.

Warnings and Precautions

Page 3

Customer Support: 1-888-999-4215 GPX 3

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• The apparatus shall not be exposed to dripping or splashing and

that no objects lled with liquids, such as vases, shall be placed on apparatus.

L’appareil ne doit pas être exposé aux écoulements ou aux

éclaboussures et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet.

• Main plug is used as disconnect device and it should remain

readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected form the mains socket outlet completely.

La prise du secteur ne doit pas être obstruée ou doit être

facilement accessible pendant son utilisation. Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être débranchée du secteur.

• Battery shall not be exposed to excessive heat such as sunshine,

re or the like.

Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à

la lumière du soleil, au feu ou autres choses de semblable.

• Caution marking is located at the rear or back of the apparatus.

Attention marquage est situé à l’arrière ou à l’arrière de

l’appareil

• The marking information is located at the rear or back of

apparatus.

Les informations de marquage est situé à l’arrière ou à l’arrière

de l’appareil.

FCC Warnings

Additional Warnings

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12.

This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts.

Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Important Safety Instructions

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Rovi Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Rovi Corporation. Reverse engineering and disassembly are prohibited.

Page 4

• 19” LCD TV

• ATSC/NTSC tuner

• Electronic program guide

• TV supports: 480p, 480i, 720p, 1080p, 1080i

• Display resolution: 1366x768

• Viewing Angle: 170(H)x160(V)

• Contrast: 1000:1

• Brightness: 300cd/m

• Response time: 8ms

• Color: max 16.7M

• Multi-Language OSD

• Sleep timer

• DVD player: DVD, DVD±R/RW

• CD player: CD, CD-R/RW, JPEG

• Upconversion to screen resolution

• Memory card slot

• USB port 2.0, high speed

• A/V input, RCA type

• RF input for tuner

• VGA/PC input

• HDMI input

• Built-In speakers

• Remote control: requires 2, AAA size, batteries (included)

• AC power: requires an AC power cable (included)

• Remote control: requires 2, AAA size, batteries (included)

• Removable stand: requires 3 screws (included)

Features Included

19” HDTV with DVD

GPX4

Page 5

Customer Support: 1-888-999-4215 GPX 5

TABLE OF CONTENTS

Warnings and Precautions . . . . . . . . . . 2

Important Safety Instructions . . . . . . . . . 3

• FCC Warnings

• Additional Warnings

19” HDTV with DVD . . . . . . . . . . . . 4

• Features

• Included

Introduction . . . . . . . . . . . . . 6

Setup . . . . . . . . . . . . . . . 8

• Power

• Remote

• TV Stand

Television Setup . . . . . . . . . . . . 9

• Connecting a TV Antenna

• Connecting a Set-Top Box

• Connecting Basic Cable

Television . . . . . . . . . . . . . 10

• Auto Scanning for Channels

• Channel List View

• Adding Favorites

• Viewing Favorites

• Parental Controls (V-Chip)

Television . . . . . . . . . . . . . 11

• Setting the Clock

• Television Menu

DVD and CD . . . . . . . . . . . . 12

• Loading a DVD or CD

• Playing a DVD or CD

• Programming a DVD or CD

• DVD Setup Menu

USB Port and Memory Card Reader . . . . . . . 13

• Connecting a Memory Card

• Using a Connected Memory Card

• Connecting a USB Thumb Drive

• Using a Connected USB Thumb Drive

Connecting Other Devices (Set-Top Box, Gaming Device, DVD

Player, VCR, or PC) . . . . . . . . . . . 14

• Connecting a Set-Top Box

• Connecting a Gaming Device

• Connecting a DVD Player or VCR

• Connecting a Computer

Company Information . . . . . . . . . . 16

• Green Initiative

• International Support

• Contact Information

Page 6

Press to access the television menu.

POWER

Press to power the television o or on.

SOURCE

Press to adjust the television source.

HDMI INPUT

VGA/PC INPUT

PC AUDIO INPUT

S-VIDEO INPUT

COMPOSITE VIDEO INPUT

COMPONENT VIDEO INPUT

RCA AUDIO INPUT

RF INPUT

STEREO HEADPHONE JACK

Introduction

VOLUME

Press to adjust the

volume.

CHANNEL

Press to adjust the

television channel.

DISC DRIVE

USB PORT

SD/MMC/MS

MEMORY CARD

READER

PLAY/PAUSE

Press to play or pause a loaded

disc.

REPEAT

Press to repeat the

current chapter or

track or the entire

disc.

SKIP/SEARCH

Press to skip

between chapters

or tracks. Press

and hold to search

through the

current chapter or

track.

EJECT

Press to eject the

loaded disc from

the DISC DRIVE.

STOP

Press to stop a disc

during play.

GPX6

Page 7

Customer Support: 1-888-999-4215 GPX 7

10 +

CH LIST

DVD SETUP DVD MENU

FAV CH -FAV CH +

FAV LIST

TITLE

PROG USB/SD REPEAT A-B

SOURCE

DISPLAY

ADD/ERASE

VOLUME CHANNEL

SOUND

PICTURE

SUBTITLE

AUDIO

ANGLE

MUTE

POWER

AUTO

EJECT

POWER

Press to power the television o or on.

SLEEP

Press repeatedly to set the sleep timer.

After the set time has expired the television

will automatically power o.

ASPECT

Press to adjust the aspect ratio between

FULL, NORMAL, WATERGLASS, and CINEMA.

PICTURE

Press to adjust the picture between

STANDARD, MOVIE, USER, and DYNAMIC.

The user mode can be customized by

accessing Picture Settings in the menu.

SOUND

Press to adjust the sound between STANDARD, SOFT, USER, and DYNAMIC. The user mode can be customized by accessing

Sound Settings in the menu.

VOLUME

Press to adjust the volume.

Press to view the television setup menu.

AUDIO/SAP

Press to cycle through the available audio

settings in DVD mode. In TV mode, press to

switch to an alternate audio option when

supported.

DISPLAY

Press to view the on-screen display.

FAV LIST/PLAY/PAUSE

In TV mode, press to view your favorites list.

In DVD mode, press to play or pause the

loaded disc.

ADD/ERASE/STOP

In TV mode, press to add or erase the

current channel as a favorite. In DVD mode,

press to stop the current disc during play.

CH LIST/SKIP

In TV mode, press to view a list of

available channels. In DVD mode, press to

skip between chapters.

AUTO/SKIP

In PC mode, press to ne tune the position of the screen automatically. In DVD mode,

press to skip between chapters.

WIDE

In DVD mode, press to switch between

16:9, 4:3 PS, and 4:3 LB.

DVD SETUP

In DVD mode, press to access the DVD

setup menu.

PROGRAM

Press to program the loaded disc to play

chapters or tracks in a specied order.

USB/SD

In DVD mode, press to switch between USB

and SD card mode.

MUTE

Press to mute the volume.

NUMBER KEYPAD

ANGLE/PREV

Press to view alternate angles on supported DVDs. In TV mode, press to switch to the previous channel.

FREEZE

Press to freeze or unfreeze the current frame in DVD mode or TV mode.

EJECT/GUIDE

In DVD mode, press to eject the loaded disc. In TV mode, press to view the onscreen television guide.

CHANNEL

Press to adjust the television channel.

SUBTITLE/CC

Press to cycle through available subtitle settings in DVD mode. Press to view the closed captioning in TV mode.

EXIT

Press to exit the current menu.

ARROW KEYS

ENTER

SOURCE

Press to view the available television sources. Press the ARROW and ENTER buttons to adjust the current television source.

FAV CH +/-

Press to cycle through saved favorite channels in TV mode.

ZOOM

In DVD mode, press to zoom in or out on the current screen.

GOTO

In DVD mode, press to go to a specied title, chapter, and time.

Press to search through the current chapter or track.

TITLE

Press to access the title menu on a loaded DVD.

DVD MENU

Press to access the DVD menu on a loaded DVD.

A-B

While playing a DVD, press to set a specied section of DVD to repeat.

REPEAT

Press to repeat the current chapter or track or the entire disc.

Page 8

GPX8

AC power: requires an AC power cord (included).

Plug the included AC power cord into a standard AC power outlet to power the television.

Setup

Power

Requires 2, AAA size, batteries (included)

OPEN

Remote

Requires TV stand and 3 screws (included). Use a philips-head screwdriver to tighten the screws. Using an power drill could damage the TV stand.

TV Stand

Page 9

Customer Support: 1-888-999-4215 GPX 9

Requires a TV antenna (not included).

1. Connect a VHF, UHF, or HDTV antenna to the RF INPUT on the television.

2. Press the SOURCE button to switch to TV mode.

3. Press the MENU button to access the setup menu.

4. Press the ARROW () buttons to highlight the CHANNEL icon. Press the ENTER button.

5. Press the ARROW () buttons to highlight SIGNAL TYPE. Press the ARROW () buttons to select AIR.

6. Press the ARROW () buttons to highlight AUTO CHANNEL SEARCH. Press the ENTER button to begin scanning for available channels.

Television Setup

Connecting a TV Antenna

Connecting a Set-Top Box

Requires a cable connection.

1. Connect a cable to the RF INPUT on the television.

2. Press the SOURCE button to switch to TV mode.

3. Press the MENU button to access the setup menu.

4. Press the ARROW () buttons to highlight the CHANNEL icon. Press the ENTER button.

5. Press the ARROW () buttons to highlight SIGNAL TYPE. Press the ARROW () buttons to select AIR.

6. Press the ARROW () buttons to highlight AUTO CHANNEL SEARCH. Press the ENTER button to begin scanning for available channels.

Connecting Basic Cable

Requires a Set-Top Box (not included).

If your Set-Top Box has an HDMI Output:

• Connect the HDMI output on the Set-Top Box to the HDMI INPUT on the television using an HDMI cable (not included).

If your Set-Top Box has a Composite Video Output:

• Connect the video output on the Set-Top Box to the COMPOSITE VIDEO INPUT on the television using an A/V RCA cable (not included). Connect the audio output on the Set-Top Box to the RCA AUDIO INPUT on the television.

If your Set-Top Box has a Component Video Output:

• Connect the component video output on the Set-Top Box to the COMPONENT VIDEO INPUT on the television using a component RCA cable (not included). Connect the audio output on the Set-Top Box to the RCA AUDIO INPUT on the television.

After connecting your Set-Top Box:

• Press the SOURCE button to switch to YPBPR, S-VIDEO, AV, or HDMI to match the connection used.

Page 10

GPX10

1. Press the SOURCE button to switch to TV mode.

2. Press the CH LIST button, on the remote, to view a list of available channels.

Unless you are using a Set-Top Box, you must auto scan for channels before being able to view channels in list view.

1. Press the SOURCE button to switch to TV mode.

2. Press the CHANNEL buttons to select the desired TV channel.

3. Press the ADD/ERASE button to add or erase the current channel as a favorite.

1. Press the SOURCE button to switch to TV mode.

2. Press the FAV LIST button to view a list of your saved favorites.

1. Press the SOURCE button to switch to TV mode.

2. Press the MENU button.

3. Press the ARROW () buttons, highlight PARENTAL, and press the ENTER button.

4. The default passcode for the parental lock is: 0 0 0 0

5. Enter the passcode to access the PARENTAL CONTROL preferences.

6. From this menu, you can lock specic ratings from the United States rating system or the Canadian rating system by accessing the V-CHIP settings. You can also lock the buttons on the television or lock specic sources from access.

Television

Channel List View

Adding Favorites

Viewing Favorites

Parental Controls (V-Chip)

Auto Scanning for Channels

The Auto Channel Scan must be run before any channels can be viewed on the television.

1. Press the SOURCE button to switch to TV mode.

2. Press the MENU button to access the setup menu.

3. Press the ARROW () buttons to highlight the CHANNEL icon. Press the ENTER button.

4. Press the ARROW () buttons to highlight SIGNAL TYPE. Press the ARROW () buttons to select AIR.

5. Press the ARROW () buttons to highlight AUTO CHANNEL SEARCH. Press the ENTER button to begin scanning for available channels.

Page 11

Customer Support: 1-888-999-4215 GPX 11

Press the MENU button to access the TV menu. Press the EXIT button to exit the TV menu.

Picture

Picture Settings Screen Settings PC Settings Color Temperature Advanced Picture Settings

Sound

Sound Settings Surround Mode Analog Sound Digital Sound Other Settings

Channel

Channel List Favorite List Channel Setting Signal Type Auto Channel Search

Parental

Lock Parental Control V-Chip Change Password Front Panel Lock Source Lock

Setup

Closed Caption Menu Languag Clock

Others

Blue Back No Signal Power O No Operation Power O All Reset Audio Only

Television

Television Menu

1. Press the MENU button to access the setup menu.

2. Press the ARROW () buttons to highlight the SETUP icon. Press the ENTER button.

3. Press the ARROW () buttons to highlight CLOCK. Press the ENTER button.

4. Press the ARROW () buttons to highlight TIME ZONE. Press the ARROW () buttons to select your current time zone.

5. Press the ARROW () buttons to highlight AUTO CLOCK. Press the ARROW () buttons to turn auto clock o and on.

When the correct time zone is set, auto clock will automatically set your clock and date for you.

6. To set the time and date manually, turn auto clock o, highlight SETUP TIME, and use the ARROW and ENTER buttons to manually set the time and date.

Setting the Clock

Page 12

GPX12

1. Gently insert a DVD or CD into the slot-load disc drive, with the label side of the DVD or CD facing the back of the television.

Once a DVD or CD is loaded into the television, the TV will automatically switch to DVD mode.

DVD and CD

Loading a DVD or CD

1. Follow the instructions for Loading a DVD or CD.

2. After the DVD or CD is loaded, it will begin playing automatically.

If the DVD or CD does not begin playing automatically, press the PLAY/PAUSE button to begin playing the loaded disc.

Playing a DVD or CD

1. While a DVD or CD is playing, press the PROGRAM button on the remote.

2. Using the NUMBER KEYPAD enter in the title (T) and chapters (C), or tracks in the order you want them to play.

3. Highlight the on-screen PLAY button using the ARROW buttons and press the ENTER button.

4. The programmed titles and chapters, or tracks will now play in the designated order.

5. To cancel a program, press the PROGRAM button, highlight the on-screen CLEAR button using the ARROW buttons, and press the ENTER button.

Programming a DVD or CD

In DVD mode, press the DVD SETUP button to access the DVD setup menu. Press the DVD

SETUP button to exit the DVD setup menu.

System Setup

TV System Screen Saver TV Type Power Resume Default

Exit Setup

Language Setup

OSD Language Audio Language Subtitle Language Menu Language

Exit Setup

Audio Setup

Key

Exit Setup

Digital Setup

Dynamic Range Dual Mono Exit Setup

DVD Setup Menu

Page 13

Customer Support: 1-888-999-4215 GPX 13

USB Port and Memory Card Reader

1. Load an SD, MS, or MMC memory card into the MEMORY CARD READER as shown in the image to the right.

1. Load a USB thumb drive into the USB PORT as shown in the image to the right.

Connecting a Memory Card

Connecting a USB Thumb Drive

1. Follow the instructions for Connecting an SD or MMC card.

2. Press the SOURCE button to switch to DVD mode.

3. Press the USB/SD button on the remote to switch to the connected memory card.

4. Use the ARROW and ENTER buttons to select and play content from the connected memory card.

Using a Connected Memory Card

1. Follow the instructions for Connecting a USB thumb drive.

2. Press the SOURCE button to switch to DVD mode.

3. Press the USB/SD button on the remote to switch to the connected USB thumb drive.

4. Use the ARROW and ENTER buttons to select and play content from the connected USB thumb drive.

Using a Connected USB Thumb Drive

SDMMC

Page 14

GPX14

Connecting Other Devices (Set-Top Box, Gaming Device, DVD Player, VCR, or PC)

• You will need: a set-top box, s-video and RCA stereo cables or composite and RCA stereo cables or component and RCA stereo cables or an HDMI cable. (not included)

• Connect the set-top box’s audio and video outputs to the corresponding audio and video inputs on the television.

• Power the television on and press the SOURCE button to switch to the connected input. (AV (composite), YPbPr (component), S-VIDEO, or HDMI)

• You will need: a gaming device, s-video and RCA stereo cables or composite and RCA stereo cables or component and RCA stereo cables or an HDMI cable. (not included)

• Connect the gaming device’s audio and video outputs to the corresponding audio and video inputs on the television.

• Power the television on and press the SOURCE button to switch to the connected input. (AV (composite), YPbPr (component), S-VIDEO, or HDMI)

Connecting a Set-Top Box Connecting a Gaming Device

Page 15

Customer Support: 1-888-999-4215 GPX 15

• You will need: a DVD player or VCR, s-video and RCA stereo cables or composite and RCA stereo cables or component and RCA stereo cables or an HDMI cable.

• Connect the DVD player or VCR’s audio and video outputs to the corresponding audio and video inputs on the television.

• Power the television on and press the SOURCE button to switch to the connected input. (AV (composite), YPbPr (component), S-VIDEO, or HDMI)

• You will need: a PC with a VGA output, and a VGA cable. (not included)

• Connect the computer’s VGA output to the VGA/PC INPUT on the television.

• Power the television on and press the SOURCE button to switch to the PC Mode.

• Audio from the connected PC can be input to the television through the TV’s PC AUDIO INPUT by using a 3.5mm audio cable (not included).

Connecting a DVD Player or VCR Connecting a Computer

Page 16

GPX TD1920 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual