GoVideo VR5940 User Manual

DVD Recorder+VCR

VR5940

User's Guide

Safety Precautions

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: Do not install this equipment in a confined space such as a bookcase or similar unit.

NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

CAUTION:

This DVD Recorder+VCR employs a Laser System.

To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference. Should the DVD Recorder+VCR require maintenance, contact an authorized service center.

Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure.

To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the product and

receiver.

 Connect the product into an outlet on a circuit different

from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician

for help.

FCC COMPLIANCE: The responsible party for this product’s compliance is: GoVideo, 7835 East McClain Drive, Scottsdale, AZ 85260, USA.

SERIAL NUMBER: The serial number is found on the back of the DVD Recorder+VCR. This number is for this unit only. You should record requested information here and retain this guide as a permanent record of your purchase.

Model No. ___________________________________ Serial No. ___________________________________

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

INTRODUCTION

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions. - All these safety and oper-

ating instructions should be read before the product is operated.

2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.

3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.

4. Follow all instructions. - All operating and use instructions should be followed.

5. Do not use this product near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; or near a swimming pool; and other areas located near water.

6. Clean only with dry cloth. - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatuses (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the product.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with apparatus. When a cart is used, use caution when moving the cart/product combination to avoid injury from tip-over.

13. Unplug this product during lightning storms or when unused for long periods of time.

14.

Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as: Power-supply cord or plug is damaged; liquid has been spilled or objects have fallen into the product; the product has been exposed to rain or moisture, does not operate normally, or has been dropped.

CAUTION:

PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL AND THOSE MARKED ON THE PRODUCT. RETAIN THIS MANUAL FOR FUTURE REFERENCE.

This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing. This product does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

Table of Contents

INTRODUCTION

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

Recordable Discs . . . . . . . . . . . . . . . . . . . . . . . 6

Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . 6

Disc-related Terms . . . . . . . . . . . . . . . . . . . . . . 6

About Recordable Discs . . . . . . . . . . . . . . . . . . 7

What are “Recording Modes”? . . . . . . . . . . . . . 7

• Is Editing a DVD like Editing a Videotape? . 7

• “Original” Content vs “Playlist” Content . . . . 7

About DVD Recording . . . . . . . . . . . . . . . . . . 7-8

• Disc Types and Recording Formats . . . . . . 7

• What is ‘DoMiNoFX™’? . . . . . . . . . . . . . . . 7

• Notes for Recording . . . . . . . . . . . . . . . . . . 8

• Recording TV Audio Channels . . . . . . . . . . 8

• Restrictions on Video Recording. . . . . . . . . 8

• What is ‘CPRM’? . . . . . . . . . . . . . . . . . . . . 8

• Copyright Notice . . . . . . . . . . . . . . . . . . . . 8

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

• Handling the Unit . . . . . . . . . . . . . . . . . . . . 9

• Cleaning the Unit . . . . . . . . . . . . . . . . . . . . 9

• Moisture Condensation. . . . . . . . . . . . . . . . 9

• Remote Control Operating Range. . . . . . . . 9

• Remote Control Battery Installation . . . . . . 9

Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . 9

• Handling Discs . . . . . . . . . . . . . . . . . . . . . . 9

• Storing Discs . . . . . . . . . . . . . . . . . . . . . . . 9

• Cleaning Discs . . . . . . . . . . . . . . . . . . . . . . 9

About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . 9

• About the Symbol . . . . . . . . . . . . . . . . . 9

• Symbols Used in this Manual . . . . . . . . . . 9

Front Panel Overview . . . . . . . . . . . . . . . . . . . 10

Front Panel Display Overview . . . . . . . . . . . . . 11

Remote Control Overview . . . . . . . . . . . . . . . . 12

Rear Panel Overview . . . . . . . . . . . . . . . . . . . . 13

CONNECTIONS & SETUP

Connections . . . . . . . . . . . . . . . . . . . . . . . . 14-17

Connecting Antenna/Cable . . . . . . . . . . . . . . . 14

Connecting a TV. . . . . . . . . . . . . . . . . . . . . . . 15

Connecting an Amplifier/Receiver . . . . . . . . . . 16

Connecting Optional Equipment . . . . . . . . . . . 17

Connecting a Digital Camcorder . . . . . . . . . . . 17

Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . 18-29

Setup Menu Overview. . . . . . . . . . . . . . . . . . . 18

Setup Menu Navigation. . . . . . . . . . . . . . . . . . 18

GENERAL Settings . . . . . . . . . . . . . . . . . . 18-20

•Tuning Band. . . . . . . . . . . . . . . . . . . . . . . 18

• Auto Channel Set. . . . . . . . . . . . . . . . . . . 18

• Channel Add/Delete . . . . . . . . . . . . . . . . . 19

• Clock (Auto) . . . . . . . . . . . . . . . . . . . . . . . 19

• Clock (Manual). . . . . . . . . . . . . . . . . . . . . 19

• TV Aspect Ratio . . . . . . . . . . . . . . . . . . . . 20

• Progressive Scan . . . . . . . . . . . . . . . . . . . 20

• Factory Setting. . . . . . . . . . . . . . . . . . . . . 20

LANGUAGE Settings . . . . . . . . . . . . . . . . . . . 20

• Display Menu Language. . . . . . . . . . . . . . 20

• Disc Menu/Audio/Subtitle Language . . . . . 20

AUDIO Settings . . . . . . . . . . . . . . . . . . . . . . . 21

• Dolby Digital. . . . . . . . . . . . . . . . . . . . . . . 21

• DTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

• MPEG . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

• Sampling Frequency . . . . . . . . . . . . . . . . 21

• DRC (Dynamic Range Control). . . . . . . . . 21

• Surround . . . . . . . . . . . . . . . . . . . . . . . . . 21

LOCK Settings. . . . . . . . . . . . . . . . . . . . . . 22-23

• Movie Rating . . . . . . . . . . . . . . . . . . . . . . 22

• Password . . . . . . . . . . . . . . . . . . . . . . . . . 22

• Country Code. . . . . . . . . . . . . . . . . . . . . . 23

RECORD Settings . . . . . . . . . . . . . . . . . . . 23-24

• Disc Record Mode . . . . . . . . . . . . . . . . . . 23

• VCR Record Mode . . . . . . . . . . . . . . . . . . 23

• DV Record Audio . . . . . . . . . . . . . . . . . . . 24

• Auto Chapter . . . . . . . . . . . . . . . . . . . . . . 24

DISC Settings . . . . . . . . . . . . . . . . . . . . . . 24-26

• Disc Initialize . . . . . . . . . . . . . . . . . . . . . . 24

• Disc Finalize . . . . . . . . . . . . . . . . . . . . . . 25

• Disc Protect . . . . . . . . . . . . . . . . . . . . . . . 25

• PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

• AutoPlay . . . . . . . . . . . . . . . . . . . . . . . . . 25

•YourDVD . . . . . . . . . . . . . . . . . . . . . . . . . 26

• Disc Label . . . . . . . . . . . . . . . . . . . . . . . . 26

On-Screen Display Overview . . . . . . . . . . . . . 27

• Displaying Disc Information . . . . . . . . . . . . . 27

• Displaying TV Information . . . . . . . . . . . . . . 27

• Changing TV Channels . . . . . . . . . . . . . . . . 27

• Changing TV Audio Channels . . . . . . . . . . . 27

OSD Menu Options by Media Type . . . . . . 28-29

• DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

•VR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

•Video & +R/RW . . . . . . . . . . . . . . . . . . . . . . 29

• VHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

PLAYBACK

DVD Playback . . . . . . . . . . . . . . . . . . . . . . . 30-33

Playing a DVD . . . . . . . . . . . . . . . . . . . . . . . . 30

• Selecting Titles . . . . . . . . . . . . . . . . . . . . 30

• Selecting Chapters . . . . . . . . . . . . . . . . . . 30

• Slow Motion . . . . . . . . . . . . . . . . . . . . . . . 30

•

Still Picture and Frame-by-Frame Playback

. 31

• Search . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

• Random . . . . . . . . . . . . . . . . . . . . . . . . . . 31

• Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . 31

• Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . 31

•Time Search. . . . . . . . . . . . . . . . . . . . . . . 32

• Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

• Marker Search . . . . . . . . . . . . . . . . . . . . 32

• Disc Menus . . . . . . . . . . . . . . . . . . . . . . . 32

•Title Menus . . . . . . . . . . . . . . . . . . . . . . . 32

• Camera Angle . . . . . . . . . . . . . . . . . . . . . 33

• Changing the Audio Language . . . . . . . . . 33

• 3D Surround . . . . . . . . . . . . . . . . . . . . . . 33

• Subtitles. . . . . . . . . . . . . . . . . . . . . . . . . . 33

• Remember Disc Settings . . . . . . . . . . . . . 33

Table of Contents

INTRODUCTION

Audio CD and MP3/WMA Operation. . . . . . . . . 34-35

Playing an Audio CD or MP3/WMA Disc . . . . . 34

Music Menu Options . . . . . . . . . . . . . . . . . . . . 34

• Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

• Skip Tracks . . . . . . . . . . . . . . . . . . . . . . . 35

• Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . 35

• Random . . . . . . . . . . . . . . . . . . . . . . . . . . 35

• Search . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

• Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . 35

• Notes on MP3/WMA Recordings. . . . . . . . 35

Program Playback with Audio CD and MP3/WMA

. . . . . . . . . . . . . . . . . . . . . . . . 36-37

JPEG Disc Operation

. . . . . . . . . . . . . . . . . . . 38-39

Viewing a JPEG file . . . . . . . . . . . . . . . . . . . . 38

Photo Menu Options . . . . . . . . . . . . . . . . . . . . 38

• Still Picture. . . . . . . . . . . . . . . . . . . . . . . . 39

• Skip Images . . . . . . . . . . . . . . . . . . . . . . . 39

• Rotate Images . . . . . . . . . . . . . . . . . . . . . 39

•View Slide Shows. . . . . . . . . . . . . . . . . . . 39

• Notes on JPEG Recordings . . . . . . . . . . . 39

VCR Playback. . . . . . . . . . . . . . . . . . . . . . . . . . 40

Before You Begin . . . . . . . . . . . . . . . . . . . . . . 40

Playing a VHS Tape . . . . . . . . . . . . . . . . . . . . 40

Tracking Control . . . . . . . . . . . . . . . . . . . . . . . 40

Special Playback Features . . . . . . . . . . . . . . . 40

• Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

• Still Picture and Frame-by-Frame Playback . 40

• Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . 40

• Counter Memory Function . . . . . . . . . . . . . . 40

RECORDING

Basic Recording . . . . . . . . . . . . . . . . . . . . . 41-42

Recording from TV . . . . . . . . . . . . . . . . . . . . . 41

One Touch Record (OTR) . . . . . . . . . . . . . . . . 41

One Touch Copy - DVD to VHS . . . . . . . . . . . 42

One Touch Copy - VHS to DVD . . . . . . . . . . . 42

Timer Recording . . . . . . . . . . . . . . . . . . . . . . . 43

Checking Timer Recording Details . . . . . . . . . 43

Canceling a Timer Recording . . . . . . . . . . . . . 43

Stopping a Timer Recording in Progress . . . . . 43

Timer Recording Troubleshooting . . . . . . . . . . 43

Recording from an External Input . . . . . . . 44-45

Recording from External Components. . . . . . . 44

Recording from a Digital Camcorder . . . . . . . . 44

Playing Recordings on other DVD Players

. . . . . 44

• Finalizing a Disc. . . . . . . . . . . . . . . . . . . . 44

What is DV? . . . . . . . . . . . . . . . . . . . . . . . . . . 45

•DV-Related Messages . . . . . . . . . . . . . . . 45

•Troubleshooting . . . . . . . . . . . . . . . . . . . . 45

EDITING

Title List and Chapter List Menu . . . . . . . . 46-57

Using the Title List-Original menu (VR) . . . . . 46

Using the Chapter List-Original menu (VR) . . . 46

Using the Title List-Playlist Menu (VR) . . . . . . 47

Using the Chapter List-Playlist Menu (VR). . . . 47

Using the Title List menu (Video). . . . . . . . . . . 48

Deleting a Title (Video) . . . . . . . . . . . . . . . . . . 48

Using the Title List menu (+RW) . . . . . . . . . . . 49

Using the Chapter List menu (+RW) . . . . . . . . 49

Using the Title List menu (+R). . . . . . . . . . . . . 50

Using the Chapter List menu (+R). . . . . . . . . . 50

Title and Chapter Editing. . . . . . . . . . . . . . . . . 51

About Original vs. Playlist Content (VR) . . . . . 51

About Titles, Chapters and Parts (VR). . . . . . . 51

Adding Chapter Markers (VR) . . . . . . . . . . . . 51

Changing Title Thumbnails (VR/+R/+RW) . . . . 51

Making a New Playlist (VR) . . . . . . . . . . . . . . 52

Adding Titles/Chapters to a Playlist (VR). . . . . 52

Deleting Titles/Chapters (VR/+R/+RW) . . . . . . 53

Deleting Part of a Title (VR) . . . . . . . . . . . . . . 53

Renaming a Title (VR/Video/+R/+RW) . . . . . . 54

Combining Two Chapters (VR/+R/+RW) . . . . . 54

Moving a Playlist Chapter (VR) . . . . . . . . . . . 55

Protecting a Title (VR/+R/+RW). . . . . . . . . . . . 55

Hiding a Title/Chapter (+R/+RW) . . . . . . . . . . 56

Dividing a Title (+RW). . . . . . . . . . . . . . . . . . . 56

Overwriting a Disc (Video/VR/+RW) . . . . . . . . 57

Overwriting a Title (+RW) . . . . . . . . . . . . . . . . 57

Previewing Title Menus (+R/+RW) . . . . . . . . . 57

About Playing Recordings

on Other DVD Players . . . . . . . . . . . . . . . . . . 57

REFERENCE

Programming the MultiBrand Remote

to Control Your TV . . . . . . . . . . . . . . . . . . . . . . 58

Language Code List. . . . . . . . . . . . . . . . . . . . . 59

Country Code List . . . . . . . . . . . . . . . . . . . . . . 60

Troubleshooting . . . . . . . . . . . . . . . . . . . . . 61-62

Technical Specifications . . . . . . . . . . . . . . . 63-64

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . 65

Symbols Used in this Manual

Indicates hazards likely to cause harm to the unit itself or other material damage.

Indicates special operating features of the DVD Recorder+VCR.

Indicates helpful tips and hints.

Overview

Recordable Discs

This DVD Recorder+VCR is a dual-format unit, which means you can record on DVD-R, DVD-RW, DVD+R, or DVD+RW recordable discs. Look for discs with the following logos:

otes

– The DVD Recorder+VCR cannot record on CD-R or

CD-RW discs.

– DVD-R/RW and CD-R/RW discs recorded using a

personal computer or a DVD or CD recorder may not play if the disc is damaged or dirty, or if there is dirt or condensation on the DVD Recorder+VCR’s lens.

– If you record a disc using a personal computer, even

if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.)

Playable Discs

DVD (8 cm/12 cm disc)

Video CD (VCD) (8 cm / 12 cm disc)

Audio CD (8 cm/12 cm disc)

In addition, the DVD Recorder+VCR can play DVDR/DVD-RW discs; DVD+R/DVD+RW discs; SVCD discs; CD-R/CD-RW discs that contain audio, MP3/WMA, or JPEG files; and Kodak Picture CDs.

otes

– Depending on the conditions of the recording equip-

ment or the recordable disc (including CD-R/RW, DVD-R/-RW, and DVD+R/+RW), some discs cannot be played on the DVD Recorder+VCR.

– Do not attach any seal or label to either side (the

labeled side or the recorded side) of a disc.

–

Do not use irregularly shaped CDs (e.g., heart-shaped or octagonal). Doing so may result in malfunctions.

Regional code of the DVD Recorder+VCR and DVDs

This DVD Recorder+VCR is designed and manufactured for playback of Region 1 encoded DVD software. The region code on the labels of some DVD discs indicates which type of DVD Recorder+VCR can play those discs. The DVD Recorder+VCR can play only DVD discs labeled 1 or ALL. If you try to play any other discs, the message “Incorrect region code. Can’t playback” will appear on the

TV screen. Some DVD discs may not have a region code label even though their playback is prohibited by area limits.

otes on DVDs and Video CDs

Some DVD and Video CD playback operations may be intentionally set by the software manufacturer. As this DVD Recorder+VCR plays DVDs and Video CDs according to disc content designed by the software manufacturer, some DVD and Video CDs playback features may not be available or other functions may be added. Refer also to the instructions supplied with your DVDs and Video CDs. Some DVDs made for business purposes may not be played on this unit.

Disc Related Terms

Title (DVD only)

The main film content or accompanying feature content or music album. Each title is assigned a title reference number enabling you to locate it easily.

Chapter (DVD only)

Sections of a picture or a musical piece that are smaller than titles. A title is composed of one or several chapters. Each chapter is assigned a number to enable you to easily locate the chapter you want. Depending on the disc, chapters may not be labeled.

Track (Video CD and Audio CD only)

Sections of a picture or a musical piece on a video CD or an audio CD. Each track is assigned a number, enabling you to easily locate the track you want.

Scene

On a video CD with PBC (Playback Control), movies and pictures are divided into “scenes”. Each scene is displayed on a menu and assigned a number, enabling you to quickly locate the scene you want. A scene may be composed of one or several tracks.

Types of Video CDs

There are two types of video CDs:

Video CDs equipped with PBC (Version 2.0)

PBC (Playback control) allows you to interact with the contents of a Video CD using menus, search functions, and other special operations. High resolution pictures can be displayed if they are included on the disc.

Video CDs not equipped with PBC (Version 1.1)

Video CDs without PBC are similar to audio CDs, except they allow playback of video as well as sound.

INTRODUCTION

Overview (Continued)

About Recordable Discs

How are +/-R and +/-RW discs different?

+/-R is a record-once medium, while +/-RW is a rerecordable/erasable medium. You can re-record/ erase an RW disc approximately 1,000 times.

Can I play my discs in a regular DVD player?

Discs recorded in “Video mode” are playable in most standard DVD players, but they must be finalized first. This process fixes the contents of your discs so they are readable on other DVD players as standard DVDVideo discs. DVD-RW discs recorded in “VR mode” (Video Recording mode) are only readable on players with the “RW Compatible” logo.

This logo indicates that a product is capable of playing DVD-RW discs recorded in “VR mode”.

What are “Recording Modes”?

Two recording modes are available on your DVD Recorder+VCR: “Video mode” and “VR mode”:

About “VR mode”

• Compatible with DVD-RW discs only

• Allows extensive editing of DVD-RW recordings

• Discs are not playable on regular DVD players

•4 different picture quality/recording time settings are available: XP (1 hr/disc), SP (2 hrs/disc), LP (4 hrs/disc), and EP (6 hrs/disc)

About “Video mode”

• Compatible with all discs (DVD-R/RW, DVD+R/RW)

• Provides limited editing features

• Playable on most regular DVD players (after finalizing)

•4 different picture quality/recording time settings are available: XP (1 hr/disc), SP (2 hrs/disc), LP (4 hrs/disc), and EP (6 hrs/disc)

ote

Discs formatted in “Video mode” are recorded in the DVD-Video format, which was approved by the DVD Forum in 2000. As a result, you may experience problems playing your discs in some older players. Symptoms include video artifacts, audio and/or video dropouts and playback suddenly stopping. Our company cannot take responsibility for problems playing discs recorded on this DVD Recorder+VCR in other players.

Is Editing a DVD like Editing a Videotape?

No. When you edit a videotape you need one video deck to play the original tape and another to record the edits. With DVD, you edit by making a “Playlist” of what to play and when to play it. During playback, the DVD Recorder+VCR plays the disc according to your Playlist.

“Original” Content vs “Playlist” Content

Throughout this manual, you will often see the words “Original” and “Playlist” to distinguish between the actual content on your DVD-RW and the edited version.

• Original: Refers to what is actually recorded on the disc.

• Playlist: Refers to the edited version of the disc — i.e., how the Original content is to be played.

About DVD Recording

otes

• The DVD Recorder+VCR cannot make recordings on CD-R or CD-RW discs.

• Our company takes no responsibility for recording failure due to power outages, defective discs, or damage to the DVD Recorder+VCR.

• Fingerprints and small scratches on a disc can affect playback and/or recording performance. Please take proper care of your discs.

Disc Types and Recording Formats

The DVD Recorder+VCR can play the following DVD discs:

1. Pre-recorded DVD-Video discs

2. DVD-R/DVD-RW discs

3. DVD+R/DVD+RW discs

DVD-R, DVD+R, and DVD+RW discs are always formatted in “Video mode”—the same format as prerecorded DVD-Video discs. This means that once the disc is finalized, you can play it in most standard DVD players.

DVD-RW discs can be formatted in either “Video mode” or “VR mode” (Video Recording mode). Keep in mind that changing between these modes requires you to reinitialize the disc, which will erase its contents.

What is ‘DoMiNoFX™’?

DoMiNoFX™ is a patented video processing technology that digitally enhances and refines the picture quality during recording. This results in visibly superior recordings, and a dramatic improvement when recording from noisy source material, such as VHS tapes or weak TV signals.

Overview (Continued)

Notes for Recording

• The recording times shown are not exact because the DVD Recorder+VCR uses variable bit-rate video compression. This means that the exact recording time will depend on the material being recorded.

• When recording a TV broadcast, if the reception is poor or the picture contains interference, the recording times may be shorter.

• If you record still pictures or audio only, the recording time may be longer.

• The displayed times for recording and time remaining may not always add up to exactly the length of the disc.

• The recording time available may decrease if you heavily edit a disc.

• If using a DVD-RW disc, make sure you change the recording format (Video mode or VR mode) before you record anything on the disc. See page 24 (“Disc Initialize”) for how to do this.

• When using a DVD-R or DVD+R disc, you can keep recording until the disc is full, or until you finalize the disc. Before you start a recording session, check the amount of recording time left on the disc.

• When using a DVD+RW disc or a DVD-RW disc in Video mode, recording time available will only increase if you erase the last title recorded on the disc.

• The Erase Title option in the Original (Title) menu only hides the title, it does not actually erase the title from the disc and increase the recording time available (except for the last recorded title on a DVD+RW disc or a DVD-RW disc in Video mode).

Recording TV Audio Channels

The DVD Recorder+VCR can record one or two channel audio. For TV broadcasts, this usually means mono or stereo, but some programs are broadcast with a main and a SAP (Secondary Audio Program) audio channel. If you’re recording in Video mode (or in VR mode), you can record either the main audio or the SAP audio.

Restrictions on Video Recording

•You cannot record copy-protected video using this DVD Recorder+VCR. Copy-protected video includes DVD-Video discs and some satellite broadcasts. If copy-protected material is encountered during a recording, recording will pause or stop automatically and an error message will be displayed on-screen.

•Video that is ‘copy-once only’ can only be recorded using a DVD-RW disc in VR mode with CPRM (see below).

What is ‘CPRM’?

CPRM is a copy protection system (with scramble system) only allowing the recording of ‘copy once’ broadcast programs. CPRM stands for Content Protection for Recordable Media. The DVD Recorder+VCR is CPRM compatible, which means that you can record copy-once broadcast programs, but you cannot then make a copy of those recordings. CPRM recordings can only be made on DVD-RW discs formatted in VR mode, and CPRM recordings can only be played on players that are specifically compatible with CPRM.

• Audio and video recordings you make using the DVD Recorder+VCR are for your personal use only. You may not sell, lend or rent them to other people.

• This product incorporates copyright protection technology that is protected by method claims of certain U.S.patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision corporation. Reverse engineering or disassembly is prohibited.

Disc Type Disc Format Recording Mode Editing Features

DVD-Video Video Format Playback only N/A

DVD-RW Video Recording VR mode Create & Modify Playlists; Delete Titles/Chapters;

Format (default) Delete Parts of Titles; Combine Chapters;

Rename Titles; Protect Titles.

Video format Video mode Rename Titles; Delete Titles.

DVD-R Video format Video mode Rename Titles; Delete Titles.

DVD+RW +RW Video format DVD+RW mode Rename Titles; Delete Titles; Hide/Show Chapters;

Divide Titles; Combine Chapters; Protect Titles

DVD+R +R Video format DVD+R mode Rename Titles; Delete Titles; Hide/Show Chapters;

Combine Chapters; Protect Titles

Precautions

Handling the Unit

When shipping the unit

The original shipping carton and packing materials come in handy. For maximum protection, re-pack the unit as it was originally packaged at the factory.

When setting up the unit

The picture and sound of a nearby TV, VCR, or radio may be distorted during playback. In this case, position the unit away from the TV, VCR, or radio, or turn off the unit after removing the disc.

To keep the surface clean

Do not use volatile liquids, such as insecticide spray, near the unit. Do not leave rubber or plastic products in contact with the unit for a long period of time. They will leave marks on the surface.

Cleaning the Unit

To clean the cabinet

Use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit.

To obtain a clear picture

The DVD Recorder+VCR is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality will be poor. Regular inspection and maintenance are recommended after every 1,000 hours of use. (This depends on the operating environment.) For details, please contact your nearest dealer.

Moisture Condensation

Never operate the DVD Recorder+VCR immediately after moving it from a cold location to a warm location. Leave it for two or three hours without operating it. If you use the unit in such a situation, it may damage discs/tapes and internal parts.

Remote Control Operation Range

Point the remote control at the remote sensor and press the buttons.



Distance: About 23 ft (7 m) from the front of the remote sensor.



Angle: About 30° in each direction of the front of the remote sensor.

Remote Control Battery Installation

Detach the battery cover on the rear of the remote control, and insert two size AAA batteries with and aligned correctly.

Caution

Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.)

Notes on Discs

Handling Discs

Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints will not get on the surface. Do not stick paper or tape on the disc.

Storing Discs

After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat, or leave it in a parked car exposed to direct sunlight, as there may be a considerable temperature increase inside the car.

Cleaning Discs

Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center outward. Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.

About Symbols

About the Symbol

“ ” may appear on the TV screen during operation. This icon means the function explained in this owner’s manual is not available on that specific disc or at that time.

Symbols Used in this Manual

Many functions provided on this recorder are dependent on the Recording mode. One or more of the symbols ( , , ) appear by each function explained in this manual so that you can see at a glance whether it’s applicable to the disc loaded.

DVD-R/RW with Video recording mode

DVD-RW with VR recording mode DVD+R/RW disc DVD-Video disc

Audio CDs MP3 CDs WMA CDs JPEG CDs VHS Tape

A finalized DVD disc is a DVD-Video disc.

VHS

JPEG

WMA

MP3

DVD

+R/RW

Video

+R/RW

Video

INTRODUCTION

Overview (Continued)

REC (z)

Starts recording. Press

repeatedly to set the

recording time.

CH (V / v)

Scans up or down through memorized channels.

PLAY (N)

Starts playback of a disc or tape.

DVD EJECT (Z)

Opens or closes the disc tray.

AV 2 IN (VIDEO, L-AUDIO-R)

Connects to the audio/video output of an external source (VCR, Camcorder, etc.).

S-VIDEO IN

Connects to the S-Video output of an external source (VCR, Camcorder, etc.).

PAUSE (X)

Pauses playback or recording

temporarily.

Press repeatedly for frame-by-

frame playback.

Disc Tray (DVD deck)

Insert a disc here.

POWER button and indicator

Switches the DVD Recorder+VCR ON and OFF. Lights green when the DVD Recorder+VCR is turned on.

STOP (x)

Stops playback.

COPY

Copies from DVD to VCR (or from VCR to DVD).

Cassette Compartment (VCR deck)

Insert a video cassette here.

VCR EJECT

Ejects the tape in the VCR deck.

SELECT DVD/VCR

Toggles control between the DVD

deck and the VCR deck.

FF (>)

DVD: Skips to the next chapter/track. Press and hold for

fast forward search.

VCR: Advances the tape during Stop mode. Press during

Play mode for fast forward picture search.

REW (.)

DVD: Skips to the beginning of the current

chapter/track or to the previous chapter/track.Press

and hold for fast reverse search.

VCR: Rewinds the tape during Stop mode. Press

during Play mode for fast reverse picture search.

Front Panel Display

Shows the current status of

the DVD Recorder+VCR.

Front Panel Overview

DV IN

Connects to the DV output of a digital camcorder.

DVD

PRG TTL VR TRKCHP DUB

Hi-Fi ST

SAP

SVCD

REC

INTRODUCTION

Front Panel Display Overview

ST Indicates that a stereo broadcast

is being received.

Disc Type indicators

Indicates the type of disc loaded.

Hi-Fi Indicates when the DVD Recorder+VCR is playing

or recording a tape in Hi-Fi.

DUB Indicates that a DVD to VCR (or VCR to

DVD) copy is in progress.

Front Panel Display Message

Indicates clock, total playing time, elapsed

time, remaining time, title number,

chapter/track number, channel, etc.

REPEAT Indicates current Repeat mode.

REC Indicates that a recording is in progress.

Indicates that a timer recording is in

progress or is programmed.

SAP Indicates when a Second Audio Program

(SAP) broadcast is being received.

PRG Indicates that program playback is active.

TTL Indicates current title number.

Indicates a disc is inserted in the DVD deck.

Indicates a VHS tape is inserted in the VCR deck.

Indicates a DVD-RW disc (VR mode only) is inserted in the DVD deck.

CHP/TRK Indicates the current chapter or track number.

Indicates when the DVD Recorder+VCR is locked.

Remote Control Overview

POWER

Turns DVD Recorder+VCR on and off.

TV/VCR

Switches between the DVD

Recorder+VCR tuner and your TV tuner.

DVD

Selects DVD mode.

VCR

Selects VCR mode.

INPUT

Switches the DVD Recorder+VCR input

to Tuner, AV1, AV2, or DV IN.

0-9 buttons

Selects numbered options in menus.

Selects TV channels.

TV Control Buttons

TV POWER: Turns TV on and off.

TV INPUT: Selects TV input source.

v/V: Selects TV channels.

VOL +/–: Adjusts TV volume.

MUTE: Turns TV sound on or off.

REC MODE

Selects Recording mode:

- DVD : XP (1 hr), SP (2 hrs), LP (4 hrs) or EP (6 hrs).

- VCR : SP or SLP.

TIMER RECORD

Displays Timer Recording menu.

REC (z)

Starts recording. Press repeatedly to set

the recording time.

REW/FF (m / M)

DVD: Searches backward/forward.

VCR: Rewinds/advances during Stop

mode. Press during Play mode for fast

reverse/forward picture search.

PREV/NEXT (. / >)

Skips to next chapter/track. Returns to

beginning of current chapter/track or

skips to previous chapter/track.

AUDIO

Selects an audio language (DVD).

SUBTITLE

Selects a subtitle language.

ANGLE

Selects a DVD camera angle,

if available.

ZOOM

Enlarges DVD video image.

EJECT

- Opens and closes disc tray.

- Ejects tape in VCR deck.

COPY

Copies DVD to VCR (or VCR to DVD).

CLEAR

Removes bookmarks from Marker Search menu.

TITLE

Displays disc’s Title menu, if available.

DISC MENU/LIST

Accesses menus on DVD discs. Switches between Original and Playlist editing in VR mode.

SETUP

Displays or exits Setup menu.

DISPLAY

Displays or exits On-Screen Display.

RETURN (O)

Exits or returns to previous screen in Setup menu.

bBvV(left/right/up/down)

Selects menu options.

CH/TRACK(

v/V): Selects channels.

Manually adjusts tracking.

ENTER

Confirms menu selections.

PAUSE/STEP (X)

Pauses playback or recording temporarily. Press repeatedly for frame-by-frame playback.

PLAY (N)

Starts playback.

STOP (x)

Stops playback or recording.

ADD CHAP

Inserts chapter marker when playing/ recording DVD+R/RW discs or DVD-RW discs in VR mode.

THUMBNAIL

Selects a thumbnail picture for the current title for use in the Title List or Chapter List menu.

REPEAT

Repeats chapter, track, title, or all.

A-B

Repeats sequence between two points (A and B).

MARKER

Marks any point during playback.

Displays Marker Search menu.

CHILD LOCK

Locks/unlocks front panel buttons.

RANDOM

Plays tracks in random order.

CHILD LOCK

The Lock feature disables the front panel buttons to prevent children from tampering with the DVD Recorder+VCR. Simply press CHILD LOCK on the remote control to toggle this feature on and off.

VCR

EJECT

INPUT

COPY

CLEAR

POWER

TV/VCR

DVD

7890

TV POWER MUTE

TV INPUT

DISC MENU

LIST

DISPLAY

REC MODE TIMER RECORD

PAUSE/STEP

VOL

CH+

TRACK+

ENTER

TRACK-

CH–

REC

STOP

PLAY

REW FF

PREV NEXT

AUDIO SUBTITLE ANGLE ZOOM

ADD CHAP THUMBNAIL REPEAT A-B

MARKER SEARCH RANDOM

CHILD LOCK

TITLE

SETUP

RETURN

INTRODUCTION

Rear Panel Overview

Caution Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the DVD Recorder+VCR.

RF IN (FROM ANT.)

Connect to your antenna or cable TV outlet.

COAXIAL (Digital Audio Out)

Connect to an amplifier with a coaxial digital audio input.

AUDIO OUT (L, R)

Connect to a TV or other equipment with audio inputs.

AV OUT

(VIDEO, L-AUDIO-R)

Connect to a TV with video and audio inputs.

COMPONENT/PROGRESSIVE VIDEO OUT (Y Pb Pr)

Connect to a TV with Component (Y Pb Pr) inputs.

AV 1 IN (VIDEO, L-AUDIO-R)

Connect to the audio/video output of an external source (VCR, Camcorder, etc.).

AC Power Cord

Plug into a power outlet.

S-VIDEO OUT

Connect to a TV with an S-Video Input.

OPTICAL (Digital Audio Out)

Connect to an amplifier with an optical digital audio input.

RF OUT (TO TV)

Connect to a TV with an RF coaxial input.

Connections

ips



There are a variety of ways to connect the DVD Recorder+VCR to your TV and other equipment. Use only one of the connections described below. Whichever TV connection you use will work with all input sources.



Please refer to the manuals for your TV, VCR, stereo system or other devices as necessary to make the best connections.



For better sound reproduction, connect the DVD Recorder+VCR’s AUDIO OUT jacks to the audio in jacks of your amplifier, receiver, stereo or audio/video equipment. See “Connecting an Amplifier/Receiver” on page 16.

Caution

– Make sure the DVD Recorder+VCR is connected

directly to the TV, and the TV is set to the correct video input.

–

Do not connect the DVD Recorder+VCR’s AUDIO OUT jack to the phono in jack (record deck) of your audio system.

– Do not connect the DVD Recorder+VCR via your

VCR. The DVD image could be distorted by the copy protection system.

Connecting Antenna/Cable

Disconnect the antenna/cable from the rear of your TV.

Identify the type of cable from your antenna. If it is a round cable as illustrated, it is a 75 ohm coaxial antenna cable. This cable will connect directly to the jack marked RF IN (FROM ANT.) on the DVD Recorder+VCR.

If your antenna lead wire is a flat type antenna cable, connect it to a 300-ohm to 75-ohm antenna adapter (not supplied) and slip the adapter onto the RF IN (FROM ANT.) jack. The Adapter does not screw on to the unit, it just slips over the jack.

Cable Service Without Cable Box

If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your TV and attach it to the

RF IN (FROM ANT.) jack on the DVD Recorder+VCR.

Use the supplied coaxial cable to connect between the DVD Recorder+VCR’s OUT (TO TV) jack and the 75 ohm antenna input jack on your TV. With this connection, you can receive all midband, superband, and hyperband channels (all cable channels).

Cable Service With Cable Box

If a cable box is required in your cable system, follow the instructions shown below. This hookup permits both TV and DVD Recorder+VCR operation.

To view or record a CATV channel: 1

Tune the TV to the correct video input channel.

2 Set the DVD Recorder+VCR to the output channel of the

cable box using the CH (v / V) or the 0-9 keys on your DVD Recorder+VCR (e.g., CH3).

3 Select the channel you wish to view on the cable box.

ote

If you are using a cable box to tune channels, it is not necessary to run Auto Channel Set as indicated on page 18.

Antenna Antenna

Flat Wire

(300 ohm)

300/75 ohm

Adaptor

(Not supplied)

Cable TV

Wall Jack

OR OR

Rear of DVD Recorder+VCR

Cable TV

Wall Jack

Back Panel of

Typical Cable Box

Rear of DVD Recorder+VCR

CONNECTIONS & SETUP

Connections (Continued)

Connecting a TV

Choose one of the following TV connections, depending on the capabilities of your equipment.

ote

All video signals are available from all video outputs. That means that whichever TV connection you

use, it will work with all input sources, including VHS out of the Component/Progressive Video Output.

RF Coaxial Connection

Connect the RF OUT (TO TV) jack on the DVD Recorder+VCR to the antenna in jack on your TV using the supplied 75-ohm coaxial cable (R). If you use this connection, tune your TV to the DVD Recorder+VCR’s RF output channel (CH 3 or 4).

How to set the DVD Recorder+VCR’s RF output channel

Turn off the DVD Recorder+VCR, then

press and hold

CH (v/V) on the front panel for about five seconds to change the RF output channel (CH 03 or CH 04). “RF-03” or “RF-04” appears on the front panel display.

Audio/Video Connection

Connect the VIDEO OUT jack on the DVD Recorder+VCR to the video in jack on your TV using the supplied video cable (V).

Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the supplied audio cables

(A).

S-Video Connection

Connect the S-VIDEO OUT jack on the DVD Recorder+VCR to the S-Video in jack on your TV using an S-Video cable (S).

Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the supplied audio cables

(A).

Component Video Connection

Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD Recorder+VCR to the corresponding in jacks on your TV using a Y Pb Pr cable (C).

Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the supplied audio cables

(A).

Progressive Scan Connection



If your television is a high-definition or “digital ready” television, you may take advantage of the DVD Recorder+VCR’s Progressive Scan output for the highest video resolution possible.



If your TV does not accept the Progressive Scan format, the picture will appear scrambled.

Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD Recorder+VCR to the corresponding in jacks on your TV using an optional Y Pb Pr cable (C).

Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the supplied audio cables

(A).

otes

– Be sure to set the Progressive Scan option to “ON” in

the General settings menu; see page 20.

– Progressive Scan does not work with the RF,

Audio/Video or S-Video connections.

Rear of TV

ANTENNA

S-VIDEO

INPUT

S AV C

VIDEO INPUT

AUDIO INPUT

COMPONENT/PROGRESSIVE VIDEO INPUT

Rear of DVD Recorder+VCR

Connections (Continued)

Connecting an Amplifier/Receiver

Connecting to an amplifier equipped with two channel analog stereo or Dolby Pro Logic ll/ Pro Logic

Connect the Left and Right AUDIO OUT jacks on the DVD Recorder+VCR to the left and right audio in jacks on your amplifier, receiver, or stereo system, using the supplied audio cables (A).

Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/ Video receiver equipped with a multi-channel decoder (Dolby Digital™, MPEG 2, or DTS)

Connect one of the DVD Recorder+VCR’s DIGITAL AUDIO OUT jacks (OPTICAL O or COAXIAL X) to the corresponding in jack on your amplifier. Use an optional digital (optical O or coaxial X) audio cable.

You will need to activate the DVD Recorder+VCR’s digital output; see “AUDIO Settings” on page 21.

Digital Multi-Channel Sound

A digital multi-channel connection provides the best sound quality. For this you need a multi-channel audio/video receiver that supports one or more of the audio formats supported by your DVD Recorder+VCR (MPEG 2, Dolby Digital and DTS). Check the receiver manual and the logos on the front of the receiver.

Caution:

Due to the DTS Licensing agreement, the digital output will be in DTS digital out when DTS audio stream is selected.

otes

–

If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all.

– 5.1 channel digital surround sound via the digital con-

nection can only be obtained if your receiver is equipped with a digital multi-channel decoder.

–To see the audio format of the current DVD on the on-

screen display, press AUDIO.

ote

The DVD Recorder+VCR does not perform internal (2channel) decoding of DTS sound tracks. To enjoy DTS multi-channel surround, you must connect the DVD Recorder+VCR to a DTS compatible receiver via one of the DVD Recorder+VCR’s digital audio outputs.

DIGITAL INPUT

Amplifier (Receiver)

Rear of DVD Recorder+VCR

A XO

OPTICAL

AUDIO INPUT DIGITAL INPUT

COAXIAL

CONNECTIONS & SETUP

Connecting Optional Equipment

Connect the AV 1 IN or AV 2 IN jacks on the DVD Recorder+VCR to the audio/video out jacks on your external component, using optional audio/video cables.

ote

If you use the S-VIDEO jack on the front panel, there will be no signal output from the front panel VIDEO jack.

Connecting a Digital Camcorder

Using the front panel DV IN jack, it is possible to connect a DV digital camcorder, video deck or DVD-R/RW recorder and digitally transfer DV tapes or DVD-R/RW discs to DVD-R/RW.

Use a DV cable (not supplied) to connect the DV in/out jack of your DV camcorder/video deck to the front panel DV IN jack of the DVD Recorder+VCR.

ote

This jack is for connection to DV equipment only. It is not compatible with digital satellite tuners or D-VHS video decks.

Connections (Continued)

DV Digital Camcorder

IN/OUT

Front of DVD Recorder+VCR

Setup Menu Overview

The DVD Recorder+VCR Setup menu includes system settings in six categories GENERAL, LANGUAGE, AUDIO, LOCK, RECORD and DISC. Press SETUP on the remote control to view the first and second levels of the Setup menu, and press B to display the third level . You will see the “B” symbol on the right side of the menu label whenever additional levels are available.

Setup Menu Navigation

Press SETUP.

The Setup menu appears.

Use v / V to select the desired option.

While the desired item is selected, press B to move to the second level.

Use v / V to select the second desired option.

Press B to move to the third level.

Use v / V to select the desired setting then press ENTER to confirm your selection.

Some items require additional steps. Press b or RETURN (O) at any time to return to the previous menu.

Press SETUP to exit the Setup menu.

GENERAL Settings

Tuning Band

Press SETUP.

The Setup menu appears.

Use v / V to select the GENERAL option.

While the GENERAL option is selected, press B to move to the second level.

Use v / V to select the Tuning Band option.

Press B to move to the third level.

Use v / V to select the tuning band option (TV or CATV) then press ENTER.

TV: If you are using a standard antenna to receive channels. CATV: If you are using basic cable to receive channels.

Auto Channel Set

The DVD Recorder+VCR is equipped with a frequency synthesized tuner capable of receiving up to 181 channels. These include VHF channels 2-13, UHF channels 14-69 and CATV channels 1-125.

Preparation:



Connect the DVD Recorder+VCR to the desired type of antenna or cable TV system, as shown in “Connecting Antenna/Cable” on page 14

Press SETUP.

The Setup menu appears.

Use v / V to select the GENERAL option.

While the GENERAL option is selected, press B to move to the second level.

Use v / V to select the Auto Channel Set option.

Press B to move to the third level.

The Start icon is highlighted.

Press ENTER to begin the channel search.

The tuner will automatically search for all available channels in your area and place them in the tuner’s memory.

ote

After the Auto Channel Set is complete, follow the instructions at left to make sure the Tuning Band is set correctly (TV or CATV).

Initial Setup

Tuning Band

Auto Channel Set

CH. Add/Del

Clock Set

TV Aspect

Progressive Scan

Factory Setting

CATV

Prev. Select Close

Tuning Band

Auto Channel Set

CH. Add/Del

Clock Set

TV Aspect

Progressive Scan

Factory Setting

11%

Stop

Prev. Select Close

Channel Add/Delete

This feature allows you to manually add or delete channels from your channel list.

Follow steps 1-3 as shown under Auto Channel Set.

Use v / V to select the CH. Add/Del option.

Press B to move to the third level.

The Edit icon is highlighted.

Press ENTER.

The Channel Edit menu appears.

Use v / V or 0-9 to select a channel to add or delete then press B.

The Add or Delete icon is highlighted.

Press ENTER to confirm your setting.

Repeat steps 5-6 to add or delete additional channels.

Press SETUP or RETURN to exit the menu.

Clock (Auto)

The DVD Recorder+VCR gives you two ways to set the time and date: Auto or Manual. Auto is the default setting and enables the DVD Recorder+VCR to set the clock whenever the DVD Recorder+VCR is off or in Standby mode.

Press SETUP.

The Setup menu appears.

Use v / V to select the GENERAL option.

While the GENERAL option is selected, press B to move to the second level.

Use v / V to select the Clock Set option.

Press B to move to the third level.

Use v / V to select the Auto option then press ENTER.

The Auto option is set at the factory. In the Auto option, the DVD Recorder+VCR looks for a channel carrying XDS (Extended Data Services) information. XDS updates the clock using the Coordinated Universal Time.

Use v / V to choose your Time Zone.

You can set your local Time Zone manually. When Time Zone is set to Auto, the DVD Recorder+VCR will use XDS information to determine the proper setting.

Use B to choose the Daylight Saving option. Use v / V to choose Auto, On, or Off.

You can turn Daylight Savings On or Off manually. When set to Auto, the DVD Recorder+VCR will use XDS information to determine the proper setting.

Press ENTER to confirm your setting, then press SETUP to exit the Setup menu.

ote

If your local TV station does not send date and time information, or sends incorrect information, you can

set the clock man-

ually.

Clock (Manual)

Follow steps 1-5 as shown under Clock (Auto).

Use v / V to select the Manual option then press ENTER.

Enter the necessary information for date and time.

b / B (left/right): Moves the cursor to the previous or next column.

v / V (up/down): Changes the setting at the current cursor position.

Press ENTER to confirm your setting, then press SETUP to exit the Setup menu.

CONNECTIONS & SETUP

Initial Setup (Continued)

Tuning Band

Auto Channel Set

CH. Add/Del

Clock Set

TV Aspect

Progressive Scan

Factory Setting

Time Zone

Manual

Auto

Daylight Savings

Auto

Prev. Select Close

Tuning Band

Auto Channel Set

CH. Add/Del

Clock Set

TV Aspect

Progressive Scan

Factory Setting

Manual

Auto

Year Date

Time

2004

Ch. 2

Delete

Add

0-9 Input

Return

Initial Setup (Continued)

TV Aspect Ratio

4:3 Letterbox: Select when a standard 4:3 TV is con-

nected. Displays theatrical images with masking bars above and below the picture. 4:3 Fullscreen: Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen. Both sides of the picture are cut off. 16:9 Widescreen: Select when a 16:9 widescreen TV is connected.

Progressive Scan

Progressive Scan Video provides the highest picture quality with reduced flickering.

• If you are using the COMPONENT/PROGRESSIVE VIDEO OUT jacks, but are connecting the DVD Recorder+VCR to a standard (analog) television, set Progressive Scan to OFF.

• If you are using the COMPONENT/PROGRESSIVE VIDEO OUT jacks for connection to a TV or monitor that is compatible with a Progressive Scan signal, set Progressive Scan to ON.

Caution

Once the setting for Progressive Scan output is entered, an image will only be visible on a Progressive Scan compatible TV or monitor. If you set Progressive Scan to ON in error, you must reset the DVD Recorder+VCR. First, remove the disc in the DVD Recorder+VCR. Next, press STOP (x) and hold it for five seconds before releasing it. The video output will be restored to the standard setting, and a picture will once again be visible on a conventional analog TV or monitor.

Factory Setting

If you wish, you can reset the DVD Recorder+VCR to its original factory settings. Select “SET” then press ENTER. The Initialize menu will appear. Use the b B buttons to select “Yes” and press ENTER.

ote

Some options cannot be reset, including Movie Rating, Password, and Country Code.

LANGUAGE Settings

Display Menu Language

Select a language for the DVD Recorder+VCR Setup menu and on-screen displays.

Disc Menu/Audio/Subtitle Language

Select your preferred language for Disc Menus, Audio soundtracks, and Subtitles.

Original: The disc’s default language is selected. Other: To select another language, select Other then press

ENTER. Use the 0-9 and ENTER buttons to input the corresponding 4-digit number according to the “Language Code List” on page 59. If you a mistake before pressing ENTER, press b to move the cursor back and correct it.

Tuning Band

Auto Channel Set

CH. Add/Del

Clock Set

TV Aspect

Progressive Scan

Factory Setting

Prev. Select Close

4:3 Letterbox

4:3 Fullscreen

16:9 Widescreen

Tuning Band

Auto Channel Set

CH. Add/Del

Clock Set

TV Aspect

Progressive Scan

Factory Setting

OFF

Tuning Band

Auto Channel Set

CH. Add/Del

Clock Set

It initializes the system status.

TV Aspect

Proceed?

Progressive Scan

Yes

Factory Setting

Prev. Select Close

SET

Display Menu

Disc Menu

Disc Audio

Disc Subtitle

Prev. Select Close

English

Prev. Select Close

Display Menu

Disc Menu

Disc Audio

Disc Subtitle

Prev. Select Close

Original

English

French

Italian

Japanese

Spanish

Chinese

Other

- - - -

+ 46 hidden pages