GoVideo VR2945 User Manual

DVD Recorder + VCR

VR2945

User Manual



DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지A

INTRODUCTION

Important Safeguards

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated ‘dangerous voltage‘ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION

POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

WARNING:

Do not install this equipment in a confined space such as a bookcase or similar unit.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

CAUTION:

This DVD Recorder+VCR employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference. Should the DVD Recorder+VCR require maintenance, contact an authorized service center. Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

CAUTION:

The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

FCC WARNING:

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT CLASSE 1 PRODUIT LASER

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지1

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S

MANUAL AND THOSE MARKED ON THE PRODUCT. RETAIN THIS MANUAL FOR FUTURE REFERENCE.

This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.

This product does not contain any parts that can be repaired by the user. DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

Important Safeguards

IMPORTANT SAFETY INSTRUCTIONS

REGULATORY INFORMATION: FCC Part 15

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the product and receiver.

- Connect the product into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC COMPLIANCE:

The responsible party for this product’s compliance is: GoVideo, 7835 East McClain Drive, Scottsdale, AZ 85260, USA.

SERIAL NUMBER:

The serial number is found on the back of the DVD Recorder+VCR. This number is for this unit only. You should record requested information here and retain this guide as a permanent record of your purchase.

Model No. ___________________________________ Serial No. ___________________________________

1 Read these instructions.

All these safety and operating instructions should be read before the product is operated.

2 Keep these instructions.

The safety, operating and use instructions should be retained for future reference.

3 Heed all warnings.

All warnings on the product and in the operating instructions should be adhered to.

4 Follow all instructions.

All operating and use instructions should be followed.

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지2

INTRODUCTION

5 Do not use this product near water.

For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; or near a swimming pool; and other areas located near water.

6 Clean only with dry cloth.

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatuses (including amplifiers) that produce heat.

Make sure that rating of your household electricity supply matches that shown on the back of your product.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the product.

Only use attachments/accessories specified by the manufacturer.

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with apparatus. When a cart is used, use caution when moving the cart/ product combination to avoid injury from tip-over.

Unplug this product during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as: Power-supply cord or plug is damaged; liquid has been spilled or objects have fallen into the product; the product has been exposed to rain or moisture, does not operate normally, or has been dropped.

Do not connect the product to the power supply if you have just moved it from a cold environment to a warm room. This can lead to condensation inside the product, which can damage it. Wait for approximately 2 hrs for it to reach room temperature.

Make sure the product is placed at least 4 inches (10 cm) apart from other home appliances or obstacles to ensure sufficient ventilation.

This product is designed to work continuously. Switching if off does not disconnect if from the power outlet. To disconnect if from the power outlet you have to unplug it.

Important Safeguards

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지3

Table of Contents

Important Safeguards _________________________1 Table of Contents ______________________________4 Overview ______________________________________5 Identification of Controls_______________________10

INTRODUCTION

Connecting Antenna/Cable ____________________15 Connecting a TV _______________________________16 Connecting an Amplifier/Receiver _____________18 Connecting Optional Equipment ______________19 Connecting a Digital Camcorder ______________19

CONNECTIONS

Initial Installation ______________________________20 Initial Setup____________________________________22

Setup Menu Overview 22 Menu Navigation 22 INSTALLATION Settings 22 RECORDING OPTIONS Settings 25 LANGUAGE Settings 26 PREFERENCE / Video Settings 27 PREFERENCE / Audio Settings 28 PREFERENCE / Parental Controls 30 Various PREFERENCE Settings 32 System Information 34 Restore Defaults 34

On-Screen Display Overview __________________35

SETUP

DVD Playback _________________________________38 VCR Playback _________________________________41 Other Disc Playback __________________________43

PLAYBACK

Basic Recording________________________________45

Recording from TV 45 One Touch Record (OTR) 46 Checking the Recording Time 46 To Pause the Recording 46 One Touch Copy - DVD to VHS 47 One Touch Copy - VHS to DVD 48

Timer Recording _______________________________49 Recording from an External Input _____________51

RECORDING

DISC Initialize __________________________________53 Disc Menu _____________________________________53 Title Menu _____________________________________57 Editing _________________________________________59

EDITING

Troubleshooting _______________________________61 Technical Specifications ________________________64

REFERENCE

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지4

INTRODUCTION

Overview

DVD, DVD+R, DVD+RW?

What is a DVD?

DVD (Digital Versatile Disc) is a storage medium that combines the convenience of the compact disc with the latest digital video technology. DVD video uses modern MPEG2 data compression technology that enables an entire feature film to be stored on a single five inch disc.

How good is the resolution of DVD compared with VHS?

The razor-sharp digital images have more than 500 lines of resolution at 720 pixels per line. This is more than twice as high as VHS and even better than laser disc quality. DVD picture quality is easily comparable to the digital masters produced in recording studios.

What is a DVD+RW?

DVD+ReWritable uses ‘phase change‘ media, the same technology on which rewritable CDs are based. A highperformance laser is used to change the reflective properties of the recording layer; this process can be repeated more than a thousand times.

What is a DVD+R?

Unlike a DVD+RW disc, a DVD+R (write-once DVD) can only be written to once. If it is not finalized after a recording, further recordings can be added to it. Old recordings can be deleted but they can no longer be overwritten. The deleted recordings (titles) are marked 'deleted title'.

Before a DVD+R can be played in a DVD player, it must be finalized in the DVD Recorder+VCR. Once this process is complete, no further recordings can be added.

What can I do with my DVD Recorder+VCR?

Your DVD Recorder+VCR is a machine for recording and playing back digital video discs with ‘two-way‘ compatibility with the universal DVD video standard. This means:

• existing DVD video discs can be played on the recorder.

• recordings made on your DVD Recorder+VCR can be played on other DVD video players and DVD-ROM drives.

Regional code

If the region number on your DVD disc does not correspond to the region number of this player, the disc cannot be played.

ALL

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지5

Overview

Disc-related Terms

Title (DVD only)

The main film, accompanying feature content, or music album. Each title is assigned a title reference number enabling you to locate it easily.

Chapter (DVD only)

Sections of a movie or a musical piece that are smaller than titles. A title is composed of one or several chapters. Each chapter is assigned a number to enable you to easily locate the chapter you want. Depending on the disc, chapters may not be labeled.

Track (Audio CD only)

Sections of a movie or a musical piece on an audio CD. Each track is assigned a number, enabling you to easily locate the track you want.

Which discs you can use

The following discs can be used in your DVD Recorder+VCR:

Playback and recording

DVD+RW (Digital Versatile Disc + ReWritable) DVD+R (Digital Versatile Disc + Write-Once)

Playback only

DVD Video (Digital Versatile Disc) DVD-R (DVD-Recordable): These discs can only be played back if the recording was made in ‘Video mode‘ and

the recording was finalized. DVD-RW (DVD-Rerecordable): These discs can only be played back if the recording was made in ‘Video mode‘

and the recording was finalized. Audio CD (Compact Disc Digital Audio) CD-R (CD recordable) Audio/ MP3 files CD-RW (CD rewritable) Audio/ MP3 files

• Not all recordable CDs may be played by your player.

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지6

INTRODUCTION

Overview

Notes on Recording

• The recording times shown are not exact because the DVD Recorder+VCR uses variable bit-rate video compression. This means that the exact recording time will depend on the material being recorded.

• When recording a TV broadcast, if the reception is poor or the picture contains interference, the recording times may be shorter.

• Discs recorded at high speeds (equal to or greater than 2X) may not be recognized.

• If you record still pictures or audio only, the recording time may be longer.

• The displayed times for recording and time remaining may not always add up to the exact length of the disc.

• The available recording time may decrease if you heavily edit a disc.

• When using a DVD+R disc, you can keep recording until the disc is full, or until you finalize the disc. Before you start a recording session, check the amount of recording time left on the disc.

Recording TV Audio Channels

The DVD Recorder+VCR can record one or two channel audio. For TV broadcasts, this usually means mono or stereo, but some programs are broadcast with a main and a SAP (Secondary Audio Program) audio channel. You can record either the main audio or the SAP audio.

Restrictions on Video Recording

• You cannot record copy-protected video using this DVD Recorder+VCR. Copy-protected video includes DVDVideo discs and some satellite broadcasts. If copy-protected material is encountered during a recording, recording will pause or stop automatically and an error message will be displayed on-screen.

• Video that is ‘copy-once only’ can only be recorded using DVD+RW discs with CPRM.

• Audio and video recordings you make using the DVD Recorder+VCR are for your personal use only. You may not sell, lend, or rent them to other people.

• This product incorporates copyright protection technology that is protected by method claims of certain U.S.patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision corporation. Reverse engineering or disassembly is prohibited.

About DVD Recording

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지7

Overview

Handling the Unit

When shipping the unit

The original shipping carton and packing materials come in handy. For maximum protection, re-pack the unit as it was originally packaged at the factory.

When setting up the unit

The picture and sound of a nearby TV, VCR, or radio may be distorted during playback. In this case, position the unit away from the TV, VCR, or radio, or turn off the unit after removing the disc.

To keep the surface clean

Do not use volatile liquids, such as insecticide spray, near the unit. Do not leave rubber or plastic products in contact with the unit for a long period of time. They will leave marks on the surface.

Cleaning the Unit

To clean the cabinet

Use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit.

To obtain a clear picture

The DVD Recorder+VCR is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality will be poor. Regular inspection and maintenance are recommended after every 1,000 hours of use. (This depends on the operating environment.) For details, please contact your nearest dealer.

Remote Control Operation Range

Point the remote control at the remote sensor and press the buttons. Distance: Within 23 ft (7 m) of the remote sensor. Angle: Within 30° in each direction of the remote sensor.

Remote Control Battery Installation

Detach the battery cover on the rear of the remote control, and insert two AAA batteries. Make sure the polarities (+ and -) are aligned correctly.

Caution

Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.).

Precautions

DF-L72B1N-BS(GB) 04.7.1 5:22 AM 페이지8

INTRODUCTION

Overview

Handling Discs

Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints will not get on the surface. Do not stick paper or tape on the disc.

Storing Discs

After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat, or leave it in a parked car exposed to direct

sunlight, as there may be a considerable temperature increase inside the car.

Cleaning Discs

Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center outward.

Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.

Notes on Discs

About the Symbol

‘ ‘ may appear on the TV screen during operation. This icon means the function explained in this User's Guide is not available on that specific disc.

About Symbols

NoYes

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지9

Identification of Controls

POWER

Turns the DVD Recorder+VCR on and off. Lock/Unlock the front panel and Remote control by pressing and holding it over 5 seconds.

Cassette Compartment (VCR deck)

Insert a video cassette here.

EJECT (VCR)

Ejects the tape in the VCR deck.

Disc Tray (DVD deck)

Insert a disc here.

EJECT (DVD)

Opens or closes the disc tray.

ONE TOUCH COPY

Copies from DVD to VCR (or from VCR to DVD).

PLAY/PAUSE

Starts playback of a disc or tape. Pauses playback or recording temporarily.

STOP

Stops playback.

(

REW

DVD: Skips to previous chapter. VCR: Rewinds the tape during Stop mode. Press

during Play mode for fast reverse picture search.

)

DVD: Skips to next chapter. VCR: Advances the tape during Stop mode. Press

during Play mode for fast forward picture search.

DVD/VCR

Toggles control between the DVD deck and the VCR deck.

Front Panel Display

Shows the current status of the DVD Recorder+VCR.

CH †/…

Scans up or down through memorized channels. Also moves up and down in DVD navigation menus.

REC

Starts recording. Press repeatedly to set the recording time. Lights red when the DVD Recorder+VCR is recording.

LINE 1 (VIDEO, L-AUDIO-R)

Connects to the audio/video output of an external source (VCR, Camcorder, etc.).

DV IN

Connects to the DV output of a digital camcorder, video deck, or DVD+R/RW recorder.



! @ # $ %

^ 3 5

&*() 1 2 4 6

Front Panel

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지10

INTRODUCTION

Identification of Controls

Front Panel Display

! Indicates a VHS tape is inserted in the VCR deck. @ Circle : Indicates the VCR is recording.

Clock : Indicates a VCR Timer Recording is set.

# Indicates that a stereo broadcast is being

received.

$ Indicates when a Second Audio Program (SAP)

broadcast is being received.

% Indicates when the DVD Recorder+VCR is playing

or recording a tape with Hi-Fi sound.

^ Indicates the DVD Recorder+VCR is in TV mode

(as set by the TV/VCR button).

& Indicates the current Repeat mode. * Indicates when the DVD Recorder+VCR is locked. ( Indicates when the DVD Recorder+VCR is

outputting the video signal in Progressive Scan mode.

)

Disc Type indicators

Indicates the type of disc loaded.

1 Circle : Indicates a DVD+R(+RW) is recording.

Clock : Indicates a DVD Timer recording is set.

2 Indicates a disc is inserted in the DVD deck. 3 Indicates the current Recording mode. 4 Indicates AM or PM. 5

Front Panel Display Message

Indicates clock, total playing time, elapsed time, remaining time, title number, chapter/track number, channel, VCR counter, etc.

6 DTS: Indicates a DVD is playing with a DTS

soundtrack. Dolby : Indicates a DVD is playing with a Dolby

Digital soundtrack.

! @ # $ % ^ & * ( ) 1 2

3 4 5 6

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지11

Identification of Controls

Remote Control

Turns the DVD Recorder+VCR on and off.

- Opens and closes the disc tray in DVD mode.

- Ejects the tape in the VCR deck in VCR mode.

Switches the view on your TV to the DVD Recorder+VCR tuner.

Selects DVD mode.

Selects VCR mode.

Switches between the DVD Recorder+VCR tuner and your TV tuner.

Displays or exits the Setup menu.

Displays information about the currently loaded disc, VHS tape, or TV channel.

Edits chapters or splits titles of DVD+R(+RW) discs.

Confirms menu selections.

- œ √…† : Selects menu options.

- CH(+/–) : Selects channels.

Accesses DVD disc menus.

- Selects numbered options in menus.

- Selects TV channels.

- Manually adjusts tracking.

Resets the tape counter in VCR mode.

Starts recording. Press repeatedly to set the recording time. For more details, Refer to One Touch Record (OTR) on page 46.

- Starts playback.

- Pauses playback or recording temporarily. Press again to exit Pause mode.

Stops playback or recording.

- DVD: Searches backward/forward.

- VCR: Rewinds/advances during Stop mode. Press during Play mode for fast reverse/forward picture search.

Increases or decreases the slow motion speed when playing a DVD or VHS tape.

Skips to the next or previous chapter/track.

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지12

INTRODUCTION

Switches the DVD Recorder+VCR input to Tuner, LINE1, LINE2, or DV.

Displays a disc’s Title menu, if available.

Identification of Controls

Selects Recording mode: - DVD : HQ (1hr), SP (2hrs), EP (4hrs) or SLP (6hrs).

- VCR : SP or SLP.

Displays the Timer Recording menu.

Selects an audio language (DVD), audio channel (CD) or audio type (TV).

Selects a subtitle language, if available.

Selects a DVD camera angle, if available.

Enlarges the DVD video image.

Repeats the current chapter, track, title or the entire disc.

Repeats playback between two points (A and B).

Press and hold for 3 seconds to switch between Progressive Scan and Interlace Scan mode.

Searches for a specific title or a chapter.

Progressive Scan Mode

• If your TV supports Progressive Scan, you can view high quality video by setting the DVD Recorder+VCR to Progressive Scan mode. If your TV does not support Progressive Scan, do NOT change to Progressive Scan mode.

If you do so accidentally, press and hold the [P.SCAN] key for 3 seconds to restore normal viewing.

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지13

AC Power Cord

Plug into a power outlet.

AUDIO OUT (L, R)

Connect to a TV or other equipment with audio inputs.

COMPONENT/PROGRESSIVE VIDEO OUT (Y Pb Pr)

Connect to a TV with Component Video (Y Pb Pr) inputs.

AV OUT (VIDEO, L-AUDIO-R)

Connect to a TV with video and audio inputs.

LINE2 (VIDEO, L-AUDIO-R)

Connect to the audio/video outputs of an external source (VCR, Camcorder, etc.).

RF IN (FROM ANT.)

Connect to your antenna or cable TV outlet.

RF OUT (TO TV)

Connect to a TV with an RF coaxial input.

COAXIAL (Digital Audio Out)

Connect to an amplifier with a coaxial digital audio input.

(

S-VIDEO OUT

Connect to a TV with an S-Video Input.

Rear panel

Identification of Controls

! @# $% ^

( * &

Caution

• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the DVD Recorder+VCR.

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지14

S-VIDEO

OUT

DVD & VCR OUT

AUDIO OUT COMPONENT OUT

R

COAXIAL



DIGITAL

AUDIO OUT

Pr

Pb

Y

LINE 2

OUT

R

AUDIO

VIDEO

ANT. IN

RF OUT

INTRODUCTION

Connections

Connecting Antenna/Cable

CONNECTIONS

Disconnect the antenna/cable from the rear of your TV.

Connect this cable to the jack marked RF IN (FROM ANT.) on the rear panel of the DVD Recorder+VCR.

Cable Service Without Cable Box

If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your TV and attach it to the RF IN (FROM ANT.) jack on the rear panel of the DVD Recorder+VCR.

Use the supplied coaxial cable to connect between the DVD Recorder+VCR’s OUT (TO TV) jack and the antenna input jack on your TV. With this connection, you can receive all midband, superband, and hyperband channels (all cable channels).

Cable Service With Cable Box

If a cable box is required in your cable system, follow the instructions shown at right. This hookup permits both TV and DVD Recorder+VCR operation.

To view or record a CATV channel:

Tune the TV to the correct video input channel.

Set the DVD Recorder+VCR to the output channel of the cable box using the [CH …/†] or the [0-9] keys on your DVD Recorder+VCR (e.g., CH3).

Select the channel you wish to view on the cable box.

• There are a variety of ways to connect the DVD Recorder+VCR to your TV and other equipment. Use only one of the connections described below. Whichever TV connection you use will work with all input sources.

• Please refer to the manuals for your TV, VCR, stereo system, or other devices as necessary to make the best connections.

• For better sound reproduction, connect the DVD Recorder+VCR’s AUDIO OUT jacks to the audio in jacks of your amplifier, receiver, stereo, or audio/video equipment. See ‘Connecting an Amplifier/Receiver‘ on page 18.

• If you are using a cable box to tune channels, it is not necessary to run Auto Channel Search as indicated on page

23.

Caution

• Make sure the DVD Recorder+VCR is connected directly to the TV, and the TV is set to the correct video input.

• Do not connect the DVD Recorder+VCR’s AUDIO OUT jack to the phono in jack (record deck) of your audio system.

• Do not connect the DVD Recorder+VCR via your VCR. The DVD image could be distorted by the copy protection system.

OUT

DIGITAL

AUDIO OUT



AUDIO OUT COMPONENT OUT

LINE 2

AUDIO

VIDEO

R

COAXIAL

Y

Pb

Pr

RF OUT

ANT. IN

DVD & VCR OUT

Antenna Antenna

Flat Wire

(300 ohm)

300/75 ohm

Adaptor

(Not supplied)

Cable TV

Wall Jack

OR OR

Rear of DVD Recorder+VCR

OUT

DIGITAL

AUDIO OUT



AUDIO OUT COMPONENT OUT

LINE 2

AUDIO

VIDEO

R

COAXIAL

Y

Pb

Pr

RF OUT

ANT. IN

DVD & VCR OUT

Cable TV

Wall Jack

Back Panel of

Typical Cable Box

Rear of DVD Recorder+VCR

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지15

Choose one of the following TV connections, depending on the capabilities of your equipment.

RF Coaxial Connection

Connect the RF OUT (TO TV) jack on the DVD Recorder+VCR to the antenna in jack on your TV using the supplied coaxial cable (R). If you use this connection, tune your TV to the DVD Recorder+VCR’s RF output channel (CH 3 or 4).

How to set the DVD Recorder+VCR’s RF output channel

Press [SETUP] and select Installation ➝ Modulator

Out to change the RF out channel. For details refer to page 24.

Audio/Video Connection 1

Connect the VIDEO OUT jack on the DVD Recorder+VCR to the video in jack on your TV using the supplied video cable (V).

Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the supplied audio cables (A).

S-Video Connection 1

Connect the S-VIDEO OUT jack on the DVD Recorder+VCR to the S-Video in jack on your TV using an SVideo cable (S).

Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the supplied audio cables (A).

Component Video Connection 1

Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD Recorder+VCR to the corresponding input jacks on your TV using a Y Pb Pr cable (C) if the Component Video jacks (Y, Pb, Pr) are available on your TV.

Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the supplied audio cables (A).

Connecting a TV

Connections

All video signals are available from all video outputs.

That means that whichever TV connection you use, it will

work with all input sources, including VHS out of the Component/Progressive Video Output.

ANTENNA

INPUT

COMPONENT/PROGRESSIVE VIDEO INPUT

AUDIO INPUT

VIDEO INPUT

S-VIDEO

INPUT

Rear of TV

S-VIDEO

OUT

OUT

DIGITAL

AUDIO OUT



AUDIO OUT COMPONENT OUT

LINE 2

AUDIO

VIDEO

R

COAXIAL

Y

Pb

Pr

RF OUT

ANT. IN

DVD & VCR OUT

Rear of DVD Recorder+VCR

S AVC

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지16

CONNECTIONS

Progressive Scan Connection

• If your television is a high-definition or ‘digital ready‘ television, you may take advantage of the DVD Recorder+VCR’s Progressive Scan output for the highest video resolution possible.

• If your TV does not accept the Progressive Scan format, the picture will appear scrambled.

Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD Recorder+VCR to the corresponding in jacks on your TV using an optional Y Pb Pr cable (C).

Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the supplied audio cables (A).

• Be sure to set the DVD Recorder+VCR to Progressive Scan mode by pressing and holding [P.SCAN] for 3 seconds (or changing the Scan Mode in the Setup Menu; see page 27).

• Progressive Scan does not work with the RF, Audio/Video or S-Video connections.

Connections

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지17

Connections

Connecting to an amplifier equipped with two channel analog stereo or Dolby Pro Logic ll/Pro Logic

Connect the Left and Right AUDIO OUT jacks on the DVD Recorder+VCR to the left and right audio in jacks on your amplifier, receiver, or stereo system, using the supplied audio cables (A).

Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/Video receiver equipped with a multi-channel decoder (Dolby Digital™, MPEG 2, or DTS)

Connect the DVD Recorder+VCR’s DIGITAL AUDIO OUT jack (COAXIAL X) to the corresponding in jack on your amplifier. Use an optional digital coaxial audio cable.

You will need to activate the DVD Recorder+VCR’s digital output; see ‘AUDIO Settings‘ on page 28.

Digital Multi-Channel Sound?

A digital multi-channel connection provides the best sound quality. For this you need a multi-channel audio/video receiver that supports one or more of the audio formats supported by your DVD Recorder+VCR (MPEG 2, Dolby Digital, and DTS). Check the receiver manual and the logos on the front of the receiver.

Connecting an Amplifier/Receiver

• Due to the DTS Licensing agreement, the digital output will be in DTS digital out when DTS audio stream is selected.

• If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all.

• 5.1 channel digital surround sound via the digital connection can only be obtained if your receiver is equipped with a digital multi-channel decoder.

• To see the audio format of the current DVD on the on-screen display, press [AUDIO].

The DVD Recorder+VCR does not perform internal (2- channel) decoding of DTS sound tracks. To enjoy DTS multichannel surround, you must connect the DVD Recorder+VCR to a DTS compatible receiver via one of the DVD Recorder+VCR’s digital audio outputs.

Amplifier (Receiver)

AUDIO INPUT DIGITAL INPUT

COAXIAL

S-VIDEO

OUT

OUT

DIGITAL

AUDIO OUT



AUDIO OUT COMPONENT OUT

LINE 2

AUDIO

VIDEO

R

COAXIAL

Y

Pb

Pr

RF OUT

ANT. IN

DVD & VCR OUT

Rear of DVD Recorder+VCR

A X

DF-L72B1N-BS(GB) 04.7.1 3:9 AM 페이지18

CONNECTIONS

Connections

To receive audio/video signals from other equipment, connect the LINE1 or LINE2 jacks on the DVD Recorder+VCR to the audio/video out jacks on your external component, using optional audio/video cables.

Connecting Optional Equipment

OUT

LINE 2

AUDIO

VIDEO

R

RF OUT

ANT. IN

Using the front panel DV IN jack, it is possible to connect a DV digital camcorder, video deck or DVD+R/RW recorder and digitally transfer DV tapes or DVD+R/RW discs to DVD+R/RW.

Use a DV cable (not supplied) to connect the DV In/Out jack of your DV camcorder/video deck to the front panel DV IN jack of the DVD Recorder+VCR.

Connecting a Digital Camcorder

This jack is for connection to DV equipment only. It is not compatible with digital satellite tuners or D-VHS video decks.

DV IN

DV Digital Camcorder

Front of DVD Recorder+VCR

IN/OUT

DF-L72B1N-BS(GB) 04.7.1 3:10 AM 페이지19

After successfully connecting your DVD Recorder+VCR to your TV and other devices, this chapter will show you how to complete the initial installation.

A ‘Welcome‘ message is displayed on the screen. Make sure the RF cable from your antenna or cable TV jack is connected.

Select the desired language for the on-screen menu using […/†]. Press [ENTER] to confirm.

Select the desired disc menu language using […/†]. Press [ENTER] to confirm.

Select the desired disc playback audio language using […/†]. Press [ENTER] to confirm.

Initial Installation

Installation

Please select your language to begin auto install procedure:

English Spanish French

Instructions

Enter-Confirm Setup-Exit Move …†

Installation

Please select disc menu language:

Default English Spanish French Italian Japanese Chinese

Instructions

Enter-Confirm Setup-Exit Move …†

Installation

Please select disc play back audio language:

Default English Spanish French Italian Japanese Chinese Instructions

Enter-Confirm Setup-Exit Move …†

Installation

Welcome.

Press [Enter] to begin auto channel search.

Ensure antenna is connected.

Instructions

Setup-Exit

• You must follow the initial installation process to set the time, date, channels, and language preferences for the DVD Recorder+VCR.

DF-L72B1N-BS(GB) 04.7.1 3:10 AM 페이지20

+ 46 hidden pages