Gotham PDXH, PDXTH User Manual
INSTALLATION INSTRUCTIONS
PDXH - PDXTH
Upon receipt, thoroughly inspect for any
freight damage which should be brought
to the attention of the delivery carrier.
Compare the catalog description listed on
the packing slip with the label on the
carton to ensure that you have received
the correct merchandise.
SAVE THESE INSTRUCTIONS
New Installation
1. Slide both trim mounting brackets under lanced up tabs on the mounting frame
as shown in Figure 1. Brackets may be secured to the mounting frame by screws
or rivets (not supplied). NOTE: REMOVE AND DISCARD FRICTION SUPPORT CLIPS
FROM MOUNTING FRAME IF PRESENT.
2. Remove trim cone by gripping the flange and pulling it out of the reflector.
Disconnect safety chain as shown in Figure 2. Lensed Units Only- Remove lens
by pushing clips holding lens outward, allowing lens to drop below the clips as
shown in Figure 3.
3. Attach socket cup to top of reflector by aligning springs in socket cup with slots
in reflector. Push socket cup down until springs are engaged in slots as seen in
Figure 4.
4. Push reflector through mounting frame opening, aligning key hole slots with
screws in trim mounting brackets. Rotate reflector to engage screws in keyhole
slots and tighten screws securely as shown in Figure 2.
5. Visually inspect reflector flange, making sure it is seated properly against the
ceiling.
6. Install lamp. Ensure lamp type and wattage are correct. Lensed Units Only - Re-
install lens.
7. Re-attach safety chain and re-install lower cone reflector. Ensure flange is
seated tightly against the ceiling.
Trim Mounting
Bracket
IMPORTANT SAFETY INFORMATION
For Your Protection, Read Carefully
WARNING - Risk of fire. Do not install insulation within 3 inches of fixture sides or
wiring compartment, nor above the fixture
in such a manner as to entrap heat.
1. Electric current can cause painful
shock or serious injury unless handled
properly. For your safety, always remember the following:
• Turn off the power supply.
• Ground the fixture to avoid poten-
tial electrical shocks.
• Do not handle an energized fixture
or energize any fixture with wet
hands, when standing on a wet or
damp surface, or in water.
• Double check all electrical connections
to be sure they are tight and correct.
2. Specific safety information concerning lamps:
• Match wattage of fixture and lamp
exactly.
• Do not remove or insert lamp when
power is on.
• Do not scratch glass or subject lamp
to undue pressure as either may
cause lamp breakage.
• Protect operating lamp from sources
of moisture.
• If lamp is marked it contains mercury.
Hg
Follow disposal laws. See:
www.lamprecycle.org.
Key
Slots (2)
Figure 1
Lens Clips (3)
Figure 3 Figure 4
ivynarofkcehC
motpmySesuaCelbissoPnoitcAevitcerroC
OTSLIAFPMAL
THGIL
TUOSEOGPMAL
GNITHGILRETFA
DNA
NOSELCYCPMAL
FFO
TRAHCGNITOOHSELBUORT
.snoitcaevitcerrocdnasesuacelbissopfotsilgniwollofeht
dezigrenetonerutxifehtgnideeftiucriC·
omrotiucricnirorregniriW·
pmalytluaF·
tuptuotsallabroeniL·
tsallabytluaF·
pmalytluaF· naht
wolooterutarepmettneibmA·
erutxifotesolcootsinoitalusnI·
hgihootegattawpmaL·
wolegatlovtuptuotsallaB·
noitcennocelud
ehC·
.tcerroc
enilkcehC·
Trim Cone
ilotnwonksitahteno
.enowenahtiw
.ytiunitnoctiucrickc
rfnoitalusnievomeR·
.gnisuohnideificepsegattawpmalllatsnI·
Figure 2
nimelborpehtetacol,noitidnocdoognimeesyehtfI.eludomni-emarfropmalehtotegamadelbis
renesitiucrictahterusneotesufrorekaerbtiucrickcehC·
erasnoitcennoctahterusneotxobecilpserutxifenimaxE·
.egatlovtiucricnepokcehC.erutxiftaegatlovenilkcehC·
rehtarmotpmyssihttibihxelliwpmalayllanoisaccO·
.pmalwenaetutitsbuS.thgilotgniliafylpmis
)"3tsaelta(eludomdnuoramo
.egatlovtiucricnepokcehC.erutxifehttaegatlov
.dezig
ylbareferp,pmalrehtonaetutitsbusdnapmalytluafehtevomeR·
lanigiroehtecalper,sthgilpmalehtfI.thg
.snoitidnoclatnemnorivnegnitsixetsniagagnitartsallabkcehC·
Part No. CJ520716
©2007 Gotham, 05/07
Loading...