INSTALLATION INSTRUCTIONS
GRSF
Emergency Ballast with
Integral or Remote Test
Switch
Upon receipt, thoroughly inspect for any
freight damage which should be brought to
the attention of the delivery carrier. Compare
the catalog description listed on the packing
slip with the label on the carton to ensure you
have received the correct merchandise.
IMPORTANT SAFETY INFORMATION
For Your Protection, Read Carefully
WARNING - Risk of fire. Do not install insulation within 3 inches of fixture sides or wiring
compartment, nor above the fixture in such
a manner as to entrap heat.
1. Electric current can cause painful shock
or serious injury unless handled properly.
For your safety, always remember the following:
• Turn off the power supply.
• Ground the fixture to avoid potential
electrical shocks.
• Do not handle an energized fixture or
energize any fixture with wet hands,
when standing on a wet or damp surface, or in water.
• Double check all electrical connections
to be sure they are tight and correct.
2. Specific safety information concerning
lamps:
• Match wattage of fixture and lamp exactly.
• Do not remove or insert lamp when power
is on.
• Do not scratch glass or subject lamp to
undue pressure as either may cause
lamp breakage.
• Protect operating lamp from sources
of moisture.
Figure 1
Figure 2
Figure 2
Prior to Installation
1. Install rough-in section as detailed on separate instruction
sheet.
2. Determine line voltage to fixture
(switched and unswitched
power requirements).
3. Verify correct ballast/lamp combination.
Installation
1. Pivot emergency ballast assembly onto mounting rails of roughin section as shown in Figure 1.
Make any necessary vertical
adjustments to assure that the
bottom of the rough-in section is
flush or slightly above (1/8" max.)
the ceiling line.
2. Feed power supply to fixture as
detailed in separate instruction
sheet. Attach flex with junction
box cover from Emergency Ballast assembly to junction box
and make necessary wire connections.
ivynarofkcehC
motpmySesuaCelbissoPnoitcAevitcerroC
OTSLIAFPMAL
THGIL
TUOSEOGPMAL
GNITHGILRETFA
DNA
NOSELCYCPMAL
FFO
TRAHCGNITOOHSELBUORT
omrotiucricnirorregniriW·
pmalytluaF·
tuptuotsallabroeniL·
tsallabytluaF·
pmalytluaF· naht
wolooterutarepmettneibmA·
erutxifotesolcootsinoitalusnI·
hgihootegattawpmaL·
wolegatlovtuptuotsallaB·
For Integral Test Switch:
3. Drop socket housing through roughin section opening.
4. Install integral test switch and reflector as detailed on separate instruction sheet.
For Remote Test Switch:
3. Select location near rough-in section
for mounting junction box (attached
to emergency ballast assembly) that
will house the remote test switch/
charging indicator light cover plate.
Cut hole in ceiling using junction box
as a reference as shown in Figure 2
(approximate size required: 2" x 31/4").
Secure junction box in hole.
IMPORTANT: Before cutting hole,
verify that junction box will reach
preferred location and will not interfere with any part of the rough-in
section.
4. Remote test switch/charging indicator light cover plate may now be installed by aligning plug connector
with mating connector inside junction
box and snapping the two together.
Use screws provided to secure cover
plate to junction box.
IMPORTANT: When connectors are
plugged together, the fixture circuit
is completed. If power to fixture is
turned off, the batteries inside the
emergency ballast assembly will discharge. Frequent power interruptions may result in premature failure
of the batteries.
.snoitcaevitcerrocdnasesuacelbissopfotsilgniwollofeht
dezigrenetonerutxifehtgnideeftiucriC·
noitcennocelud
.tcerroc
ilotnwonksitahteno
.enowenahtiw
ehC·
enilkcehC·
.ytiunitnoctiucrickc
.pmalwenaetutitsbuS.thgilotgniliafylpmis
rfnoitalusnievomeR·
.gnisuohnideificepsegattawpmalllatsnI·
nimelborpehtetacol,noitidnocdoognimeesyehtfI.eludomni-emarfropmalehtotegamadelbis
.dezig
renesitiucrictahterusneotesufrorekaerbtiucrickcehC·
erasnoitcennoctahterusneotxobecilpserutxifenimaxE·
ylbareferp,pmalrehtonaetutitsbusdnapmalytluafehtevomeR·
lanigiroehtecalper,sthgilpmalehtfI.thg
.egatlovtiucricnepokcehC.erutxiftaegatlovenilkcehC·
.snoitidnoclatnemnorivnegnitsixetsniagagnitartsallabkcehC·
rehtarmotpmyssihttibihxelliwpmalayllanoisaccO·
)"3tsaelta(eludomdnuoramo
.egatlovtiucricnepokcehC.erutxifehttaegatlov
Part No. CJ520490
Rev. B 05/04
Loading...