DFRRegressed lensed white painted trim
DFFFlush lensed white painted trim
DFRBRRegressed lensed black painted trim
DFFBRFlush lensed black painted trim
DFRAMFRegressed lensed trim with anti-mi-
crobial finish
DFFAMFFlush lensed trim with anti-microbial
finish
SOLTextured Lens
SMOSmooth Clear Lens
353500 lumens
404000 lumens
1
Driver
EZ10eldoLED 0-10V ECOdrive. Linear
dimming to 10% min.
EZ1eldoLED 0-10V ECOdrive. Linear
dimming to 1% min.
EZBeldoLED 0-10V SOLOdrive.
Logarithmic dimming to <1%.
EDABeldoLED SOLOdrive DALI. Loga-
rithmic dimming to <1%.
Control InterfaceOptions
2
NLT
NLTER
nLight dimming pack controls
2,3
nLight dimming pack controls
emergency circuit
SFSingle fuse. Specify 120V or 277V.
4
ELR
E10WCPR
BGTDBodine generator transfer device. Specify 120V or 277V.
90CRIHigh CRI (90+).
CPChicago Plenum.
Emergency battery pack, 10W, with remote test switch.
4
Emergency battery pack, 10W Constant Power, CA Title 20
compliant with remote test switch
MVOLT
120
277
ACCESSORIES — order as separate catalog numbers (shipped separately)
ISD BC
0-10V wallbox dimmer. Refer to ISD-BC.
ORDERING NOTES
1. Refer to TECH-240 for compatible dimmers.
2. Specify voltage.
3. For use with generator supply EM power. Will require an emergency
hot feed and normal hot feed.
Fully serviceable and upgradeable lensed LED light engine suitable for field maintenance or service from below the ceiling.
Unitized optics shall have mechanical attachment of the light engine to the lower reflector for complete optical alignment.
General Illumination Square Cleanroom Downlight
Electrical
The luminaire shall operate from a 50 or 60 Hz ±3 Hz AC line over a voltage ranging from 120 VAC to 277 VAC. The fluctuations of line voltage shall have no
visible effect on the luminous output.
The luminaire shall have a power factor of 90% or greater at all standard operating voltages and full luminaire output.
Sound Rated A+. Driver shall be >80% efficient at full load across all input voltages.
Input wires shall be 18AWG, 300V minimum, solid copper.
Controls
Luminaire shall be equipped with interface for nLight wired network with integral power supply as per specification.
Dimming
The luminaire shall be capable of continuous dimming without perceivable stroboscopic flicker as measured by flicker index (ANSI/IES RP-16-10) over a range
of 100 – 10%, 100 – 1.0% or 100 – 0.1% of rated lumen output with a smooth shut off function to step to 0%.
eldoLED LED drivers shall conform to IEEE P1789 standards. Alternatively, manufacturers must demonstrate conformance with product literature and testing
which demonstrates this performance. Systems that do not meet IEEE P1789 will not be considered.
Driver is inaudible in 24dB environment, and stable when input voltage conditions fluctuate over what is typically experienced in a commercial environment.
Construction
Luminaire housing shall be constructed of 16-gauge galvanized steel and have preinstalled telescopic mounting bars with maximum 32” and minimum 15”
extension and 4” vertical adjustment.
Luminaires shall be suitable for installation in ceilings up to 1½” thick.
Tool-less adjustments shall be possible after installation.
The assembly and manufacturing process for the luminaire shall be designed to assure all internal components are adequately supported to withstand mechanical shock and vibration.
25°C ambient temperature standard (1/2” clearance on all sides from non-combustible materials in non-IC applications, unless marked spacing noted
otherwise). For use in insulated ceilings, a 3" clearance on all sides from insulation is required (unless marked spacing noted otherwise).
Listings
Fixtures are CSA certified to meet US and Canadian standards: All fixtures manufactured in strict accordance with the appropriate and current requirements of
the “Standards for Safety” to UL, wet location covered ceiling.
Photometrics
LEDs tested to LM-80 standards. Measured by IESNA Standard LM-79-08 in an accredited lab. Lumen output shall not decrease by more than 30% over the
minimum operational life of 60,000 hours.
Color appearance from luminaire to luminaire of the same type and in all configurations, shall be consistent both initially and at 6,000 hours and operate within a tolerance of <2.5 MacAdam ellipse as defined by a point at the intersection of the CCT line and the black body locus line in CIE chromaticity space.
Buy American
This product is assembled in the USA and meets the Buy America(n) government procurement requirements under FAR, DFARS and DOT.
Please refer to www.acuitybrands.com/buy-american for additional information.
Warranty
5-year limited warranty. Complete warranty terms located at: www.acuitybrands.com/support/customer-support/terms-and-conditions
Note:
Actual performance may differ as a result of end user environment and application.
All values are design or typical values, measured under laboratory conditions at 25 °C.
Capable Luminaire
This item is an A+ capable luminaire, which has been designed and tested to provide consistent color appearance and out-of-the-box control compatibility with simple commissioning.
• All configurations of this luminaire meet the Acuity Brands’ specification for chromatic consistency
• This luminaire is part of an A+ Certified solution for nLight
• This luminaire is part of an A+ Certified solution for nLight
options marked by a shaded background*
To learn more about A+, visit www.acuitybrands.com/aplus.
*See ordering tree for details
®
control networks when ordered with drivers marked by a shaded background*
®
control networks, providing advanced control functionality at the luminaire level, when selection includes driver and control
nLight® AIR is the ideal solution for retrofit or new construction spaces where
adding communication wiring is cost prohibitive. The integrated nLight AIR
rPP20 Power Pack is part of each EVO Luminaire ordered with the NLTAIR option.
These individually addressable controls offer the ultimate in flexibility during
initial setup and for space repurposing.
nLight® AIR Control Accessories
Order as separate catalog number. Visit nLight AIR.
Wall Switches
On/Off single pole
On/Off two pole
On/Off & raise/lower single pole
On/Off & raise/lower two pole
®
AIR Control Accessories (cont.)
nLight
Occupancy Sensors (PIR/dual tech)
Small motion 360
Large motion 360
o
, ceiling
o
, ceiling
Model Number
rPODB (color) G2
rPODB 2P (color) G2
rPODB DX (color) G2
rPODB 2P DX (color) G2
Model Number
rCMS 9 / rCMS PDT 9
rCMS 10 / rCMS PDT 10
Possibilites for nLight
®
AIR
Fixtures ordered without the NLTAIR option
Fixtures ordered with the NLTAIR option
CLAIRITYTM Pro
Mobile App
CLAIRITYTM Pro
Mobile App
+24v DC AuxLine Power
rPODBrCMS
rPODB
Wiring Key
rPP20
Low Voltage
Dimming Wires
®
Wired The nLight® solution is a digital networked lighting control
nLight
system that provides both energy savings and increased user configurability
by cost effectively integrating time-based, daylight-based, sensor-based and
manual lighting control schemes.