GZ100-10V driver dims to 10%
GZ10-10V driver dims to 1%
EZ10eldoLED 0-10V ECOdrive. Linear dimming to 10% min.
EZ1eldoLED 0-10V ECOdrive. Linear dimming to 1% min.
EZBeldoLED 0-10V SOLOdrive. Logarithmic dimming to <1%.
5
EDAB
EDXB
ECOS2
ECOD
ELV
eldoLED SOLOdrive DALI. Logarithmic dimming to <1%.
4,5
eldoLED POWERdrive DMX with RDM (remote device management). Square
Law dimming to <1%. Min: 1000LM; Max: 4000LM.
E10WCPREmergency battery pack, 10W Constant Power, CA Title 20
11
CP
compliant with remote test switch (requires RGH)
Chicago Plenum. Specify 120V or 277V (requires RGH)
GTDIOTA Generator Transfer Device. Specify 120V or 277V
(requires RGH)
DWHAMFGloss White with Anti-microbial finish
DDBGloss Dark Bronze
DBLMatte Black
DWHGloss White
DMBMatte Medium Bronze
DNAGloss Natural Aluminum
DSSGloss Sandstone
DGCGloss Charcoal Grey
DTGGloss Tennis Green
DBRGloss Bright Red
DSBGloss Steel Blue
10
DDBTTextured Dark Bronze
DBLBTextured Black
DWHGTextured White
DBNHTextured Bronze
DNATTextured Natural Aluminum
DSSTTextured Sandstone
DSPDTextured Dark Grey
DSPETextured Green
DSPHTextured Light Red
ACCESSORIES — order as separate catalog numbers (shipped separately)
GCOLORS KITArchitectural Colors chip kit, consisting of powder-coat and plated finishes
CYLJBOXADPT 4SQ2OCT __4in Square J-box to 4in Octagonal J-box adaptor. Replace __ with Architectural Color or PRM for primed ready for field painting
ORDERING NOTES
1. Not Available with Finishes.
2. Factory supplied step down transformer must be remote mounted. Access required to location of
remote mounted device.
3. Refer to Tech 240 for compatible dimmers.
4. Includes terminator resistor. Not available with 250-750 lumen packages.
5. Not Available with Control Interfaces.
6. Factory installed with RGH option otherwise field installed. Access required to location of remote
mounted device.
7. ER for use as UL924 Emergency Operation via power sense lead. Will require an emergency hot feed and
normal hot feed. EM for use as UL924 Emergency Operation via power interrupt detection.
8. Only available up to 2500 lumens; up to 2000 lumens wet location. Not available with ECOS2.
9. Not available with JBXCC.
10. For details on RAL and Custom colors please see Architectural colors.
11. CP not valid with NLTAIR2, NLTAIRER2 or E10WCPR.
Fully serviceable and upgradeable lensed LED light engine suitable for field maintenance or service from below the ceiling.
Unitized optics shall have mechanical attachment of the light engine to the lower reflector for complete optical alignment.
Wallwash enables uniformity from floor to ceiling. Smooth, balanced illumination optimized for ceilings of 8’ to 12’ with recommended spacing of 3’ from wall
and 3’ centers.
General Illumination Surface Ceiling Cylinder Wallwash
Electrical
The luminaire shall operate from a 50 or 60 Hz ±3 Hz AC line over a voltage ranging from 120 VAC to 277 VAC. Support 347V via remote-mounted stepdown
transformer. The fluctuations of line voltage shall have no visible effect on the luminous output.
The luminaire shall have a power factor of 90% or greater at all standard operating voltages and full luminaire output.
Sound Rated A+. Driver shall be >80% efficient at full load across all input voltages.
Input wires shall be 18AWG, 300V minimum solid copper.
Controls
Luminaire shall be equipped with interface for nLight wired or nLight AIR networks with integral power supply as per specification.
Emergency
Luminaires supplied with a battery pack comply with NFPA 101 (Life Safety code) and deliver constant light output throughout the 90 minutes of code required emergency operation period when there is a normal AC power loss.
Luminaires equipped with a generator transfer device work in conjunction with an auxiliary generator or a central inverter system to power fixtures for safe
egress lighting.
Dimming
The luminaire shall be capable of continuous dimming without perceivable stroboscopic flicker as measured by flicker index (ANSI/IES RP-16-10) over a range
of 100 – 10%, 100 – 1.0% or 100 – 0.1% of rated lumen output with a smooth shut off function to step to 0%.
eldoLED LED drivers shall conform to IEEE P1789 standards. Alternatively, manufacturers must demonstrate conformance with product literature and testing
which demonstrates this performance. Systems that do not meet IEEE P1789 will not be considered.
Driver is inaudible in 24dB environment, and stable when input voltage conditions fluctuate over what is typically experienced in a commercial environment.
Construction
Heaving-gauge aluminum construction.
Extruded body with flangeless reflector allows flow-through passive thermal management.
Surface ceiling mount for direct installation to 4” recessed or surface octagonal or square junction box.
Optional field configurable conduit covers available. Conduit covers match cylinder in finish and diameter.
Recessed gear box available for driver above ceiling, nLight, CP, GTD or battery pack options.
Listings
Fixtures are CSA Certified to meet US and Canadian Standards: All fixtures manufactured in strict accordance with the appropriate and current requirements of
the “Standards for Safety” to UL, damp location standard; wet location covered ceiling optional (WL); IP66 rating optional (IP66).
Luminaire configurations are Energy Star certified through testing in EPA–recognized laboratories, with the results reviewed by an independent, accredited
certification organization. Some configurations are Energy Star certified. Visit www.energystar.gov for specific configurations listed.
Photometrics
LEDs tested to LM-80 standards. Measured by IESNA Standard LM-79-08 in an accredited lab. Lumen output shall not decrease by more than 30% over the
minimum operational life of 60,000 hours.
Color appearance from luminaire to luminaire of the same type and in all configurations, shall be consistent both initially and at 6,000 hours and operate within a tolerance of <2.5 MacAdam ellipse as defined by the center of the quadrangles defined in ANSI C78.377-2015.
Buy American
This product is assembled in the USA and meets the Buy America(n) government procurement requirements under FAR, DFARS and DOT.
Please refer to www.acuitybrands.com/buy-american for additional information.
Warranty
5-year limited warranty. Complete warranty terms located at: www.acuitybrands.com/support/warranty/terms-and-conditions
Note:
Actual performance may differ as a result of end user environment and application.
All values are design or typical values, measured under laboratory conditions at 25 °C.
Capable Luminaire
This item is an A+ capable luminaire, which has been designed and tested to provide consistent color appearance and out-of-the-box control compatibility with simple commissioning.
• All configurations of this luminaire meet the Acuity Brands’ specification for chromatic consistency
• This luminaire is part of an A+ Certified solution for nLight
• This luminaire is part of an A+ Certified solution for nLight
options marked by a shaded background*
To learn more about A+, visit www.acuitybrands.com/aplus.
*See ordering tree for details
control networks when ordered with drivers marked by a shaded background*
®
control networks, providing advanced control functionality at the luminaire level, when selection includes driver and control
4"
General Illumination Surface Ceiling Cylinder Wallwash
Tables of Use
EVO - eldoLED Driver Default Dimming Curve
NomenclatureMin DimmingDriver Dim CurveControl Dim Curve
EZ1010%LinearLinear/Logarithmic
EZ11%LinearLinear/Logarithmic
EZB<1%LogarithmicLinear
EDAB<1%Logarithmic*Linear
EDXB<1%SquareLinear
*Changable thorugh DALI controller
Driver
(note: 347V/UVOLT versions provided with 347 option selected)
Control Provided
NomenclatureDescriptionNLTNLTERNLTAIR2NLTAIRER2
GZ100-10V driver dims to 10% nPP16 D EFP nPP16 D ER EFPRPP20 D 24V G2RPP20 D 24V ER G2
GZ10-10V driver dims to 1% nPP16 D EFP nPP16 D ER EFPRPP20 D 24V G2RPP20 D 24V ER G2
EZ10eldoLED 0-10V ECOdrivenPS 80 EZnPS 80 EZ ERRPP20 D 24V G2RPP20 D 24V ER G2
EZ1eldoLED 0-10V ECOdrivenPS 80 EZnPS 80 EZ ERRPP20 D 24V G2RPP20 D 24V ER G2
EZBeldoLED 0-10V SOLOdrivenPS 80 EZnPS 80 EZ ERRPP20 D 24V G2RPP20 D 24V ER G2
Lumen Output Multiplier
CRICCTMultplier
2700K0.916
3000K0.948
80
3500K1
4000K1.032
5000K1.1
2700K0.748
3000K0.8
90
3500K0.838
4000K0.845
5000K0.945
J-box Compatibility
Matrix
Recommended
J-box (by others)
4" Octagonal
4x4x1.5 deep"
4" Octagonal
4x4x2.125 deep
4" Square
4x4x1.5 deep
Reflector Finish Multiplier
Reflector FinishMultiplier
LS - Specular 1
LSS - Semi Specular0.956
WR - White0.87
LD - Matte Diffuse0.85
BR - Black0.73
BZR Bronze0.73
Cylinder Configurations
JBX w/EDXB
JBX
Driver
*with adaptor
plate accessory
JBXCC
Standard Architectural Color Options for Cylinder Bodies
DSS P12
LITHONIA
Sandstone
DSB P49
LITHONIA
Steel Blue
DBLB P75
TEXTURED
Black
DSST P90
TEXTURED
Sandstone
DNA P07
LITHONIA
Natural Aluminum
DWH P21
LITHONIA
White
DBR P34
LITHONIA
Bright Red
DNAT P89
TEXTURED
Natural Aluminum
DWHG P86
TEXTURED
White
NOTE: These colors were carefully reproduced to give as true a depiction as possible of finished product
color. Some colors, however, may vary slightly from actual appearance due to display/printing variations and
limitations. Please always contact a Lithonia representative for an accurate paint chip sample.
General Illumination Surface Ceiling Cylinder Wallwash
NLIGHT AIRNLIGHT
nLight® AIR is the ideal solution for retrofit or new construction spaces where
adding communication wiring is cost prohibitive. The integrated nLight AIR
rPP20 Power Pack is part of each EVO Luminaire ordered with the NLTAIR option.
These individually addressable controls offer the ultimate in flexibility during
initial setup and for space repurposing.
nLight® AIR Control Accessories
Order as separate catalog number. Visit nLight AIR.
Wall Switches
On/Off single pole
On/Off two pole
On/Off & raise/lower single pole
On/Off & raise/lower two pole
®
AIR Control Accessories (cont.)
nLight
Occupancy Sensors (PIR/dual tech)
Small motion 360
Large motion 360
o
, ceiling
o
, ceiling
Model Number
rPODB (color) G2
rPODB 2P (color) G2
rPODB DX (color) G2
rPODB 2P DX (color) G2
Model Number
rCMS 9 / rCMS PDT 9
rCMS 10 / rCMS PDT 10
Possibilites for nLight
®
AIR
Fixtures ordered without the NLTAIR option
Fixtures ordered with the NLTAIR option
CLAIRITYTM Pro
Mobile App
CLAIRITYTM Pro
Mobile App
+24v DC AuxLine Power
rPODBrCMS
(ordered as an accessory)
rPODB
Wiring Key
rPP20
Low Voltage
Dimming Wires
®
Wired The nLight® solution is a digital networked lighting control
nLight
system that provides both energy savings and increased user configurability
by cost effectively integrating time-based, daylight-based, sensor-based and
manual lighting control schemes.