• Self-flanged, matte-diffuse high-impact polymer finishing trim with a durable,
proprietary vapor deposition finish.
• Patented Bounding Ray™ Optical Principle design (U.S. Patent No. 5,800,050)
provides lamp before lamp image and smooth transition from top of the reflector
to bottom.
• One piece trim eliminates mitered flange corners and inside corner gaps.
• Upper reflector is painted a highly reflective matte white providing diffuse, even
light with high efficiency.
• Dual kicker design along with proprietary Gotham spread lens delivers a uniform
distribution of light to the wall.
MECHANICAL SYSTEM
• 16-gauge painted steel mounting/plaster frame accommodates up to 1-1/2”
thick ceiling materials.
• Patented adjustable aperture allows 1/4” adjustments in all directions and up
to 5° of rotation allowing post-installation adjustments to ensure trim-to-trim
alignment.
• 16-gauge galvanized steel mounting bars with continuous 4” vertical adjustments are shipped pre-installed. Post-installation adjustment possible without
the use of tools from above or below ceiling.
EXAMPLE: SQFW 1/32TRT 4AR MVOLT
• Secondary housing adjustment system for precise, final ceiling to flange
alignment.
• Galvanized steel junction box with hinged access covers and spring latch. Three
combination 1/2”-3/4” and two 1/2” knockouts for straight-through conduit
runs. Capacity: 8 (4 in, 4 out) No. 12 AWG conductors rated for 90°C.
Advance Mark 10® electronic dimming ballast.
Minimum dimming level 5%
electronic dimming ballast.
Minimum dimming level 5%
Options
6
ELR
ELRSD
GMF
GLR
CPChicago plenum
BDP
MFLG
SQMT
Emergency battery pack. Remote test switch
6
Emergency battery pack with self-diagnostics. Remote test switch provided
7
Single, slow-blow fuse
7
Single, fast-blow fuse
8
Ballast disconnect plug
9
Microflange trim
10
Square metal trim
ACCESSORIES order as separate catalog numbers (shipped separately)
NSP5 D ER KIT
SQFW-4-LENSED
PAGE 1 OF 4
Sensor Switch nLight secondary relay and dimming pack device used to switch and dim luminaires powered via an emergency circuit. Refer to NSP5 D ER KIT.
GOTHAM ARCHITECTURAL DOWNLIGHTING | 1400 Lester Road Conyers GA 30012 | P 800.315.4982 | gothamlighting.com
Interface for Sensor Switch® nLight® network provided with integral power supply.
Refer to TN-623-01.
RRL__
TRW
TRBL
RELOC®-ready luminaire connectors enable a simple and consistent factory installed
option across all ABL luminaire brands. Refer to RRL for complete nomenclature.
12
White painted flange
13
Black painted flange
4” SQFW
(35.7)
Overlap Trim:5-3/4 (14.6)
Square Lensed Wallwash
Triple-Tube lamp
DIMENSIONAL DATA NOTES
All dimensions are inches (centimeters) unless otherwise noted.
7. Not available with MVOLT. Must specify voltage.
8. Meets codes that require in-fixture disconnect.
9. Order ships as 3 components: housing, trim and microflange gypsum board.
10. Not available with stepped reflector or MFLG option.
11. For emergency generator/inverter applications order non-nLight enabled fixture
and NSP5 D ER KIT as an accessory. Refer to NSP5 D ER KIT.
12. Not available with white reflector.
13. Not available with black reflector.
SQFW-4-LENSED
PAGE 2 OF 4
4” SQFW
room
wall
Plane Angle
s
SQFW 1/26TRT 4A
CF26DT/E/IN/835
1800
Test
SQFW 1/32TRT 4AR
CF32DT/E/IN/835
2400
Test
90°
0
0
0
0
0
0
0
0
0
s
SQFW 1/26TRT 4DSR
CF26DT/E/IN/835
1800
Test
s
Square Lensed Wallwash
Triple-Tube lamp
PHOTOMETRY
TECHNICAL INFORMATION
Footcandle values are initial and tables are based on minimum of six units. For fixture-to-wall
distance other than those shown, use maximum of one-to-one spacing (distance between fixtures not
more than distance to wall) for best results.
Footcandle values are initial and tables are based on minimum of six units. For fixture-to-wall
distance other than those shown, use maximum of one-to-one spacing (distance between fixtures not
more than distance to wall) for best results.