GOSSEN METRAWATT METRISO INTRO Datasheet

Page 1
METRISO INTRO, BASE, TECH
High-Precision Insulation, Low Resistance and Voltage Measurement Instrument
Insulation measurement per EN 61557-2/VDE 0413, part 2
Low-resistance measurement
Intelligent filter: precise and measurement-dependent activation for the measurement of very high resistances
• Digital and analog display, backlit
• Indication of dangerous contact voltage LED
Acoustic signalling when limit value is exceeded
Detection of interference voltage in switch position OFF*
Overvoltage protection Protects the instrument in the event of inadvertent connection to mains power – Fuse link for all resistance measuring ranges – Electronic fuse for the protection of low resistance
and resistance measurement R
• Compact and rugged for service calls under harsh conditions
METRISO INTRO/TECH:
Voltage testing and measurement up to 1000 V
METRISO BASE/TECH: One measuring point self-test with test resistance of 10 M
per IEC/HD 60364-6 / EN 50110
per EN 61557-4/VDE 0413, part 4
and R
LO
3-349-810-03
1/12.14
German Accreditation Body D-K-15080-01-01
Applications
METRISO INTRO/BASE/TECH insulation and resistance measur­ing instruments allow for quick and effective testing of protective measures in accordance with DIN VDE 0100, ÖVE-EN 1 (Austria), NIV/NIN SEV 1000 countries as well. The instruments are equipped with a micropro­cessor and comply with IEC/EN 61557 / VDE 0413 regulations: Part 1: General requirements
Part 2: Insulation resistance measuring instruments Part 4: Instruments for measuring resistance at earthing conduc-
tors, protective conductors and equipotential bonding
Part 10: Combined measuring equipment for testing, measuring
or monitoring protective measures
As well as requirements per VDE 0701-0702: Repair, modification and testing of electrical devices
The insulation measuring instruments are suitable for the following tasks:
• Measurement of insulation resistance at voltage-free devices and systems, up to 1000 V depending upon variant
• Testing of the resistance of earthing conductors, protective conductors and equipotential bonding
• Checking of test objects for absence of voltage
• Testing of electrostatic discharge capacity at floor coverings (using shielded measurement cables) – EN 1081
(Switzerland), and regulations specific to other
Features Overview of Both Instrument Variants
METRISO INTRO BASE TECH Article number M550N M550O M550P Measurements
U = 1000 V
R
INS
R
U = 250, 500 V ✓✓✓
INS
R
U = 50, 100 V ✓✓
INS
R 10 ... 10 k
RLO 0.17 ... 10
U 10 ... 1000 V
U 10 ... 500 V
Display Functions
Backlit display Limit value LED (green/red) for:
Additional acoustic signal, limit value per VDE 0100
LED for dangerous contact voltage
(when switched off) LCD symbol for external voltage
Battery level display
Special Functions
Discharge capacitive devices under test Safety shutdown (UBatt < 8 V)
Features
CAT II 1000 V / CAT II I 600 V / CAT IV 300 V Measuring category CAT III 600 V / CAT IV 300 V 10 M test resistor DAkkS calibration certificate
✓ ✓
R
INS RLORINS RLORINS RLO
✓ ✓
✓ ✓
— —
✓✓ ✓✓
✓✓
✓✓
✓✓
✓✓ ✓✓
✓✓ ✓✓
✓✓ ✓✓ ✓✓
GMC-I Messtechnik GmbH
Page 2
METRISO INTRO, BASE, TECH
100
Ux/V
R
x
/k
U
N
= 100 V
0
20
40
60
80
100
250
Ux/V
Rx/k
U
N
= 250 V
0
50
100
150
200
250
0
100
200
300
400
500
500
U
N
= 500 V
Ux/V
Rx/k
0
200
400
600
800
1000
1
U
N
= 1000 V
Ux/V
Rx/M
High-Precision Insulation, Low Resistance and Voltage Measurement Instrument
Characteristic Values
Meas.
Qty.
RINS
U
AC/
DC
RLO 10 0.17 ... 9.99
R
1)
Display range up to 600 V
2)
Display range up to 1.2 kV
3)
the indicated accuracy is only achieved with the shielded high-resistance measuring cable KS-C (article no. Z541F)“
UiSO Range Measuring Range
100 k 10.0 k ... 99.9 k 0.1 k
1 M 100 k ... 999 k 1 k
10 M 1.00 M ... 9.99 M10 k
BASE/TECH: 50 V
BASE/TECH: 100 V
INTRO: 250 V ... 1000 V
BASE: 250 V / 500 V
METRISO BASE
METRISO INTRO
METRISO TECH
METRISO BASE METRISO TECH
Display range as of 01.0
100 M 10.0 M ... 99.9 M100 k
1 G 100 M ... 999 M 1 M
10 G 1.00 G ... 9.99 G10 M
100 G 10.0 G ... 99.9 G100 M (8% rdg. + 3 d) 3)(10% rdg. + 3 d)
TECH: 250 V / 500 V / 1000 V
200 G 100 G ... 199 G 1 G (25% rdg. + 5 d) 3)
100 V 10.0 V ... 99.9 V 0.1 V 500 V 100 V ... 510 V 100 V 10.0 V ... 99.9 V 0.1 V
1000 V 100 V ... 999 V
100 10.0 ... 99.9 0.1
1 k 100 ... 999 1
10 k 1.00 ... 9.99 k 10
Reso­lution
1)
1 V
2)
1 V
0.01 4 V < U0
Open-Circuit
Voltage U
50 V /100 V:
1.25 U
250 V / 500 V /
1000 V:
1.1 U
(2.5% rdg. + 3 d) (5% rdg. + 3 d)
(2.5% rdg. + 3 d) (5% rdg. + 3 d)
< 6 V
U0 max. 15 V
4)
5)
Te st
Current
0max
ISO
IN = 1 mA
I
5 mA
K
ISO
200 mA I
I  260 mA
1 mA I
I 1,3 mA
does not conform to DIN EN 61557-2 up to 5
Intrinsic Uncertainty
(5% rdg. + 3 d) (7% rdg. + 3 d)
(2.5% rdg. + 3 d) (5% rdg. + 3 d)
(2.5% rdg. + 3 d) (5% rdg. + 3 d)
Measuring
Uncertainty
(50% rdg. + 20 d)
Overload Capacity
METRISO BASE: 600 V AC/DC
METRISO INTRO METRISO TECH:
3)
3) 4)
600 V AC/DC
1000 V AC/DC
METRISO BASE:
600 V AC/DC
METRISO INTRO METRISO TECH:
1000 V AC/DC TRMS
METRISO BASE:
600 V AC/DC
METRISO TECH
1000 V AC/DC TRMS
TRMS
TRMS
TRMS
TRMS
TRMS
TRMS
Voltage at Device Under Test During Insulation Resistance Measurement
Measuring voltage Ux at the device under test depending upon its resistance Rx at nominal voltages of 100, 250, 500 and 1000 V:
Intelligent Filter
Measurement-dependent and precise activation for the measurement of very high resistances with:
• beating, i. e. compensation of 16
• attenuation of capacitive influences from power cables, etc.
• suppression of electric field influences
2 GMC-I Messtechnik GmbH
2
/3Hz and 50 Hz interference
Page 3
METRISO INTRO, BASE, TECH
M Vk
TRMS
AC
DC
Rlo>10%
MAN
DATA
ZERO
G
ISO
2500V
1000V
Tk
1
0
0
k
1
G
1
0
k
1
M
1
0
G
0
1
0
0
0
V
1
2
0
0
G
1
0
0
M
1
0
M
!
High-Precision
Insulation, Low Resistance and Voltage Measurement Instrument
Reference Conditions
Reference temperature + 23 C 3 K
Relative humidity 40 ... 75% Measured quantity
frequency 45 Hz ... 65 Hz Measured quantity
waveshape Sine, deviation between TRMS and recti-
fied value < 1% Battery voltage 9.5 V 0.1 V Test resistor 10 M1%
Electrical Safety
Protection class II Pollution degree 2 Measuring category METRISO INTRO/TECH:
CAT II 1000 V / CAT III 600 V / CAT IV 300 V
METRISO BASE
:
CAT II I 600 V / CAT IV 300 V Fuses Fuse link FF315mA/1000V, effective in all resis-
tance measuring ranges, 1 additional
replacement fuse in the battery compartment Elektronic fuse for protecting low-resistance and resis-
tance measurement R
(not METRISO G500MM (M550K))
and R
LO
Ambient Conditions
Accuracy temperature range 0 ... +40 C
Operating temperature –10 ... +50 C
Storage temp. range –25 ... +70 C (without batteries) Relative humidity Up to 75% (max. 85% during storage/
Elevation Max. 2000 m Calibration interval 1 year (recommended)
transport), no condensation allowed
Displays
Digital Display With additional bar graphs or pointer
depending on selection with a.disp parameter, backlit (transflective); leading zeros can be suppressed at the digital display depending on selection with
0.disp parameter; overranging indicated with 0L at display; dimensions: 65 x 36 mm
Cable resistance
If measurement results for the two direc­tions of current flow (polarity reversal) differ by more than 10% (this corresponds to typical measuring error for the instru­ments), both measured values are dis­played next to each other with reduced resolution.
Limit LED LED lights up red to indicate an exceeded
limit value LED lights up green to indicate adherence to the limit value
LED LED lights up red to indicate:
at LCD Detection of external voltage at the LCD
– the presence of an external voltage
bevore insulation testing
(U > 50 V) with the device switched on or off (device switched off not with M550N)
– the presence of the test/measuring voltage
during (insulation) measurement (U > 50 V) the presence of a residual voltage after insulation testing (U > 50 V) with the device switched on or off
with the device switched on where U DC > 50 V and U AC > 40 V (50 Hz) for all mea­suring functions
Mechanical Design
Electromagnetic Compatibility (EMC)
Interference emission EN 61326-1:2006 class B Interference immunity EN 61326-1:2006
GMC-I Messtechnik GmbH 3
Dimensions 225 x 130 x 140 mm Weight Approx. 1.4 kg with batteries Protection Housing: IP 52, measurement cables and
connectors: IP 40 per DIN VDE 0470, part 1 / EN 60529, housing category 2
Extract from table on the meaning of IP codes
(1
IP XY
st
Protection Against Foreign
digit X)
2 12.5 mm dia. 2 Dripping (at 15° angle) 3 2.5 mm dia. 3 Spraying water 4 1.0 mm dia. 4 Splashing water 5 Dust protected 5 Jet-water 6 Dust-proof 6 Powerful water jets
Object Entry
IP XY
(2nd digit Y)
Protection Against
Penetration by Water
Page 4
METRISO INTRO, BASE, TECH
High-Precision Insulation, Low Resistance and Voltage Measurement Instrument
Power Supply
Batteries 8 ea. 1.5 V mignon cell (8 ea. size AA)
Nominal range of use 8.5 ... 12 V Battery test Battery capacity display with battery sym-
Battery saver circuit Automatic shutdown of display illumination
Service life For R
Safety shutdown If supply voltage is too low, the instrument
(alkaline manganese per IEC LR14)
bol in 4 segments: . Querying of momentary battery voltage via menu function.
after 15 second s (after the last time the rotary switch is actuated) can be set via the blight parameter. The test instrument is automatically switched to the standby mode* when the measured value remains unchanged and none of the controls are activated during this time.
* Specified time “APoFF” (entered in minutes)
adjustable via SETUP menu (default setting approx. 10 min).
(1000 V / 1 M) and RLO with 20
INS
seconds on-time and 1 measurement each for a duration of 5 seconds: – With batteries (alkaline manganese):
900 measurements
– With rechargeable batteries (2200 mAh):
850 measurements
is switched off, or cannot be switched on. When the rotary switch is set to the OFF position, the instrument is completely dis­connected from the batteries (after approximately 10 seconds).
Scope of delivery
1 Insulation and resistance measuring instrument 1 DAkkS calibration certificate (not METRISO INTRO) 1 Set batteries (not METRISO INTRO) 1Carrying strap 1 Alligator clip (not METRISO INTRO) 1 KS17-4 cable set 1 Condensed operating instructions 1 Supplement Safety Information 1 Detailed operating instructions for download from our website
at www.gossenmetrawatt.com
Accessories (not included)
ISO Kalibrator 1
Calibration adapter for the rapid, efficient testing of the accuracy of measur­ing instruments for insula­tion resistanced and low­impedance resistances.
Cable Set KS-C
Cable set consisting of measurement cable and high resistance measuring cable, for measurements in the G- range.
Applicable Regulations and Standards
IEC 61010-1 / EN 61 010-1/ VDE 0411-1
DIN EN 61557 / VDE0413 Part 1:2007-12 General requirements
EN 1081 Testing of electrostatic discharge capacity for floor cover-
EN 60529 VDE 0470, part 1
DIN EN 61326-1 VDE 0843-20-1
Safety requirements for electrical equipment for mea­surement, control and laboratory use – General requirements
Part 2:2008-02 Insulation resistance measuring
instruments
Part 4:2007-12 Instruments for measuring
resistance at earthing conductors, protective conductors and equipotential bonding
Part 10: 2001-12 Combined measuring equipment
for testing, measuring or monitoring protective measures
ings in potentially explosive atmospheres Test instruments and test procedures
Degrees of protection provided by enclosures (IP code) Electrical equipment for measurement, control and labo-
ratory use – EMC requirements – Part 1: General requirements
Cable Set KS24
Cable set KS 24 consists of a 4 m long extension cable with a permanently mounted test probe at one end and a contact pro­tected socket at the oppo­site end, as well as an alli­gator clip for plugging onto the test probe.
4 GMC-I Messtechnik GmbH
Page 5
METRISO INTRO, BASE, TECH
Measurement key
Key for
Measuring point illumination
measuring point illumination
Safety cap
Safety collar
Test pro be
Connection example: module slot for INTRO / BASE / TECH / PRO / XTRA
Movable contact pro­tection securely cov­ers the magnetic con­tact by eleastic force
magnetic strain relief
High-Precision
Insulation, Low Resistance and Voltage Measurement Instrument
Telearm 1
Reel TR25
Test Probe for Remote Triggering Z550A
Floor Probe
The 1081 floor probe can be used for measuring the resistance of insulating floors in accordance with DIN VDE 0100 Part 600 and EN 1081.
The test probe with integrated control module allows for remote triggering in areas with difficult access or in situations which require your full attention. Poorly lit measuring points can be ilumi­nated with the integrated test probe lighting. The connection cable is shielded from interfering influences.
Magnetic measuring contacts (patent) with magnetic strain relief (Z502U)
Drum with Measurement Cable TR50
50m measurement cable coilded around a metal drum. Connection to one end of the cable is accomplished with a jack which is integrated into the drum. The other end is equipped with a banana plug. The drum axle with handle can be removed for space saving storage. Cable resistance component can be compensated for in selector switch position R
LO
.
GMC-I Messtechnik GmbH 5
Page 6
METRISO INTRO, BASE, TECH
High-Precision Insulation, Low Resistance and Voltage Measurement Instrument
Operating Case METRISO G (Z550C)
Order Information
Description Type Article number
Insulation measuring instrument for DIN VDE 0100, ÖVE-EN 1 (Austria) and NIV/NIN SEV 1000 (Switzerland), complies with IEC/EN 61 557/VDE 0413, parts 1, 2, 4 and 10
Test voltages from 50 V to 1000 V, voltage measurement to 1000 V, including low-resistance measure­ment METRISO TECH M550P
METRISO TECH for Remote Triggering (Z550A) and Operating Case (Z550C)
Test voltages from 50 V to 500 V, voltage measurement to 500 V, including low-resistance measure­ment METRISO BASE M550O
METRISO BASE for Remote Triggering (Z550A) and Operating Case (Z550C)
inclusive Test Probe
METRISO TECH-Set M551P
inclusive Test Probe
METRISO BASE-Set M551O
Description Type Article number
Test voltages from 250 V to 1000 V, voltage measurement to 1000 V, including low-resistance measure­ment METRISO INTRO M550N
METRISO INTRO for Remote Triggering (Z550A) and Operating Case (Z550C)
Accessories (not included)
Calibration adapter for testing the accu­racy of instruments used for measuring insulation resistance and low-resistance for test voltages of up to 1000 V (per VDE 0413, parts 1, 2 and 4).
Cable set consisting of measure­ment cable and shielded high-resis­tance measurement cable for mea­surements in the G range KS-C Z541F
Alligator and KS-C
Cable set consisting of a 4 m long extension cable with a permanently attached test probe at one end and a contact protected socket at the other end, and 2 alligator clips which can be plugged onto the test probe KS24 GTZ3201000R0001
Triangular probe for floor measure­ments per EN 1081, DIN VDE 0100­600 (Standing-Surface Insulation) 1081 probe GTZ3196000R0001
Telescoping rod for PE measurement Telearm 1 GTZ3232000R0001 Reel with 25 m measurement cable TR25 reel GTZ3303000R0001 Drum with 50 m measurement cable TR50 drum GTY1040014E34 Test probe with START/STOP key and
an additional key for illuminating the measuring point, including shielded cable and test probe holder for car­rying belt
Magnetic Measuring contacts with contact protection – Set with mag­netic holder, measurement contacts 5,5 mm in diameter insulated, CAT III 1.000 V / 4 A, temperature between –10 °C and 60 °C, under standard conditions and flat-head screws holding force 1.200 g verti­cal to contact area; measuring instrument connector: angled multilam plug according (for METRISO G series)
Operating case for BASE / TECH / PRO / XTRA with outer bag for measuring leads
inclusive Test Probe
clips (1 pair) for KS17-4
METRISO
INTRO /
METRISO INTRO-Set M551N
ISO calibrator 1 M662A
KY-95-3 Z110J
Test Probe for Remote Triggering METRISO G Z550A
Set 1 – Magnetic Mea­suring Tips Z502U
Operating Case METRISO G Z550C
For additional information regarding accessories please refer to
• www.gossenmetrawatt.com
Edited in Germany • Subject to change without notice • PDF version available on the Internet
GMC-I Messtechnik GmbH Südwestpark 15 90449 Nürnberg, Germany
Phone: +49 911 8602-111 Fax: +49 911 8602-777 e-mail: info@gossenmetrawatt.com www.gossenmetrawatt.com
Loading...