GOSSEN METRAWATT METRAport 3A User Manual

Page 1
METRAport3A Folding Analog Multimeter
9 voltage measuring ranges, V : 100 mV, 300 mV, 1 V, 3 V, 10 V, 30 V, 100 V, 300 V and 600 V
7 current measuring ranges, A : 10 µA, 100 µA, 1mA, 10 mA, 100 mA, 1 A and 10 A
5 resistance measuring ranges: 1 ... 2 k/ 10 ... 20 k/ 100 ... 200 kΩ/ 1 k ... 2 M/ 10 k ... 20 M
9 level measuring ranges: -40 dB ... +62 dB
• High input resistance of 10 M for no-load voltage measurement
• Reflective scale in folding lid which can be tilted for easy reading and provides transport protection as well, accuracy class 1.5 =
• Overload protection: 600 V in all functions and range settings
•Automatic battery shutdown when instrument is folded closed
3-349-302-03
1/4.04
300 V CAT III 600 V CAT II IEC/EN 61010-1, second edition
Applications
The multimeter is equipped with an indicator display and an electronic amplifier. It can be used in a wide variety of practical electronics applications, for example in R&D, manufacturing, equipment operation, in the test lab and for service calls, as well as for training and vocational education.
Description
The multimeter has 46 measuring ranges for direct and alternating voltages of up to 600 V, alternating voltage levels from
-40 to +62 dB, direct and alternating current of up to 10 A and
resistances of up to 20 MΩ. It has a constant input resistance of 10 M in all voltage measuring ranges.
The multimeter is calibrated in RMS values for periodic sinusoidal quantities. It makes use of full-wave rectification for the evaluation of the arithmetic mean value.
All measuring ranges can be selected with the central measuring range selector switch. The ranges are laid out in a clear-cut fashion around the selector switch.
The measuring device and the display unit are enclosed in two separate housing components which are connected to each other by means of a hinge which can be snapped into various positions. In this way, the ideal angle for ease of reading can be selected with the instrument in any position.
Several well coordinated safety devices protect the instrument against damage caused by incorrect operation and overloading within the specified overload limit values:
• Oversized precision resistors
• Fuse link in combination with protective rectifier diodes
• Overvoltage arrester / positive temperature coefficient resistors (PTCs)
The instrument can be operated independent of mains current with a commercially available 9 V flat cell battery. Long battery service life is assured thanks to the minimal current consumption of the instrument’s electronic components.
The multimeter’s rugged design provides for outstanding protection where harsh mechanical stressing prevails. When folded together, the instrument is provided with extra mechanical protection for the measuring device, as well as for the display unit. The connector jacks are protected against accidental contact. Suitable measurement cables with 4 mm test probes are included as standard equipment.
Applicable Regulations and Standards
IEC/EN 61010-1:2001 VDE 0411-1:2002
DIN EN 61326 VDE 0843, part 20
DIN EN 60529 DIN VDE 0470, part 1
Safety requirements for electrical equipment for measurement, control and laboratory use
Electrical equipment for control technology and laboratory use – EMC requirements
Test instruments and test procedures – Degrees of protection provided by enclosures (IP code)
GOSSEN METRAWATT GMBH
Page 2
METRAport3A Folding Analog Multimeter
Characteristic Values
2)
Current at
Input
Level
i
Voltage Drop
Value at
Scale
Middle
(R
)
i
1)
Voltage
100 mV -20 dB -40 ... ÷ 1 8 dB
300 mV -10 dB - 30 ... ÷ 8 dB 600 V 1 V 0 dB - 20 ... + 2 dB 600 V 3 V + 10 dB - 10 ... + 12 dB 600 V 10 V +20 dB 0 ... + 22 dB 600 V 30 V +30 dB + 10 ... + 32 dB 600 V 100 V +40 dB + 20 ... + 42 dB 600 V 300 V +50 dB + 30 ... + 52 dB 600 V 600 V +60 dB + 40 ... + 62 dB 600 V
1)
The 100 mV to 10 V measuring ranges can also be used for current measurement in accordance with the following table (e.g. reverse current or insulation current). These measuring ranges are rated at accuracy class 5. Frequency range at
~: 15 ... 100 Hz.
Same overload protection as for voltage measuring ranges.
2)
Measured value = displayed value + constant, 0 dB 0.775 V, i.e. 1 mW at
600
3)
Protected with PTC resistor
Range
100 mV 10 nA 300 mV 30 nA
1 V 100 nA
3 V 300 nA
10 V 1 µA 30 V 3 µA
Current
10 µA 10.0 k 100 mV 600 V
100 µA 1.0 k 100 mV 600 V
1 mA 100.0 100 mV 600 V
10 mA 10.0 100 mV 600 V
100 mA 1.4 140 mV 600 V
1 A 480 m 0.480 V 600 V
1 0 A 26 m 260 mV 600 V
Resistance
Range
x1 1Ω ... 2 k 45.6 100mV 2.2 mA 600 V x10 10Ω ... 20 k Ω 456.0Ω 100mV 0.22mA 600 V x 100 100 Ω... 200 k Ω 4.56 kΩ 100 mV 22 µA 600 V
k x1 1kΩ ... 2 MΩ 45.6 kΩ 1 V 22 µA 600 V k x10 10kΩ... 20 MΩ 456.0kΩ 1 V 2.2 µA 600 V
3)
Protection by means of FF 1.6A/600V AC fuse link in combination with rectifier diodes.
4)
FF 16A/600V fuse link, 10 A: max. 10 minutes
Constant Measuring Span
Upper Range Limit
Resistance R
Reading Range
Accuracy under Reference Conditions per IEC 60051/EN 60 051
Class 1.5 for zero-frequency quantities, class 2.5 for periodic sinusoidal quantities and class 1.5 for resistance (intrinsic error relative to 69 mm scale length) corresponding to max. 10% intrinsic error of the measured value within the range of the exaggerated scale arc.
10 M
U
Input
Resistance
10 M / /
50 pF
R
i
Open-
Circuit
Voltage
U
0
Overload
R
i
Protection
600 V
Overload Protection
to
Short­Circuit
Current
I
K
3)
to
3)
3)
3)
3)
3)
3)
4)
Overload
Protec-
tion
to
Reference Conditions
Ambient temperature + 23° C ± 2 K Relative humidity 40 ... 60% Normal position
of use Instrument and scale horizontal ±1° Measured quantity
frequency 45 ... 65 Hz Measured quantity
waveshape
Si
ne Battery voltage 7.5 V ±0.1 V Other influencing
quantities per IEC 60051/EN 60051
Influencing Quantities and Nominal Ranges of Use
Temperature +5 ... +23 ... + 35° C Limiting temperatures For accuracy +5 ... + 35° C
For operation 0 ... +40° C For storage - 25 ... +65° C (without batteries)
Position Additional influence error of max. ±1% of
the scale length if the scale is tilted between 0 and ±120° relative to horizontal
Frequency Additional influence error of max. ± 5% of
Auxiliary voltage No additional influence error. The upper
Series-mode interference voltage damping For V : > 60 dB, AC 50 Hz
Common-mode interference voltage damping > 120 dB, DC and 50 Hz AC
Other influencing quantities per IEC 60051/EN 60051
3)
Power Supply
3)
Battery operation Nominal voltage: 9 V ,
3)
3)
3)
Battery service life With zinc-carbon: approx. 500 hours, with
Battery test Pointer must be within the battery test
full scale value in the following ranges:
100 mV, 3 V ... 600 V: 15 Hz ... 1 kHz 10 µA ... 10 A: 15 Hz ... 1 kHz 300 mV, 1 V: 15 Hz ... 200 Hz
limit must be set with the potentiometer for all measuring ranges in the case of resistance measurement.
For V
~: > 120 dB, DC
9 V flat cell battery per IEC 6LR61 (6F22), alkaline manganese, zinc-carbon or NiCd rechargeable battery.
alkaline manganese: approx. 1000 hours, with NiCd: approx. 200 hours, in the x 1 range: ¼ of specified service life
field.
2 GOSSEN METRAWATT GMBH
Page 3
METRAport3A
Folding Analog Multimeter
Fuses
Ranges to 1 A and ΩFF 1.6A/600V, 6 mm x 32 mm in
10 A range FF 16A/600V AC, 6 mm x 32 mm,
combination with rectifier diodes for the 10 µA ... 1 A and x1 ... k x10 ranges, switching capacity: 50 kA at 600 V~
switching capacity: 50 kA at 600 V~
Electrical Safety
Safety class II per IEC/EN 61010-1:2001/VDE 0411-
1:2002 Measuring category II III Operating voltage 600 V 300 V Fouling factor Test voltage 3.5 kV~ per IEC/EN 61 010-1:2001/
2
VDE 0411-1:2002
Electromagnetic Compatibility (EMC)
Interference emission EN 61326:2002 class B Interference immunity EN 61326:2002
IEC 61000-4-2:1995/A1:1998,
Feature B
8 kV atmospheric discharge
4 kV contact discharge IEC 61000-4-3:1995/A1:1998, Feature B
3 V/m
Order Information
Description Type Article Number
Folding analog multimeter for demanding requirements METRAport
Consumable Materials
Fuse link (shipped in package of 10) FF(UR)1.6A/700V AC Z109E
Fuse link (shipped in package of 10) FF(UR)16A/600V AC Z109A
Accessories
Carrying pouch F822 GTY 3172 095 P01
Current measuring adapter for safe, trouble-free measurement of current consumption via the mains plug of connected power consumers SM16 GTM 9070190E0002
High-voltage probe, 3 kV/3 V, , also suitable as low pass filter for frequency converter signals HV3 GTZ 3431 001R0011
High-voltage probe, 30 kV / 30 V DC, For safe measure­ment of direct voltage of up to 30 kV HV30 GTZ 3431 001R0001
Temperature probes with integrated or plug-on sensors (see Measuring Instruments and Testers catalog) Z3431... GTZ 3431...
For additional information regarding accessories please see:
Measuring Instruments and Testers catalog
• www.gossenmetrawatt.com
3A M113A
Accessories
SM16 Current Measuring Adapter
Mechanical Design
Protection Housing: IP 40, connector jacks: IP 20 Dimensions 146 x 118 x 44 mm (folded closed) Weight approx. 0.45 kg without battery
HV3 High-Voltage Probe
Standard Equipment
1multimeter 1 9 V battery 1 KS17 measurement cable 1 set operating instructions
HV30 High-Voltage Probe
GOSSEN METRAWATT GMBH 3
Page 4
METRAport3A Folding Analog Multimeter
Current Measuring Accessories Suitable for
All current sensors and transformers are equipped with a connector cable (1.2 to 1.5 m long) with 4 mm safety banana plugs
Type Designation Measuring Range Meas.
Category
Max. Wire Dia.
Transformation Ratio
Frequency Range
Intrinsic Error ±(% rdg. + ...)
Article Number
METRAport
3A
AC/DC Current Sensors with Voltage Output
Z201A Clip-on current sensor
with battery mode (30 h)
Z202A Clip-on current sensor
with 2 measuring ranges,
0.01 ... 20 A~/30 A– 300 V / CAT III
0.1 ... 20 A~/30 A–,
1 ... 200 A~/300 A–
300 V / CAT III
19 mm 100 mV/A DC ... 400 Hz
... 20 kHz
19 mm 10 mV/A,
1 mV/A
DC ... 2 kHz ... 10 kHz
1% + 0.002 A Z201A
1% + 0.03 A, 1% + 0.3 A
Z202A
battery mode (50 h)
Z203A Clip-on current sensor
with 2 measuring ranges, battery mode (50 h)
Z13B Clip-on current sensor
with 2 measuring ranges, battery mode (50 h)
1 ... 200 A~/300 A–, 1 ... 1000 A~/A–
0,2 ... 40 A~/60 A–,
0.5 ... 400 A~/600 A–,
300 V / CAT III
300 V / CAT IV
31 mm 1 mV/A DC ...10 kHz 1% +0.5 A Z203A
50 mm 10 mV/A,
1 mV/A
DC ... 65 Hz ... 10 kHz
1.5% + 0.5 A
2.5%
Z13B
AC Current Sensors with Voltage Output
WZ12B Clip-on current sensor 10 mA~ ... 100 A~ 300 V /
WZ12C Clip-on current sensor
with 2 measuring ranges
WZ11B Clip-on current sensor
Z3512A Clip-on current sensor
with 2 measuring ranges
with 4 measuring ranges
AF033A AmpFLEX flexible current
sensor with 2 measuring ranges, battery (150 h)
AF11A AmpFLEX flexible current
sensor, battery (150 h)
AF33A AmpFLEX flexible current
sensor with 2 measuring ranges, battery (150 h)
AF101A AmpFLEX flexible current
sensor with 2 measuring
1 mA~ ... 15 A~, 1 ... 150 A~
0.5 ... 20 A~,
5 ... 200 A~
1 mA ... 1/10 A~ 100/1000 A~
5 ... 30 A~, 5 ... 300 A~
5 ... 1000 A~ 1000 V /
5 ... 300 A~, 5 ... 3000 A~
5 A~... 1 k A~, 50 A~... 10 k A~
CAT III
300 V / CAT III
600 V / CAT III
600 V / CAT III
1000 V / CAT III
CAT III
1000 V / CAT III
1000 V / CAT III
15 mm 0.1 mV/mA 45 ... 65
15 mm 1 mV/mA,
1 mV/A
20 mm 100 mV/A,
52 mm 1 V/A, 100 mV/A,
Length 600 mm
Length 450 mm
Length 900 mm
Length 1200 mm
10 mV/A
10 mV/A, 1 mV/A
100 mV/A, 10 mV/A
1 mV/A 10 ...100 Hz
10 mV/A, 1 mV/A
1 mV/A,
0.1 mV/A
... 500 Hz
45 ... 65 ... 400 Hz
30 .. .48 ... 65 ... 500 Hz
10 ... 48 ... 65 ... 3 kHz
10 ...100 Hz ... 20 kHz
... 20 kHz
10 ...100 Hz ... 20 kHz
10 ...100 Hz ... 20 kHz
1.5% +0.1 mA Z219B
3% + 0.15 mA,
Z219C
2% + 0.1 A
1 ... 3% Z208B
0.5 ... 3%,
0.2 ... 1%
1% + 0.5 A,
Z225A
Z207A
1% +0.5 A
1% + 2 A Z207D
1% + 0.5 A,
Z207B
1% + 2 A
1% + 2 A, 1% + 10 A
Z207C
ranges, battery (150 h)
AC Current Transformer with Current Output
WZ12A Clip-on current transformer 15 ... 180 A~ 300 V /
WZ12D Clip-on current transformer 30 mA ... 150 A~ 300 V /
CAT III
CAT III
WZ11A Clip-on current transformer 1 ... 200 A~ 600 V /
CAT III
Z3511 Clip-on current transformer 4 ... 500 A~ 600 V /
Z3512 Clip-on current transformer 0.5 ... 1000 A~ 600 V /
CAT III
CAT III
Z3514 Clip-on current transformer 1 ... 2000 A ~ 600 V /
CAT III
Without restriction As of 50 A
15 mm 1 mA/A 45 ... 65
15 mm 1 mA/A 45 ... 65
... 400 Hz
... 500 Hz
20 mm 1 mA/A 48 ... 65
... 400 Hz
30 x 63 mm1 mA/A 48 ... 65
52 mm 1 mA/A 30 .. .48 ...
... 1 kHz
65 ... 5 kHz
64 x 150mm1 mA/A 30 .. .48 ...
65 ... 5 kHz
3% Z219A
2.5% +0.1 mA Z219D
1 ... 3% Z208A
3% +0.4 A GTZ 3511
0.5% ... 0.7% GTZ 3512
000 R0001
000 R0001
0.5% +0.1 A GTZ 3514 000 R0001
WZ11/12 ...
Edited in Germany • Subject to ch ange without notice • PDF version available on the Internet
Phone: +49-(0)-911-8602-0 GOSSEN METRAWATT GMBH Thomas-Mann-Str. 16 - 20 90471 Nürnberg,
Germany
Fax: +49-(0)-911-8602-669
E-mail: info@gossenmetrawatt.com
www.gossenmetrawatt.com
Z201 ... Z203
Z13B
Loading...