Gossen MetraWatt METRAOHM 413 Quick Start Manual
METRAOHM⏐413
Low-Resistance Ohmmeter
• Handy measuring instrument per VDE 0413 part 4 / EN 61557-1 / -4
• Large measuring range from 0.01 to 1999 kΩ
• Measurement cable zero balancing
• Compact and durable
For rugged service calls and laboratory use
• Overvoltage protection
Protects the instrument in the event of inadvertent connection
to mains voltage
• Indication of interference voltage
• IP 65 protection
3-348-810-03
6/7.15
Applications
The METRAOHM 413 is a battery powered instrument for the measurement of low-value resistances in electrical systems.
Large protective conductor, earthing, equipotential bonding and
lightning protection systems can also be tested quickly and safely
with the METRAOHM 413. Resistance is measured between
reference earth (e.g. an equipotential bonding strip) and any
desired points to this end.
A measuring current of 200 mA and automatic functions assure
reliable measuring results.
– Adjustment of shunts in instrumentation applications
– Testing of electrical connections at busbars in open-pit
mining, in industry and in household applications
– Testing of cable resistance, wiring, shunt resistors in printed
circuit boards and thick-film circuits
– Measurement of contact resistance in relays, power
contactors and load interrupters
– Measurement of fuse resistance, as well as cable resistance in
heavy current circuits
– Testing of coil resistance in transformers, coils, small motors
etc.
Description
Easy Operation
Operation is very easy. Measurement cables of almost any length
can be used thanks to the offset balancing function.
Measurement polarity can be reversed, and both measured
values are stored to memory for subsequent comparison.
Resultant deviations in the measuring results (e.g. possible
galvanic voltages) can thus be recognized.
Offset Balancing
Offset balancing compensates for measurement cable resistance.
The offset value is saved to memory and is utilized for all future
measurements until balancing is performed once again. The value
remains in memory, even after the measuring instrument has
been switched off.
A variety of measurement cables with resistances of up to 3.5 Ω
can be used.
Protection Against Operator Error
The METRAOHM 413 is protected against inadvertent connection
to devices under test with fault voltages of up to 500 V by means
of protective devices.
Interference Voltage Warning
Interference voltage is indicated visually with a red LED, and
audibly with an acoustic warning signal. The voltage value is
displayed at the LCD as well, as long as the test probe makes
contact.
GMC-I Messtechnik GmbH
METRAOHM⏐413
Low-Resistance Ohmmeter
Applicable Regulations and Standards
IEC 61010–1
DIN EN 61010–1
VDE 0411 Part 1
EN 61557-1 / -4 /
VDE 0413 Part 4
EN 60529
VDE 0470-1
DIN EN 61326-1
VDE 0843-20-1
Safety requirements for electrical equipment
for measurement, control and laboratory use
Part 1: General requirements
Ohmmeters
Test instruments and test procedures
Protection provided by enclosures (IP code)
Electrical equipment for measurement, control and
laboratory use – EMC requirements –
Part 1: General requirements
Characteristic Values
Measuring ranges 10 Ω (Lo-Ω) Auflösung: 0,01 Ω
Accuracy ±(1.5% rdg. + 4 digits) at 20 °C
Measuring current 10 Ω (Lo-Ω)-range: 200 mA
Open-circuit voltage > 4 V
100, 2000 Ω Auflösung: 0,1 ... 1 Ω
20, 200, 2000 kΩ Auflösung: 0,01 ... 1 kΩ
100 Ω-Bereich: 20 mA
further ranges: 1 μA ... 20 mA
Display
Electrical Safety
Safety class II per IEC 61010-1
Test voltage 3.2 kV
Measuring category CAT II 600 V, CAT III 300 V
Overvoltage
protection reversible by means of semiconductor at
nominal voltages of up to 400 V,
from 400 to 500 V with special fuse
(can only be replaced at the factory)
Electromagnetic Compatibility (EMC)
Interference emission
interference immunity
EN 61326-1:2006 class B
EN 61326-1:2006
Mechanical Design
Housing impact resistant ABS with unbreakable
Protection housing: IP 65
Dimensions 60 x 230 x 40 mm
Weight 180 g (including battery)
display cover
Digital display LCD, 10 mm high, 3½ places,
with background illumination
Overflow indication by 0L
Battery status indicated by 2 segments on the LCD
External voltage
display for voltages as from approx. 15 V:
Alternately, red LED VOLT blinks and
symbol – v – appears on the LCD.
Numerical display of voltage level, in the
case of AC voltage, symbol ~ for AC is
additionally shown.
Between 15 V and 400 V an intermittent
acoustic signal sounds as a warning signal
Ambient Conditions
Reference temp. 20 °C
Storage temperature –10 °C ... +70 °C
Operating temp. –10 °C ... +50 °C
Power Supply
Battery 9 volt block battery per IEC 6 LR 61 AlMn,
automatic shutdown after 20 seconds of
inactivity
Standard Equipment
1 METRAOHM 413 low-resistance ohmmeter
1 plug-in measuring cable
1 9 volt block battery per IEC 6 LR61
1 operating instructions
Battery Saving Circuit
The measuring instrument is switched off automatically if none of
the keys are activated for a period of approximately 20 seconds.
2 GMC-I Messtechnik GmbH
Loading...