Gorilla Playsets 1500CWCF, 1500AWC, 1500AWF, 1500AWCF, 1500AWCR User Manual
...
™
™
playsets
playsets
playsets
playsets
™
™
Mountaineer Clubhouse Treehouse
Timber Shield Post Option
BOXES: W-1, 120
*51-0054-W*
51-0054-W
Model: 1500CWCF
[BOXES: 1501, 1503N, 1512,
1530, 1518, 1525, Extreme Tube
Slide Box and Slide Box]
Copyright © 2016 Gorilla Playsets
All Rights Reserved
190 Etowah Industrial Court
Canton, GA 30114
www.gorillaplaysets.com
Amber Post Option
BOXES: 1520-2bx, 1522
***IMPORTANT NOTICE FOR TREEHOUSE KIT PLAYSETS***
Read all instructions thoroughly before beginning construction, this is very important. The
“Treehouse Add On Kit” (1525) box will require you to deviate slightly from the standard kit
instructions.
Typical deviations include:
1) The Telescope that is usually on the front of the set on the Front face board (arched board)
must be moved to another location on the set. Additional instructions to mount the Telescope to
a 2 x 4 or a 4 x 4 are included in the play set Appendix or with the “Treehouse Add On Kit”
manual. Mount the Telescope along the top of any of the railings that do not interfere with any
areas that are activity openings.
2) The Roof Peak Support Triangle will need to be removed from the inside of the Roof Supports
located on the front of the play set. The Plastic Sunburst should be left off the front of the play
set. The “Treehouse Add On Kit” will be added to the front of the play set.
3) Flag Kits which normally reside on the front of the front corner posts at the top should be
relocated to the front slats on the “Treehouse Add On Kit”
Wood/Accessory and Hardware Lists:
These lists for the “Treehouse Add On Kit” are in the Appendix at the end of your play set
instruction manual or they are included with this sheet.
Steps to complete the “Treehouse Add On Kit”:
The instruction steps for the “Treehouse Add On Kit” are in the Appendix at the end of your play
set instruction manual or they are included with this sheet.
If you are adding the “Treehouse Add On Kit” to a playset that is already built:
It will be necessary to remove the Flags and Plastic Sunburst from the front side of your playset
wood roof. Then remove the 5/4 x 10” Roof Peak Support triangle from the inside of the front Roof
Supports. Keep these pieces and hardware since most will be reused during the construction
process.
Fill in the holes in the corner posts from the Flags with clear silicone (not included). If you wish to
fill the holes with a fastener then use #8 x 1” countersunk head screws with silicone in each hole.
You will need to purchase these screws at your local home center if you choose this option.
Fill any small holes in the Roof Supports leftover from removing the Plastic Sunburst with wood
filler. Use a stainable wood filler suitable for outdoor use. Then stain the wood filled spots with a
suitable matching color of stain.
Please inspect and inventory all parts immediately upon accepting delivery. Use the
inventory pages in the manual to make sure you have received all necessary parts.
The quickest method to get any parts that are missing or damaged is to use our “Quick
Response Center” located at:
www.gorillaplaysets.com/support
DO NOT RETURN THIS PRODUCT TO THE RETAILER OR CONTACT THE RETAILER DIRECTLY.
THE RETAILER DOES NOT STOCK COMPONENTS.
PLEASE RETAIN ALL INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE
PLACE WHERE YOU CAN REFER TO THEM AS NEEDED. CHECK FOR REVISED INSTRUCTIONS AT:
www.gorillaplaysets.com/manuals
GORILLA PLAYSETS WARRANTY – 2016
Gorilla Playsets® (“Gorilla”) warrants its play sets to be free from defects in workmanship and materials, under
normal use and conditions, for 10 years for above ground structural wood components and for one year for all
other components (e.g., swings, hardware, plastics, tarps, rope ladder, etc.).
Gorilla warrants all remaining products, including but not limited to its , Free Standing Swing Set, Free Standing
Tire Swing, See-Saw, Children’s Picnic Table with Umbrella, Play-Zee-Bo™, Cedar Toy Chest and spring riders to be
free from defects in workmanship and materials, under normal use and conditions, for a period of 1 year.
Cosmetic imperfections and natural tendencies of wood such as peeling, splintering, warping, seasonal checking
or cracking, knots or knot holes, etc. are normal characteristics of all outdoor wooden play equipment and are
not covered by this warranty. Checks or cracks in wood components that do not affect the intended function of
the part, piece or overall swing set are not covered under this warranty.
Wood rot or decay that develops because the product was installed in an area with poor drainage is not covered
under this warranty. Lumber that has been damaged by wood boring bees, or conditions that develop as a result of
faulty or improper installation of the product, are not covered by this warranty. Fading of stain, discoloration or
mold on any wood part or accessory is not covered by this warranty. Cracks in plastic components, surface rust on
hardware and chips on powder coated materials are not considered defects in material as long as they do not
affect the functionality or structural integrity of the part or component.
It is the owner’s responsibility to maintain the swing set. This includes but is not limited to staining and sealing
the lumber as needed and regular inspection to be sure all hardware is tight. Instructions for proper
maintenance can be found on Gorilla’s website. Imperfections or conditions that develop because of a failure to
properly maintain the swing set are not covered by this warranty.
Gorilla will, at its discretion, replace any above ground part within the stated warranty period that is defective in
workmanship or materials. This decision is subject to verification of the defect, which, at Gorilla’s discretion, may
be accomplished by submitting photographs or by delivery of the defective part to Gorilla Playsets • 190 Etowah
Industrial Ct. • Canton, GA 30114 • 1-800-882-0272 Monday to Friday 9AM-5PM EST. Any warranty claim must
include proof of purchase, including the date of purchase. In addition, within the first 30 days from the date of
purchase, Gorilla will replace any parts discovered to be missing from or damaged in the original packaging.
This warranty is valid only if the product is used for the purpose for which it was designed and installed at a
residential, single-family dwelling. This warranty is void if the product is used in a commercial, institutional or
multi-family setting. This warranty does not cover normal wear and tear or (a) products that have been damaged
by acts of God and/or nature, negligence, misuse or accident; (b) products that have been modified or repaired
by unauthorized persons; (c) the cost of labor; or (d) the cost of shipping any replacement product or part.
GORILLA DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES OF ANY KIND, EXPRESSED, IMPLIED,
STATUTORY OR OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. GORILLA WILL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. This
warranty is non-transferable and does not extend to the owners of the product subsequent to the original
purchaser. Some states do not allow limitations on implied warranties or exclusion of incidental or consequential
damages, so these restrictions may not be applicable to you. This warranty gives you specific legal rights. You may
also have other rights which vary from state to state.
IMPORTANT SAFETY GUIDELINES
This product is recommended for use by children ages 3-11. This product is intended
for residential use only and not intended for use in any public setting. A safety surface
such as mulch or recycled tire should be used under the play set to prevent injury from
falls. Also a 6 foot safety zone should be used around the entire play set.
As with any home project, good judgment and respect for power tools will greatly
reduce the risk of injury. Gorilla recommends you follow all tool manufacturers’ safety
guidelines. Always wear eye protection and safety gloves to prevent injury. In several
phases of construction two people may be required for lifting and securing of lumber.
While the play set is being constructed, please keep children off the equipment until the
project is complete. Bolts and screw heads should be checked regularly for tightness.
The ground ladder, rope ladder, slide, swings and other areas where children spend a
majority of their playtime should be checked more frequently.
Gorilla shall not be liable for incidental, indirect or consequential damages or
injuries that result from building and/or playing on our play sets. Adult supervision is
recommended anytime a play set is being used.
WEIGHT LIMITS FOR GORILLA PLAYSETS
• FORT PLATFORMS: 800 LBS. TOTAL WEIGHT
• SWING BELT: 225 LBS.
• TANDEM SWINGS: 70 LBS. PER CHILD. UP TO 140 LBS. TOTAL WEIGHT.
• TRAPEZE: 125 LBS.
• FULL BUCKET SWING/ HALF BUCKET SWING: 50 LBS.
• HEAVY DUTY TODDLER BUCKET SWING: 85 LBS.
• INFANT SWING: 35 LBS.
• TIRE SWING: 125 LBS. TOTAL WEIGHT
• ROPE LADDER: 75 LBS.
• ROCK WALL: 150 LBS.
• CLIMBING RAMP: 150 LBS.
• MONKEY BARS: 175 LBS.
• ALL SLIDES: 150 LBS.
Gorilla recommends that the weight limits for all components must not be exceeded.
Failure to adhere to these and other safety guidelines could result in damage to the play
set and injury to the users.
THIS PAGE INTENTIONALLY LEFT BLANK
Warranty registration
- Mountaineer Clubhouse treehouse -
Gorilla Playsets™ manufactures
the nest quality products that
are designed for outstanding
strength and durability. We back
our products with an unparalleled
warranty. In the unlikely event
that you will need to contact us
about covered repairs, we must
have a valid Warranty Registration
on le.
option 1
option 2
option 3
3 Easy Ways To REgisTER
Mail this completed form to:
Fax this completed form to:
(800) 880-3300
Complete the online registration form at:
http://www.gorillaplaysets.com/register
Scan this QR Code with your
smartphone to complete the
form using your phone:
OR
Gorilla Playsets
190 Etowah Industrial Court
Canton, GA 30114
Where did you buy this product?
Date of Purchase Store Store City Store State
Your registration information:
Name: _______________________________________________________ Email: ______________________________________
Address: __________________________________________________________________________________________________
Street City State Zip
Please select
your age
How old are
your children?
Would you recommend this product to friends & family?
Comments: ________________________________________________________________________________________________
____________________________________________________________________________________________________________
18-30
31-40
2-3
4-5
41-50
51+
6-7
8+
How would
you rate the
quality of this
product?
Yes
No
Below Average
Poor
Average
Excellent
Above Average
____________________________________________________________________________________________________________
____________________________________________________________________________________________________________
THIS PAGE INTENTIONALLY LEFT BLANK
IMPORTANT – PLEASE READ
underneath the play set
Congratulations! You have just purchase one of the finest residential wooden swing sets available today. As
with any wooden product that spends its entire life outside, in varying elements, it is important to know what to
expect with your new swing set so that your family can enjoy it for many years.
As your swing set acclimates to its new environment, natural characteristics of the wood can show in the form
of checks, or “cracks” in the lumber. In almost all cases this is normal and it will not affect the structural
integrity of your play set and is not covered under warranty.
KEEPING YOUR PLAYSET LIKE NEW
MUST DO’s
The following owner responsibilities are crucial to the safety, integrity and aesthetic appeal of your
swing set and may affect the warranty if not adhered to.
WITHIN 60 DAYS
Check and tighten Hex Bolts/T-nuts, Carriage Bolts/Lock-nuts, and Lag Screws within the first 60 days and
•
then twice annually – once before each season and then once during the season.
WITHIN 90 DAYS
• Apply a sealant or semi-transparent stain with sealant within the first 90 days of owning the swing set. Our
own Stain/sealant is available online here: http://www.gorillaplaysets.com/Playground-Sealant-p/10-0003.htm
Oil based stain or water based stain may be used. Should you choose to use other stain we suggest asking
the product covering specialists at any number of specialty paint stores or home improvement centers for a
product that would work best for your local environment. ** TIP – while the set is new, take a small board from
to the store with you so they can color match the tint of the stain or sealant.
SEASONAL REMINDERS
If your area experiences regular snowfall, remove your fabric tarp/canopy to avoid stretching, sagging or
•
tearing of the material. Store it inside, folded up, and it will be as good as new when winter is over.
If your area experiences extremely cold temperatures, remove swing belts and other pliable features to
•
prolong the lifespan of these play activities.
OTHER TIPS
Spray swing hangers with Pam, Mazola or olive oil to stop squeaking; do not use petroleum based products
•
such as WD-40 or motor oil.
To repel yellow jackets and wasps, use a cotton ball and dab interior wooden corners
•
deck with a liquid dish soap. Avoid using insecticides.
To speed up the slide wipe the center of slide with wax paper every 2 - 3 weeks.
•
For additional safety and maintenance guidelines, please visit our website.
IMPORTANT DOCUMENTS
CUSTOMER MUST READ AND RETAIN
Please go to the following links and read important SAFETY information prior
to using your new play structure.
http://www.gorillaplaysets.com/Swing-Set-Safety-s/85.htm
https://www.gorillaplaysets.com/Maintenance-s/129.htm
http://www.gorillaplaysets.com/manuals.html (Click on your specific model)
http://www.gorillaplaysets.com/Warranty-s/82.htm
NOTE: Your children’s safety is our #1 concern. Observing the following statements
and warnings reduces the likelihood of serious injury. Please review these safety rules
regularly with your children.
WARNING:
Children must NOT use this play set until it has been
completely assembled and inspected by an adult to
ensure it has been properly installed.
Gorilla Playsets
190 Etowah Industrial Court
Canton, GA. 30114
FRONT VIEW
REAR VIEW
1518 Clubhouse Walls
FOR MODELS:
(1500CWC/1500CWCF/1500CWCR/1500CTC)
!!READ ME FIRST!!
The Clubhouse Walls for this unit will require removal of some boards to install the walls.
There will be some boards that will be leftover after the walls are installed.
Have you assembled your play set?
If “yes”, then READ the Leftover Parts notes at the bottom of this page, then turn the page
and proceed.
If “no”, then keep reading below.
If you have NOT already assembled your play set then you will need to do the following as
you are building your play set:
1) DO install the angle supports in Step 6B of the main instruction manual. These will
help stabilize the structure as construction progresses to the end.
2) DO NOT install the Safety Board in Step 33 (Side to Side Roof), Step 42 (Front to Back
Roof) or Step 31 (Tarp Roof) of the main instruction manual.
3) DO NOT install the Sandbox Seats in Step 47 (Side to Side Roof), Step 55 (Front to Back
Roof) or Step 44 (Tarp Roof) of the main instruction manual.
4) DO install the Clubhouse Walls after the entire play set structure is completed.
5) DO NOT build the picnic table until after the clubhouse walls are installed.
The 1500 play set series is modular. Because of this some parts will be leftover after the
Clubhouse Walls are installed.
Leftover Parts:
2 – 5/4 x 6 x 22” Sandbox Seats, 1 – 2 x 6 x 70” Sandbox Board,
All boards for the Picnic Table. The picnic table parts will be part of the leftover pieces for
this set. If your play set is already completed you may choose to remove the picnic table
from the right side of the unit and place it on the left side after the clubhouse walls are
installed. Placing the picnic table in this position will take up approximately 35% of the
useable floor space at the bottom of the play set.
*Clear Silicone Caulk will be needed to fill in any screw holes in the green posts.
#8 X 1-1/4"
WOOD SCREW
QTY: 58
#8 X 1-3/4"
WOOD SCREW
QTY: 118
#8 X 2"
WOOD SCREW
QTY: 28
11-0054
1518 HARDWARE
PAGE 1 OF 1
REV C: 3/24/2014 JH.
9
8
7
6
5/16 x 3-1/2"
LAG SCREW
QTY: 12
3/8" x 1-1/8"
BLACK PLASTIC
PLUG
QTY: 2
5
#2 SQUARE
DRIVE TIP
QTY:1
4
3
5/16" TEE NUT
QTY: 2
2
5/16" WASHER
5/16 X 4-1/2"
HEX BOLT
QTY: 4
QTY: 16
USE THE RULER TO THE RIGHT TO MEASURE YOUR BOLTS AND SCREWS. PICTURE VIEWS SHOWN
ABOVE ARE 1:1 SCALE AND CAN BE USED TO MATCH BOLT AND SCREW SIZES.
1
DESCRIPTIONPICTURE QTY.
5/4 X 6 X 28-1/4"
PANEL SLAT
7
125-6-2825-PS
1 X 3 X 18"
WINDOW TOP
BOARD
1-3-1800-WTB
1 X 3 X 29-7/8"
OPEN WINDOW
OUTSIDE SUPPORT
1
1
1-3-2988-OWOS
1 X 3 X 34-3/4"
WINDOW
BOTTOM BOARD
1-3-3475-WBB
1 X 3 X 40-1/2"
PANEL BOARD
BRACE
1-3-4050-PBB
1 X 4 X 9"
TOP BOARD
WINDOW
1
2
1-4-0900-TBW
1 X 4 X 9-31/32"
OPEN WINDOW
TOP BOARD 3
1-4-0998-OWTB3
3
2
DESCRIPTIONPICTURE QTY.
1 X 4 X 27-3/4"
BOTTOM
WINDOW BOARD
1-4-2775-BWB
1 X 4 X 29-1/2"
OPEN WINDOW
BOARD
1-4-2950-OWB
1 X 4 X 51"
WALL BOARD
5
1
6
1-4-5100-WB
1 X 6 X 8-7/16"
TOP BOARD
1-6-0843-TBD2
1 X 6 X 10-3/16"
TOP BOARD
DOOR 1
1-6-1020-TBD1
1 X 6 X 11-3/16"
OPEN WINDOW
TOP BOARD 2
1-6-1118-OWTB2
2 DOOR 2
2
2
1 X 6 X 13-5/8"
OPEN WINDOW
TOP BOARD 1
1-6-1360-OWTB1
2
DESCRIPTIONPICTURE QTY.
1 X 6 X 27"
ARCH TOP
BOARD DOOR
1-6-2700-ATBD
1 X 6 X 27-3/4"
BOTTOM BOARD
OPEN WINDOW
1-6-2775-BBOW
1 X 6 X 34"
TOP BOARD
1
4
1WINDOW
1-6-3400-TBW
1 X 6 X 51"
WALL BOARD
1-6-5100-WB
2 X 4 X 47-1/2"
TOP PANEL
BOARD
2-4-4750-TPB
2 X 4 X 70"
BOTTOM WALL
BOARD
11
1
2
2-4-7000-BWB
2 X 6 X 70"
BOTTOM PANEL
BOARD DOOR
2-6-7000-BPBD
1
PICTURE DESCRIPTION QTY.
2 X 6 X 47-1/2"
BOTTOM
BOARD TUBE
SLIDE
2-6-4750-BBTS
WINDOW
1
1
07-0013
(NOT SHOWN)
1518
HARDWARE
11-0054
1
STEP 1: REMOVING THE PICNIC TABLE
1: REMOVE THE PICNIC TABLE TO ATTACH THE RIGHT SIDE CLUBHOUSE WALL.
2: REMOVE THE SCREWS THAT CONNECT THE PICNIC TABLE SUPPORTS TO THE CORNER POSTS.
3: SET THE PICNIC TABLE ASSEMBLY AND SCREWS ASIDE IN CASE YOU WISH TO REINSTALL THE
PICNIC TABLE ON THE OTHER SIDE OF THE FORT LATER.
4: PLACE CLEAR SILICONE IN THE SCREW HOLES IN THE CORNER POSTS.
PICNIC TABLE
STEP 2: REMOVING SANDBOX SEATS
1: REMOVE THE TWO SANDBOX SEAT BOARDS TO ATTACH THE WALL BOARDS.
SANDBOX SEAT
STEP 3: REMOVING THE ANGLE SUPPORTS
1: REMOVE THE BACK AND SIDE ANGLE SUPPORTS UNDER THE DECK.
2: KEEP THE TWO ANGLE SUPPORTS AT THE FRONT.
3: AFTER YOU INSTALL ALL THE CLUBHOUSE WALLS PUT THE ANGLE SUPPORTS BACK ON. IT IS A
GOOD IDEA TO LEAVE SCREWS IN THE ANGLE SUPPORTS AND TO NUMBER THEM AND THEIR
LOCATION FOR LATER.
4: PLACE CLEAR SILICONE IN THE SCREW HOLES IN THE CORNER POSTS FOR THE ANGLE
SUPPORTS AT THE LEFT AND RIGHT SIDES OF THE SET.
ANGLE SUPPORT
STEP 4: TUBE SLIDE BOARD
1: REMOVE THE END PANEL BOARD.
2 X 6 X 21"
END PANEL BOARD
2: PLACE THE BOTTOM BOARD TUDE SLIDE ON THE PLACE END PANEL BOARD . USE 5/16 X 4-1/2" HEX BOLTS, 5/16 X
3-1/2" LAG SCREWS AND FOUR 5/16" WASHERS TO ATTACH IT TO THE CORNER POSTS.
5/16 X 3-1/2"
LAG SCREW
5/16" WASHER
A
5/16 X 4-1/2"
HEX BOLT
2 X 6 X 47-1/2"
BOTTOM BOARD TUBE SLIDE
STEP 5: SAFETY BOARD
1: REMOVE THE SAFETY BOARD.
SAFETY BOARD
2: PLACE THE SAFETY BOARD YOU JUST REMOVED FLUSH WITH 2 X 6 BOTTOM BOARD. USE TWO 5/16 X 3-1/2"
LAG SCREWS AND TWO 5/16" WASHERS TO ATTACH IT TO CORNER POSTS.
3: DAB SOME SILICONE ON THE PLASTIC PLUGS AND PLACE THE PLASTIC PLUGS IN THE HOLES LEFT FROM
REMOVING THE SAFETY BOARD IN THE CORNER POSTS.
2 X 6 X 47-1/2" BOTTOM BOARD
SAFETY BOARD
5/16" WASHER
5/16 X 3-1/2"
LAG SCREW
PLASTIC
PLUG
A
STEP 6: BACK SANDBOX BOARD AND BOTTOM BOARD
1: REMOVE THE SANDBOX BOARD ON THE BACK OF THE FORT .
2 X 6 X 70"
SANDBOX BOARD
2: REPLACE SANDBOX BOARD YOU JUST REMOVED WITH 2 X 6 X 70" BOTTOM PANEL BOARD DOOR WITH CUT
NOTCH UP. USE 5/16 X 4-1/2" HEX BOLTS ON THE TOP HOLES, 5/16 X 3-1/2" LAG SCREWS ON BOTTOM HOLES AND
5/16" WASHERS TO ATTACH IT TO THE POSTS.
3: PLACE THE 2 X 4 X 70" BOTTOM WALL BOARD FLUSH WITH 2 X 6 BOTTOM BOARD. USE TWO 5/16 X 3-1/2" LAG
SCREWS WITH 5/16" WASHERS TO ATTACH IT TO THE POSTS.
2 X 6 X 70"
BOTTOM
BOARD
2 X 4 X 70"
BOTTOM
WALL BOARD
2 X 6 X 70"
BOTTOM PANEL
BOARD DOOR
5/16"
WASHER
5/16 X 3-1/2"
LAG SCREW
5/16 X 4-1/2"
HEX BOLT
5/16 X 3-1/2"
LAG SCREW
5/16" WASHER
STEP 7: TOP PANEL BOARD
1: PLACE THE 2 X 4 X 47-1/2" TOP PANEL BOARD ON THE TUBE SLIDE SIDE OF THE FORT. MAKE THE
TOP PANEL BOARD FLUSH WITH 2 X 6 X 47-1/2" BOTTOM BOARD TUBE SLIDE.
2: USE 5/16 X 3-1/2" LAG SCREWS AND 5/16" WASHERS TO ATTACH THE TOP PANEL BOARD TO
THE CORNER POSTS.
2 X 6 X 47-1/2"
2 X 4 X 47-1/2"
TOP PANEL BOARD
(OFFSET DOWN)
BOTTOM BOARD
TUBE SLIDE
5/16" WASHER
5/16 X 3-1/2"
LAG SCREW
STEP 8: WALL BOARD SWING BEAM SIDE
1: FIND SIX 1 X 6 X 51" WALL BOARDS AND TWO 1 X 4 X 51" WALL BOARDS WITH PRE-DRILLED
HOLES.
2: PLACE WALL BOARDS ON THE SWING BEAM SIDE OF THE FORT AGAINST THE TOP SAFETY
BOARD AND SANDBOX BOARD AS SHOWN BELOW. THE BOTTOM OF THE WALL BOARDS
SHOULD BE 1-1/2 " ABOVE THE BOTTOM OF THE SANDBOX BOARD.
3: USE #8 X 1-3/4" WOOD SCREWS LEAVING 1/4" SPACES BETWEEN THE WALL BOARDS TO
ATTACH THEM TO THE SAFETY BOARD AND SANDBOX BOARD.
#8 X 1-3/4"
WOOD SCREW
1
1
"
2
1 X 4 X 51"
WALL BOARD
(TWO BOARDS)
2 X 4 X 47-1/2"
SAFETY BOARD
1 X 6 X 51"
WALL BOARD
(SIX BOARDS)
STEP 9: ATTACHING PANEL BOARD BRACE
1: PLACE THE 1 X 3 X 40-1/2" PANEL BOARD BRACE AT THE CENTER OF THE WALL BOARDS YOU
ATTACHED TO THE SWING BEAM SIDE. FASTEN IT TO THE WALL BOARDS WITH # 8 X 1-1/4" WOOD
SCREWS.
1 X 3 X 40-1/2"
PANEL BOARD
BRACE
#8 X 1-1/4"
WOOD SCREW
STEP 10: REAR WALL BOARDS
1: PLACE WALL BOARDS ON THE REAR SIDE OF THE FORT AGAINST THE BOTTOM PANEL BOARD
DOOR AND BOTTOM PANEL BOARD AS SHOWN BELOW. THE BOTTOM OF THE WALL PANEL
BOARDS SHOULD BE 1-1/2 " ABOVE THE BOTTOM OF THE BOTTOM PANEL BOARD DOOR . THE
OPENING DIMENSIONS FOR ATTACHING THE WINDOWS IN NEXT STEP ARE SHOWN BELOW.
2: USE #8 X 1-3/4" WOOD SCREWS LEAVING 1/4" SPACES BETWEEN THE WALL BOARDS TO
ATTACH THEM TO THE BOTTOM PANEL BOARD DOOR AND BOTTOM PANEL BOARD.
#8 X 1-3/4"
WOOD SCREW
1 X 6 X 8-3/8"
TOP BOARD
DOOR2
(TWO BOARDS)
1 X 4 X 9"
TOP BOARD
WINDOW
(THREE BOARDS
1 X 6 X 10"
TOP
BOARD
DOOR 1
(TWO
BOARD)
1
1
"
2
112"
14
1
1 X 4 X 51"
WALL BOARD
(FOUR BOARDS)
2 X 4 X 70"
BOTTOM PANEL BOARD
1
"
2
1 X 6 X 51"
WALL BOARD
(THREE BOARDS)
1 X 4 X 27-3/4"
BOTTOM
WINDOW
BOARD
(THREE BOARDS)
STEP 11: INSTALL WINDOW
1: FIND THE PLASTIC WINDOW. PLACE WINDOW AT THE REAR OF THE FORT IN THE OPENING.
THE 1" WIDE SECTION OF THE WINDOW FRAME SHOULD BE AT THE TOP. ATTACH THE WINDOW
WITH FOUR 1-1/4" WOOD SCREWS.
1"
WIDE SECTION
AT THE TOP.
STEP 12: WINDOW BOARD AND DOOR BOARD
1: PLACE THE 1 X 3 X 34-3/4" BOTTOM BOARD WINDOW FLUSH WITH BOTTOM OF THE WINDOW.
FASTEN WITH # 8 X 1-1/4" WOOD SCREWS.
2: PLACE THE 1 X 3 X 18" TOP BOARD WINDOW FLUSH WITH TOP OF THE WINDOW. FASTEN WITH
# 8 X 1-1/4" WOOD SCREWS.
3: PLACE THE 1 X 6 X 27" ARCH TOP BOARD DOOR FLUSH WITH THE BOTTOM OF THE TOP DOOR
BOARD 2 AND TOP DOOR BOARD . FASTEN WITH # 8 X 1-1/4" WOOD SCREWS.
1 X 3 X 18"
WINDOW TOP BOARD
1 X 6 X 27"
ARCH TOP BOARD DOOR
FLUSH
#8 X 1-1/4"
WOOD SCREW
1 X 3 X 34-3/4"
WINDOW BOTTOM BOARD
STEP 13: RIGHT SIDE WALL BOARDS
1: PLACE WALL BOARDS ON THE RIGHT SIDE OF THE FORT AGAINST THE TOP WALL PANEL
BOARD AND ROPE LADDER RUNNER AS SHOWN BELOW. THE BOTTOM OF THE WALL BOARDS
SHOULD BE 1-1/2 " ABOVE THE BOTTOM OF THE ROPE LADDER RUNNER . FASTEN WITH # 8 X 13/4" WOOD SCREWS LEAVING A 1/4" SPACE BETWEEN THE BOARDS.
NOTE: SWING BEAM WALL AND TUBE SLIDE REMOVED FOR CLARITY.
1 x 4 x 10"
OPEN WINDOW
TOP BOARD 3
1 x 6 x 13-5/8"
OPEN WINDOW
TOP BOARD 1
(TWO BOARDS)
(TWO BOARDS)
1 x 6 x 11-1/8"
OPEN WINDOW
TOP BOARD 2
(TWO BOARDS)
#8 x 1-3/4"
WOOD SCREW
1
1
"
2
1 X 6 X 27-3/4"
BOTTOM BOARD
OPEN WINDOW
(FOUR BOARDS)
2 X 4 X 47-1/2"
TOP PANEL BOARD
1 X 6 X 51"
WALL BOARD
(TWO BOARDS)
1 X 4 X 27-3/4"
BOTTOM WINDOW
BOARD
(TWO BOARDS)
2 X 6 X 79-1/2"
ROPE LADDER RUNNER
Loading...