PARTS LIST
QTY
PART DESCRIPTION
10 3/8” X 1 1/4” HEX BOLT
10 3/8” LOCK WASHER
4 3/8” HEX NUT
4 3/8” FLAT WASHER
QTY PART DESCRIPTION
2 3293 SIDE PLATE
1 ST3293 3” X 38 1/4” BOTTOM STEP TUBE
1 CP3293 38 1/4” CENTER PLATE
1
TT3293 2” X 38 1/4” TOP TUBE
ASSEMBLY INSTRUCTIONS
NOTE: READ THE ASSEMBLY AND INSTALLATION INSTRUCTIONS COMPLETELY BEFORE YOU BEGIN.
THIS INSTALLATION REQUIRES CUTTING THE LOWER BUMPER V ALANCE ON MODELS WITHOUT FACTORY
TOW HOOKS.
STEP 1. BEGIN THE GRILLE GUARD ASSEMBLY BY LAYING THE COMPONENT S OUT ON A PROTECTIVE SURFACE.
STEP 2. POSITION THE GRILLE GUARD SIDE PLATES WITH THE FRONT EDGE DOWN AND THE TOP AND BOTTOM
STEP TUBE BETWEEN THE SIDE PLATES.
STEP 3. ATTACH THE TOP AND BOTTOM STEP TUBE TO THE SIDE PLATES USING THE 3/8” X 1 1/4” HEX BOLTS AND
LOCK WASHERS. DO NOT TIGHTEN.
STEP 4. POSITION THE CENTER PLATE BETWEEN THE GRILLE GUARD SIDE PLATES, WITH THE SLOTTED
MOUNTING HOLES IN THE CENTER PLATE DOWN.
STEP 5. INSERT THE 3/8” X 1 ¼” HEX BOLTS THROUGH THE HOLES IN THE SIDE PLATES AND CENTER PLATE, AND
INSTALL THE 3/8” FLAT WASHERS, LOCK WASHER AND HEX NUTS. DO NOT TIGHTEN.
STEP 6. ALIGN THE GRILLE GUARD, AND TIGHTEN ALL NUTS AND BOLTS.
3000 SERIES STEPGUARD
GRILLE GUARD ASSEMBLY INSTRUCTIONS
PART NO. 3293B & 3293C 2009 FORD F-150 2/4WD
Do not attempt to install this product on any vehicle other than the one it is designed for and listed above!
3/8” X 1 ¼” HEX BOLTS & LOCK WASHERS
3/8” HEX NUTS, LOCK WASHERS & FLAT WASHERS
3/8” X 1 ¼” HEX BOLTS
SIDE PLATE
TOP TUBE
CENTER PLATE
STEP TUBE
.
PARTS LIST
QTY
PART DESCRIPTION
1 DRIVER SIDE AUXILIARY UPPER BRACKET
1 DRIVER SIDE LOWER BRACKET
1 DRIVER SIDE UPPER BRACKET
1 PASSENGER SIDE LOWER BRACKET
1 PASSENGER SIDE UPPER AUXILIARY BRACKET
1 PASSENGER SIDE UPPER BRACKET
2 VINYL GASKET
1 WIRE GUIDE
2 M8-1.25 x 40M HEX HEAD BOLT
2 5/16" FLAT WASHER
8 1/2" FLAT WASHER
4 1/2" HEX NUT
QTY
PART DESCRIPTION
4 1/2" LOCK NUT
4 1/2" LOCK WASHER
4 1/2" TAB BOLT
4 1/2 x 1 1/4" CARRIAGE BOLT
6 3/8" FLAT WASHER
2 3/8" HEX NUT
4
3
/8" L
OCK NUT
2 3/8" LO
CK WASHER
2 3/8" T-BOLT
4 3/8 x 1 1/4" CARRIAGE BOLT
NOTE: READ THE ASSEMBLY AND INSTALLATION INSTRUCTI ONS COMPLETELY BEFORE YOU BEGIN.
THIS INSTALLATION REQUIRES CUTTING THE LOWER BUMPER VALANCE ON MODELS WITHOUT FACTORY TOW
HOOKS.
INSTALLATION
STEP 1. IF THE VEHICLE IS EQUIPPED WITH FACTORY TOW HOOKS, BEGIN THE INSTALLATION ON THE PASSENGER
SIDE. LOCATE AND REMOVE THE TOW HOOK BOLT TOWARD THE FRONT OF THE VEHICLE, LOOSEN THE REAR BOLT
AND REMOVE THE TOW HOOK. SEE DIAGR AM #1
NOTE: IF THE VEHICLE IS NOT EQUIPPED WITH FACTORY TOW HOOKS PROCEED TO STEP 3.
STEP 2. POSITION THE PASSENGER SIDE LOWER BRACKET OVER THE REAR TOW HOO K BOLT, THEN RE-INSTALL THE
TOW HOOK AND FRONT BOLT. DO NOT TIGHTEN. SEE DIAGRAM #2
REPEAT THE ABOVE PROCEDURE TO INSTALL THE DRIVER SIDE LOWER BRACKET.
3000 SERIES STEPGUARD
GRILLE GUARD INSTALLATION INSTRUCTIONS
PART NO. 3293B & 3293M 2009 FORD F-150 2/4WD
Do not attempt to install this product on any vehicle other than the one it is designed for and listed above!
#1
#2
REMOVE TOW HOOK
TOW HOOK BOLTS
PASSENGER SIDE LOWER BRACKET
STEP 3. IF THE VEHICLE IS NOT EQUIPPED WITH FACTORY TOW HOOKS, USE THE SUPPLIED TEMPLATE AS A GUIDE TO
MODIFY THE LOWER BUMPER VALANCE. ALIGN THE TEMPLATE WITH T HE EDGES AS SHO W N. SEE DIAGRAM #3.
USE A UTILITY KNIFE OR DREMEL TOOL TO CUT THE VALANCE. REPEAT THE PROCEDURE FOR THE DRIVER SIDE.
NOTE: BEFORE PROCEEDING WITH THE BUMPER VALANCE MODIFICATION, MAKE SHURE THAT THE TEMPLATE AND THE
PRINTED DIMENSIONS ARE THE SAME. PROFESSIONAL INSTALLATION IS RECOMMENDED.
STEP 4. AFTER CUTTING THE BUMPER VALANCE INSTALL THE ½” TAB BOLTS IN THE FRAME RAIL USING THE WIRE GUIDE.
SEE DIAGRAM #4
STEP 5. ATTACH THE PASSENGER SIDE LOWER BRACKET TO THE BOTTOM OF THE FRAME USING ½” FLAT WASHERS,
LOCK WASHERS AND HEX NUTS. DO NOT TIGHTEN. SEE DIAGRAM #5
REPEAT THE STEPS TO INSTALL THE DRIVER SIDE LOWER BRACKET.
STEP 6. LOCATE THE BUMPER SUPPORT BRACKET AND REMOVE THE UPPER BOLT. SEE DIAGRAM #6
LOCATE THE LARGE ROUND HOLE IN THE SIDE OF THE FRAME. INSERT
3/8” T-BOLT INTO THE HOLE AND INSTALL
(1) VI
NYL GASKET OVER THE THREADS TO PREVENT THE T-BOLT FROM FALLING INTO THE FRAME.
STEP 7. ATTACH THE AUXILIARY UPPER BRACKET TO THE BUMPER SUPPORT USING M8 X 40M HEX BOLT AND 5/16” FLAT
WASHE
R, AND TO THE FRAME USING THE 3/8” T-BOLT,
FLAT WASHER, LOCK WASHER AND HEX NUT. DO NOT TIGHTEN.
SEE
DIAGRAM #7
#3
#4
#5
#6
CUT AND REMOVE THE
RETANGULAR AREA
INSERT TAB
BOLTS HERE
T-BOLT &
VINYL GASKET
BUMPER SUPPORT
BRACKET UPPER BOLT
ALIGN THE EDGES
½” TAB BOLTS
½” TAB BOLTS, FLAT WASHERS, LOCK
WASHERS AND HEX NUTS
STEP 8. FROM THE FRONT OF THE VEHICLE, PULL UP ON THE BUMPER COVER AND INSERT THE PASSENGER SI DE UPPER
BRACKET THROUGH THE GAP BETWEEN THE COVER AND BUMPER. ATTACH THE UPPER BRACKET TO THE AUXILIARY
BRACKET USING
3/8” X 1 1/4” CARRI
AGE BOLT, FLAT WASHER AND LOCK NUT. DO NOT TIGHTEN. SEE
DIAGR
AM #8
REPEAT THE STEPS TO INSTALL THE DRIVER SIDE UPPER BRACKET S.
3/8” X 1 1/4” CARRIAGE BOLT, FLAT
W
ASHER, LOCK NUT
STEP 9. ATTACH THE GRILLE GUARD ASSEMBLY TO THE LOWER BRACKETS USING 1/2” X 1 1/4” CARRIAGE BO LTS, FLAT
WASHERS AND LOCK NUTS AND TO THE UPPER BRACKETS USING 3/8” X 1 ¼” CARRIAGE BOLTS, FLAT WASHERS AND
LOCK NUTS. SEE DIAGRAM #9
STEP 10. ALIGN THE GRILLE GUARD ASSEMBLY WITH THE FRONT OF THE VEHICLE AND TIGHTEN ALL ASSEMBLY AND
INSTALLATION NUTS AND BOLTS. SEE DIAGRAM #10
IMPORTANT: CAREFULLY OPEN THE HOOD AND CHECK FOR CLEARANCE BETWEEN THE GRILLE AND GRILLE GUARD TOP
TUBE. IF NECESSARY, LOOSEN THE MOUNTING BRACKETS AND ADJUST.
UPPER
BRACKET
#9
#10
#7
#8
M8 X 40M HEX BOLT &
5/16” FLAT WASHER
AUXILLIARY
UPPER BRACKET
UPPER
BRACKET
LOWER
BRACKET
GO RHINO BULL BARS
GRILLE GUARDS
Loading...