Go Rhino 3293B, 3293C Assembly Instructions Manual

PARTS LIST

QTY

PART DESCRIPTION

10 3/8” X 1 1/4” HEX BOLT
10 3/8” LOCK WASHER

4 3/8” HEX NUT
4 3/8” FLAT WASHER

QTY PART DESCRIPTION

2 3293 SIDE PLATE
1 ST3293 3” X 38 1/4” BOTTOM STEP TUBE
1 CP3293 38 1/4” CENTER PLATE
1

TT3293 2” X 38 1/4” TOP TUBE

ASSEMBLY INSTRUCTIONS

NOTE: READ THE ASSEMBLY AND INSTALLATION INSTRUCTIONS COMPLETELY BEFORE YOU BEGIN.
THIS INSTALLATION REQUIRES CUTTING THE LOWER BUMPER V ALANCE ON MODELS WITHOUT FACTORY

TOW HOOKS.

STEP 1. BEGIN THE GRILLE GUARD ASSEMBLY BY LAYING THE COMPONENT S OUT ON A PROTECTIVE SURFACE.
STEP 2. POSITION THE GRILLE GUARD SIDE PLATES WITH THE FRONT EDGE DOWN AND THE TOP AND BOTTOM

STEP TUBE BETWEEN THE SIDE PLATES.
STEP 3. ATTACH THE TOP AND BOTTOM STEP TUBE TO THE SIDE PLATES USING THE 3/8” X 1 1/4” HEX BOLTS AND

LOCK WASHERS. DO NOT TIGHTEN.

STEP 4. POSITION THE CENTER PLATE BETWEEN THE GRILLE GUARD SIDE PLATES, WITH THE SLOTTED
MOUNTING HOLES IN THE CENTER PLATE DOWN.

STEP 5. INSERT THE 3/8” X 1 ¼” HEX BOLTS THROUGH THE HOLES IN THE SIDE PLATES AND CENTER PLATE, AND

INSTALL THE 3/8” FLAT WASHERS, LOCK WASHER AND HEX NUTS. DO NOT TIGHTEN.
STEP 6. ALIGN THE GRILLE GUARD, AND TIGHTEN ALL NUTS AND BOLTS.

3000 SERIES STEPGUARD

GRILLE GUARD ASSEMBLY INSTRUCTIONS

PART NO. 3293B & 3293C 2009 FORD F-150 2/4WD

Do not attempt to install this product on any vehicle other than the one it is designed for and listed above!

3/8” X 1 ¼” HEX BOLTS & LOCK WASHERS

3/8” HEX NUTS, LOCK WASHERS & FLAT WASHERS

3/8” X 1 ¼” HEX BOLTS

SIDE PLATE

TOP TUBE

CENTER PLATE

STEP TUBE

.

PARTS LIST

QTY

PART DESCRIPTION

1 DRIVER SIDE AUXILIARY UPPER BRACKET
1 DRIVER SIDE LOWER BRACKET
1 DRIVER SIDE UPPER BRACKET
1 PASSENGER SIDE LOWER BRACKET
1 PASSENGER SIDE UPPER AUXILIARY BRACKET
1 PASSENGER SIDE UPPER BRACKET
2 VINYL GASKET
1 WIRE GUIDE
2 M8-1.25 x 40M HEX HEAD BOLT
2 5/16" FLAT WASHER
8 1/2" FLAT WASHER
4 1/2" HEX NUT

QTY

PART DESCRIPTION

4 1/2" LOCK NUT
4 1/2" LOCK WASHER
4 1/2" TAB BOLT
4 1/2 x 1 1/4" CARRIAGE BOLT
6 3/8" FLAT WASHER

2 3/8" HEX NUT
4

3

/8" L

OCK NUT

2 3/8" LO

CK WASHER
2 3/8" T-BOLT
4 3/8 x 1 1/4" CARRIAGE BOLT

NOTE: READ THE ASSEMBLY AND INSTALLATION INSTRUCTI ONS COMPLETELY BEFORE YOU BEGIN.
THIS INSTALLATION REQUIRES CUTTING THE LOWER BUMPER VALANCE ON MODELS WITHOUT FACTORY TOW

HOOKS.

INSTALLATION

STEP 1. IF THE VEHICLE IS EQUIPPED WITH FACTORY TOW HOOKS, BEGIN THE INSTALLATION ON THE PASSENGER

SIDE. LOCATE AND REMOVE THE TOW HOOK BOLT TOWARD THE FRONT OF THE VEHICLE, LOOSEN THE REAR BOLT
AND REMOVE THE TOW HOOK. SEE DIAGR AM #1

NOTE: IF THE VEHICLE IS NOT EQUIPPED WITH FACTORY TOW HOOKS PROCEED TO STEP 3.

STEP 2. POSITION THE PASSENGER SIDE LOWER BRACKET OVER THE REAR TOW HOO K BOLT, THEN RE-INSTALL THE

TOW HOOK AND FRONT BOLT. DO NOT TIGHTEN. SEE DIAGRAM #2
REPEAT THE ABOVE PROCEDURE TO INSTALL THE DRIVER SIDE LOWER BRACKET.

3000 SERIES STEPGUARD

GRILLE GUARD INSTALLATION INSTRUCTIONS

PART NO. 3293B & 3293M 2009 FORD F-150 2/4WD

Do not attempt to install this product on any vehicle other than the one it is designed for and listed above!

#1

#2

REMOVE TOW HOOK

TOW HOOK BOLTS

PASSENGER SIDE LOWER BRACKET