Go Rhino 3128MB, 3128MC Installation Instructions Manual
3000 SERIES STEPGUARD
3000 SERIES STEPGUARD
3000 SERIES STEPGUARD3000 SERIES STEPGUARD
COMPLETE GRILLE & BRUSH GUARD
ASSEMBLY INSTRUCTIONS
PART NO. 3128MB & 3128MC 2009/2013 DODGE RAM 1500 2/4WD
Do not attempt to install this product on any vehicle other than the one it is designed for and listed
Do not attempt to install this product on any vehicle other than the one it is designed for and listed
Do not attempt to install this product on any vehicle other than the one it is designed for and listedDo not attempt to install this product on any vehicle other than the one it is designed for and listed
PARTS LIST
QTY
QTY
QTYQTY
PART DESCRIPTION
4 ¼” x 1” button head bolt 2 31283AA side plate
8 5/16” x 1” button head bolt 1 3218P passenger brush guard
8 5/16” lock nut 1 3218D driver brush guard
8 3/8” x 1 1/4” button head bolt 1 D6P passenger head light protector
4 3/8” x 1 1/4” hex bolt 1 D6D driver head light protector
8 3/8” lock washer 1 ST3934 3” x 39 ¾” bottom step tube
QTY
QTY
QTYQTY
PART DESCRIPTION
above!
above!
above!above!
4 3/8” hex nut 1
4 3/8” flat washer
8 5/16” flat washer
Assembly
Assembly
AssemblyAssembly
Read the assembly and installation instructions completely before you begin.
Read the assembly and installation instructions completely before you begin.
Read the assembly and installation instructions completely before you begin.Read the assembly and installation instructions completely before you begin.
This installation requires cutting the bumper air dam.
This installation requires cutting the bumper air dam.
This installation requires cutting the bumper air dam.This installation requires cutting the bumper air dam.
Step 1.
Step 1. Begin the assembly by laying the components out on a protective surface.
Step 1. Step 1.
Step 2.
Step 2. Position the grille guard side plates with the front edge down and the top and bottom step tube
Step 2. Step 2.
between the side plates.
Step 3.
Step 3. Attach the top tube to the side plates using (2) 3/8” x 1 1/4” hex bolts and lock washers. Do not tighten.
Step 3.Step 3.
Step 4.
Step 4. Attach the step tube to the side plates using (4) 3/8” x 1" button head bolts. Do not tighten.
Step 4.Step 4.
Step 5.
Step 5. Position the center plate between the grille guard side plates, with the slotted holes
Step 5.Step 5.
down. Attach the center plate to the side plates using (4) 3/8” x 1” button head bolts, flat washers, lock
washers and hex nuts. Do not tighten.
Step 6.
Step 6. Align the grille guard, and tighten only the center plate and step tube nuts and bolts.
Step 6. Step 6.
Do not tighten the top tube.
Do not tighten the top tube.
Do not tighten the top tube.Do not tighten the top tube.
31288AA 2” x 39 ¾” top tube
1
CP3934L 39 ¾” center plate
slotted holes in the center plate
slotted holesslotted holes
Begin the installation. After completing steps 1-9 of the installation, refer to the assembly instructions
diagram to attach the brush guards and head light protectors.
3/8” hex nuts, lock &
Top tube
flat washers
Center plate
3/8” x 1 ¼” hex bolt & lock washer
5/16” lock nuts
3/8” x 1 ¼” hex bolt & lock washer
5/16” x 1” button head bolts
¼” x 1” button head bolts
Brush guard
Bottom step tube
3/8” x 1” button head bolts
5/16” x 3/4” button head bolts
Head light protector
Side plate 3/8” x 1” button head bolts
Loading...