Google jamboard User Manual
User Manual (English)
Safety Instructions
Safety precautions and maintenance
WARNING: Use of controls, adjustments or procedures other than those specified in this
document may result in exposure to shock, electrical hazards and/or mechanical hazards.
• Consult a service technician if the Jamboard does not operate normally when you have followed the instructions
in this manual.
• The casing cover should be opened only by qualified service personnel.
• Keep the Jamboard dry. To avoid electric shock, do not expose it to rain or excessive moisture.
• To avoid the risk of shock or permanent damage to the set do not expose the Jamboard to rain or excessive moisture.
• For doors or covers intended to be removed by operator for installation of accessory devices, instructions shall be
provided for the correct removal and reinstallation of the door.
Maintenance:
• To protect the Jamboard from possible damage, do not put excessive pressure on the LCD panel. When moving
the Jamboard, grasp the frame to lift; do not lift the display by placing your hand or fingers on the LCD panel.
• Unplug the Jamboard if you are not going to use it for an extensive period of time.
• The Jamboard touch-display may be wiped with a dry cloth. However, never use organic solvent, such as, alcohol,
or ammonia-based liquids to clean the Jamboard.
• To avoid the risk of shock or permanent damage to the set, do not expose the Jamboard to dust, rain, water or an
excessively moist environment.
Read and follow these instructions when connecting and using the Jamboard:
Operation:
• Keep the Jamboard out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into ventilation holes or prevent proper cooling of the display’s electronics.
• Do not block the ventilation holes on the back of the display.
• When positioning the Jamboard, make sure the power plug and outlet are easily accessible.
• When turning off the Jamboard by detaching the power cord, wait 6 seconds before re-attaching the power
cord for normal operation.
• Ensure the use of an approved power cord provided by Google at all times. If your power cord is missing,
please contact your local service center.
• Do not subject the Jamboard to severe vibration or high impact conditions during operation.
• Do not knock or drop the Jamboard during operation or transportation.
• Unplug the Jamboard if you are not going to use it for an extensive period of time.
• Unplug the Jamboard if you need to clean it with a slightly damp cloth. The screen many be wiped with
a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids.
IMPORTANT: Always activate a moving screen saver program when you leave the Jamboard unattended. Always activate a
periodic screen refresh application if the unit will display unchanging static content. Uninterrupted display of still or static images
over an extended period may cause “burn in”, also known as “after-imaging” or “ghost imaging”, on your screen. This is a wellknown phenomenon in LCD panel technology. In most cases, the “burned in” or “after-imaging” or “ghost imaging” will disappear
gradually over a period of time after the power has been switched off.
WARNING: Severe “burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired. This is also not
covered under the terms of your warranty.
RF Warning:
Federal Communication Commission Interference Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
• If the Jamboard becomes wet, wipe it with dry cloth as soon as possible.
• If a foreign substance or water gets in the Jamboard, turn the power off immediately and disconnect the power cord.
Then remove the foreign substance or water, and send the unit to the maintenance center.
• Do not store or use the Jamboard in locations exposed to heat, direct sunlight or extreme cold.
• In order to maintain the best performance of the Jamboard and ensure a longer lifetime, we strongly recommend using
the Jamboard in a location that falls within the following temperature and humidity ranges.
-- Temperature: 0-40°C 32-104°F
-- Humidity: 20-80% RH
Service:
• The casing cover should be opened only by qualified service personnel.
• If there is any need for repair or integration, please contact your local service center.
• Do not leave the Jamboard under direct sunlight.
!
If the Jamboard does not operate normally, having followed the
instructions set out in this document, please contact a technician
or your local service center.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Frequency Band EIRP (dBm) EIRP (mW)
2402 - 2480 MHz (Bluetooth) 12 16
2412 - 2472 MHz 20 100
5180 - 5320 MHz 23 200
5500 - 5700 MHz 23 200
5745 - 5825 MHz 14 25
The 5150 - 5350 MHz is restricted indoor use only
AT BE BGCH CY CZ DE DK EE PT SI
ES
FI FR GB GR HU HR IE IT RO SK
IS LI LT LU LV MT NL NO PL SE TR
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
Federal Communications Commission (FCC) Notice (U.S. Only):
NOTE: This equipment has been tested and found to comply with the limits for a Class A digita device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
End-of-Life Disposal
Your new Jamboard contains materials that can be recycled and reused. Specialized companies can
recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of.
Please find out about the local regulations on how to dispose of your old display from your local dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations.
For additional information on recycling contact www.eia.org (Consumer Education Initiative).
EC Declaration of Conformity
This device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member
States relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), RoHS directive (2011/65/EU) and
Radio Equipment Directive (2014/53/EU).
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 20 cm between the radiator & your body.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another
transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be
maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains
FCC ID: ARS-SMMTN28C01”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module
in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory
information/warning as show in this manual.
Loading...