Good Way Technology TD14000Z1 Users Manual

the delay duration is 1

R.G.B.W.

Color LED

Dimmer

User's Manual

Introduction

The RGBW Controller The RGBW Controller uses PWM output signal, which enables RGB, RGBW strips, Halogen lights. Controlled devices may 24

VDC.

is a

universal, Z-Wave compatible RGB / RGBW controller.

All IN

and OUT terminals can be configured

Package

■

■ 3M Double-sided Adhesive Sticker x1

■ User Manual x1

■ 18AWG copper wire x1

■ Conductive connector x1

Contents

R.G.B.W. Col or LED

Dimmer x1

it to

be powered by 12 or

for LED

control

Command Class

Multilevel Switch

GENERIC_TYPE_SWITCH_MULTILEVEL SPECIFIC_TYPE_POWER_SWITCH_MULTILEVEL

Multilevel Switch

COMMAND_CLASS_ZWAVEPLUS_INFO_V2 COMMAND_CLASS_VERSION_V2 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_DEVICE_RESET_LOCALLY, COMMAND_CLASS_POWERLEVEL_V1 COMMAND_CLASS_BASIC_V1 COMMAND_CLASS_SWITCH_MULTILEVEL_V2 COMMAND_CLASS_SWITCH_COLOR_V2 COMMAND_CLASS_CONFIGURATION_V1 COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 COMMAND_CLASS_SWITCH_BINARY_V1 COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2

Detailed description

ZWAVEPLUS INFO command class

The Z-Wave Plus Info Get Command is used to get additional information of the Z-Wave Plus device in question.

BASIC command class

The module will be turned ON or OFF after receiving the BASIC_SET command. To be turned on: [Command Class Basic , Basic Set, Basic Value = 0x01~0x63 in percentage; FF set to last value] To be closed: [Command Class Basic , Basic Set, Basic Value = 0x00]

SWITCH MULTILEVEL command class

The module will be turned ON or OFF after receiving the SWITCH_ MULTILEVEL_SET command. To be turned on: [Command Class Multilevel , Multilevel Set, Basic Value = 0x01~0x63 in percentage; FF set to last value] To be closed: [Command Class Multilevel , Multilevel Set, Basic Value = 0x00]

SWITCH COLOR command class

This class is used for Color setting. See the following table for configuration variables:

Capability ID Color State Level

0 (0x00) Warm White 0x00-0xFF

2 (0x02) Red 0x00-0xFF

3 (0x03) Green 0x00-0xFF

4 (0x04) Blue 0x00-0xFF

DEVICE RESET LOCALLY command class

The Device Reset Locally Command Class is used to notify central controllers that a Z-Wave device is resetting its network specific parameters.

VERSION command class

The user can enquire the version of the unit using VERSION_GET command. It will return Version Report Command: [Command Class Version, Version Report, Z-Wave Library Type, Z-Wave Protocol Version, Z-Wave Protocol Sub Version, Application Version, Application Sub Version]

MANUFACTURER SPECIFIC command class

The user can use the Manufacturer Specific Get Command to request manufacturer specific information from another node. Manufacturer Specific Report Command: [Command Class Manufacturer Specific, Manufacturer ID 1, Manufacturer ID 2, Product Type ID 1, Product Type ID 2, Product ID 1, Product ID 2]

CONFIGURATION command class

This class is used for setting certain vendor specific configuration variables. See the following table for configuration variables:

ID Name Size Range

Switch Type 1 byte 1-2 1 1:Toggle Mode

1 (0x01)

Device Information

Command

VERSION_REPO RT

Class

each command

Command.

Default value

class

Description

2: Momentary Mode

ID Name Size Range

Switch mode

(0x02)

Auto Scene

3 (0x03)

Mode Set

Auto Scene

4 (0x04)

LED,

Mode Duration

ASSOCIATION command class

The Module can be set 1 auto-report ID in Group 1. The Module will send BASIC_REPORT to device associated in Group 1 when correspond Device is activated.

FIRMWARE UPDATE META DATA command class, version 2

Support OTA (On-The-Air) firmware update function.

Product

1 byte 1-3 1 1: Normal Mode

1 byte 1-5 - 1: Ocean

1 byte 0x03-

Overview

0xFE

Default value

40.5

Device

Installation

1. Prepare the following items:

- RGBW strip(12V or 24V) x1

- Stranded wire x5

- Power adapter x1

2. Figure 1. Terminals Description.

Include/Exclude Button

3. Connect the R.G.B.W. Color LED Dimmer according to Figure 2., or Figure 3.

- First, connect RGBW strip with output channel(R,G,B,W)

- Second, connect the power supply. If the device is properly connected, the RGBW strip will blink once. Note that the device must be powered by a dedicated stabilized power adapter.

Figure 1. Terminals Description

Figure 2. Connecting toggle switch

Description

2: Brightness Mode 3: Rainbow Mode

2: Lightning 3: Rainbow 4: Snow 5: Sun

Adjust Scene delay time:

1. When Value is 1(0x01)~127(0x7F), the delay duration is 1 sec.~127 sec.

2. When Value is 128(0x80)~255(0xFE),

min.~127 min.

14.5

IN2

IN1

GND

12/24VDC

Figure 3. Connecting push switch

Figure 4. Connecting conductive connector

4. According to the Figure 4.,you can use the 18AWG copper wire and conductive connector to extend the connection of the power supply.

5. In the status of the factory default (Not Paired), the red light and green light will blink by turns, eg. red, green, red, green, etc..

6. Include the R.G.B.W. Color LED Dimmer into the Z-wave network, press 3 times in 2 seconds. If the device is properly included, the green light will remains on.

7. Exclude the R.G.B.W. Color LED Dimmer into the Z-Wave network, press 3 times in 2 seconds. If the device is properly excluded, the green light will blink and the data will be reset to the factory default values.

8. Please pull out the antenna and keep it at 90 degree to enhance the RF signals.

9. Support auto inclusion: Install the device, connect with the power, and the auto inclusion function will work in about 2 minutes.

10. Support remote exclusion: Through configuration setting. Please refer to the following table.

ID Size Value

F0 1 byte 1

Warning!

1) The RGBW Controller is suggested to operate in low voltage

circuits of 12VDC or 24VDC. Connecting higher voltage load may result in the RGBW Controller damage. Please refer to the following table.

Current of RGBW Strip Stranded Wire

High current 18 AWG

Low current 22 AWG

2) The RGBW Controller must be powered by the same voltage

as the connected light source. I.e. if controlling 12V LED strip, the module must be connected to 12V power supply. Similarly, if controlling 24V RGBW strip, the RGBW Controller must be powered by 24V voltage supply.

3) The RGBW Controller must be powered by 12VDC or 24 VDC

IN4

IN3

stabilized power supply with outputs load capacity matched to loads voltage.

4) In case of connecting long RGBW/RGB/LED strips voltage drops

may occur, resulting in lower light brightness further from R/G/B/W outputs. To eliminate this effect it's recommended to connect few shorter strips in parallel connection instead of one long strip connected serially. Maximum recommended wire length, used to connect R/G/B/W outputs with a RGBW/RGB/LED strip is 5 m. Observe connected loads manufacturer recommendations towards connection wire diameter.

5) For connection of IN1~IN4, it is suggested that you connect the 4 inputs individually to the same type of deivce. The devices can be as follows: the toggle switch, or the push switch.

6) Please note that re-including the product will reset the data to the default values. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.

Glossary

Include/Exclude Button - Inclusion/exclusion, press 3 times in 2 seconds

of terms

12/24VDC - Power supply signal IN4 - Switch input 4

GND - Power supply ground signal R - Output assigned to IN1

IN1 - Switch input 1 G - Output assigned to IN2

IN2 - Switch input 2 B - Output assigned to IN3

IN3 - Switch input 3 W - Output assigned to IN4

LED Dimmer

Color Control

Control the color with Hue (the palette on the top), Value (the first scroll bar), and Saturation (the second scroll bar).

Application

Multilevel Switch

Turn the switch ON/OFF (the button on the bottom), and adjust the brightness level (the scroll bar).

Special Scene Effect

Select the scene mode (the first drop-down menu), and the speed (the second drop-down menu).

Scene Mode: Tick the box to select from Ocean, Lightning, Rainbow, Snow, and Sun.

Speed: Tick the box to select Slow/ Medium/ Fast.

NOTE: Lightning Scene Mode does not support Speed adjustment.

LED

Indicator

Status LED Signal Remark

Not Paired Red& Green blinking

Paired up Solid Green

by turns

(Interval: 1sec.)

External Controller

Input type Remark

Momentary Momentary switch

oggle Toggle switch

Input operating

mode

Normal Each given switch key assigned to one

Brightness All channels are controlled together

Rainbow Transition through all colours spectrum

(Operates on RGB/RGBW channels only)

Device

Application

The RGBW Controller may control:

• 12 / 24VDC powered RGB strips

• 12 / 24VDC powered RGBW strips

• 12 / 24VDC powered LED strips, bulbs, etc.

• 12 / 24VDC powered halogen lights

Additional features:

• controlled by momentary or toggle switches

Remark

output channel

Specification

Item

Description

Power Supply 12 / 24V DC

PWM output frequency 488Hz

Electricity consumption 12V: 0.48W; 24V: 0.72W

Radio signal power 1mW

LED Indicator Red/Green *1

Button Inclusion/Exclusion

Protocol Z-Wave Plus

Operation Range 100 feet (About 30M)

Housing

Dimensions(L*W*H) 40.5*32*14.5mm

Rated output power

Max load

(e.g. halogen bulbs)

Application

Temperature

Region Applied

868.42 MHz 9.6 kbps

868.4 MHz 40 kbps

908.42 MHz 9.6 kbps

908.4 MHz 40 kbps

916 MHz 100 kbps

JP 922.5 MHz 100 kbps

JP 923.9 MHz 100 kbps

JP 926.3 MHz 100 kbps

*Specification is subject to change without prior notice.

Plastic

(PC8600)

7A for single output channel,

13A at max.

(3.25A for R.G.B.W. single output

channel is suggested)

At 12V- 192W

combined

At 24V- 384W

combined

Indoor use

Storage: -20℃~70℃

Operation:

0℃~40℃

Frequency Data Rate

Regulatory

CE Caution

Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1,000 MHz frequency range with power levels ranging up to 500 mW; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive.

FCC Caution

This device complies with Part 15 of the FCC rules standard. Operation is subject to the following two

conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.

WEEE Information

For EU (European Union) member users: According to the

WEEE (Waste electrical and electronic

equipment) Directive, do not dispose of this product as

household waste or commercial waste. Waste electrical and

electronic equipment should be appropriately collected and

recycled as required by practices

established for your country.

For information on recycling of this product, please contact

your local authorities, your household waste disposal

service or the shop where you purchased the product.

Z-Wave Plus

This product can be included and operated in any Z-Wave

network with other Z-Wave certified devices from other

manufacturers and/or other applications. All non-battery

operated nodes within the network will act as repeaters

regardless of vendor to increase reliability of the network.

Compliance

Good Way Technology TD14000Z1 Users Manual

Specifications and Main Features

Frequently Asked Questions

User Manual