CONFORMS TO UL STD 763, NSF/ANSI STD 8
CERTIFIED TO CSA STD C22.2 #195
CONFORMS TO CE, IEC TESTED
MANUAL
VERSION
SERIAL #
5.2
Introduction
WARNING : To limit risk of personal i njury and mater ial damage, all users mus t read these ins tructions
in their entirety a nd follow them strictly.
DANGER : This machine is not intended for use by persons (including child ren) with reduced phy sical,
sensor y, or mental capabilities, or la ck of experience a nd knowledge, unless they have been given super vision
or instr uction concerni ng use of the machine by a person responsible for their safe ty.
DANGER : Never place hands, ar ms, or any foreig n items into the grinder hopper, grinder chute, or g rinder
housing du ring operation. Persona l injury including lacer ations and amputat ions, or damage to the ma chine
can occur.
DANGER : Never place any b ody part bet ween the platens whi le the machine is on . Failure to follow t his
instr uction could resu lt in serious person al injury due to crushin g.
WARNING : Power must be supplied to the X-1 and EG-26 0 by a licensed electricia n. Failure to do s o may result
in seriou s personal injur y due to electric shock or damage to the machi ne.
WARNING : Be aware of all pi nch points and moving parts a nd take precautions to keep loose cloth ing, hair, or
foreign objects away from them t o avoid personal injury and dama ge to the machine.
WARNING : Disconnect a ll power before per forming maintena nce to avoid risk of ser ious electric shock.
WARNING : Always check with your loca l health depar tment regardi ng procedures re quired to ensure proper
cleaning and sanit ation in order to avoid serious foodborne ill ness to consumer s.
For the US: http ://w ww.fda.gov/Food /default.ht m
WARNING : Discontinue use immediately and have machine ser viced if any c omponents are dam aged or
malf unctioning to avoid risk of p ersonal injury and da mage to the machine.
WARNING : Disconnect a ll power before moving the machine. Avoid damagi ng the power supply cord du ring
movement and use cautionar y steps to avoid tipping.
WARNING : Electrica l and mechanic al repairs a re not to be carr ied out by the operator unless
authoriz ed to do so.
WARNING : Operator sha ll not interfere w ith interlock device .
WARNING : Operator should not use unaut horized means of gain ing access to parts of the ma chine which are
not normally accessible.
WARNING : Operator should en sure plug is visible f rom points of acces s.
WARNING : Operator should en sure the surrounding a rea is free of debris and sl ipping ha zards to
pr event i njury.
WARNING : In the event of an acc ident or breakdown , all power supply should be dis connected fr om source
and Goodnature customer ser vice should be cont acted for suppor t.
CAUTION: Sa fety glass es must be worn at al l times during operation of EG -260. Machine can be r un at a very
high sp eed; splatter a nd projectiles causing ey e damage and i rritation is pos sible.
CAUTION: Bla des on the grinder disc are very s harp. Use caution when chan ging the disc t o avoid personal
injury including lacerations.
NOTICE: T he X-1 Press is only t o be used in conjunction with the EG-260 G rinder. Do not mount any other
equipment to t he X-1 Press.
NOTICE: Noise levels exceed 80 de cibels. Protec tive ear equipment may be worn to prevent injur y.
This equipment underwent strict quality control and was carefully inspected mechanically and electrically before
shipment. It should be physically free of marks or scratches and in good electrical order upon delivery. Inspect for
physical damage, electrical damage, and any loose or bare wires.
If any items are damaged due to shipping, contact the freight carrier within 15 days of receiving your shipment.
There is an enclosed parts list below. Inspect a ll enclosed parts carefully and make sure no par ts are missing. If
any parts a re missing or damaged please contact Goodnature customer service.
After unpacking a nd before running, it is importa nt to check that none of the fasteners became loose during
shipping. Check all nuts, bolts, and screws to make sure everything is tight.
2.2 ENCLOSED PARTS LIST
PART #
19115
19680
18496-V3.5
11127
11128
11130
19103
12566
13967
19351
13778
19664
PART NAME
Press Rack
Juice Tray
Juice Collection Package
Grinder Disc 3/16”
Grinder Disc 1/4”
Grinder Disc 1/2”
Grinder Disc Backing Plate
Shredder Plate Knob
Shredder Plate Knob Washer
Hopper
Hopper Knob
Hopper Gasket
QTY
DESCRIPTION
20”x20” Ridged white plastic square
2
Stainless Steel pa n with flared hole in bottom
1
Shelf, plastic bucket a nd lid, juice collection tube, a nd grommet
1
Metal g rinder disc with small holes
1
Metal g rinder disc with medium holes
1
Metal g rinder disc with large holes
1
9” white plastic disc with raised spokes
1
Small stainless steel triang ular knob
1
Stainless steel washer for shredder plate knob
1
Stainless steel tube with square base
1
Black plastic knob
4
White “U” shaped gasket with four holes in the corners