golmar Plus Nexa Instruction Manual

Download

Plus Nexa

Code 50122328

Instructions manual

Audio and Video

door entry system

(One or several

accesses doors /

General door panel)

T632 PLUS NP/T E rev.0118

INTRODUCTION

STARTING RECOMMENDATIONS

INDEX

First of all we would like to thank and congratulate you for the purchase of this product manufactured by Golmar.

The commitment to reach the satisfaction of our customers is stated through the ISO-9001 certification and for the manufacturing of products like this one.

Its advanced technology and exacting quality control will do that customers and users enjoy with the legion of features this system offers. To obtain the maximum profit of these features and a properly wired installation, we kindly recommend you to expend a few minutes of your time to read this manual.

O Do not use excessive force when tightening the power supply connector screws. O The entire installation must be at least . away from any .40cm other installation O Before to connect the system, check the connections between door panel,monitors, telephones, and

the transformer connection. Do always follow the enclosed information.

O Each time thepower supply isrestarted, or after a modification, the system will remainblocked during

30 seconds.

O Always use coaxial cables, (see page 94).RG-59 B/U MIL C-17 or RG-11 Never use coaxial

antenna cable. Golmar RAP-5130In installations no longers than 100m., cable can be used.

Introduction ...........................................73

Index.....................................................73

Starting recommendations .......................73

Safety precautions...................................74

System characteristics ..............................74

Important notice .....................................75

System operation ....................................75

Door panel description ............................76

Modules description....................................

Sound moduleEL632 Plus P/T.................77

Sound moduleEL642 Plus ......................77

Pushbuttons module EL610D.................78

Door panel ................................................

Embedding box positioning ...................79

Embedding box installation ..............79-80

Assembly electronic modules .................80

Hold the Frame ....................................81

Pushbuttons connection...................81-82

Pushbuttons coding..............................82

Descrip i n con ector.............83t o Bus Nexa n

Con e ............83n ctionillumination module

Descrip ..................84tion illumination leds

Descrip .................84tion visual indications

Sound module configuration ............85-86

Programming(general panel) ...........87-89

Description Cn3 connector....................89

Finaladjustments .................................90

Place the nameplate labels ....................90

Door panel assembly ............................91

Close the door panel.............................91

Powersupply installation ..........................92

Lock release installation...........................92

Installation diagrams...................................

Video installation with coaxial ...........93-94

Video installation without coaxial.......95-96

Audio installation ............................97-98

Video installtion (general panel) ......99-102

Audio installation (general panel) ..103-104

Connection of an a.c. lock release ........105

Link of several power supplies...............105

Optional connections..................................

External lock release activation.............106

ConnectionsynthesevocalemoduleFDI..106

Troubleshooting hints ............................107

Notes...........................................108-110

Compliance.........................................111

O Audio and video door entry system with simplified installation:

O Sound module ( )with two operating modes EL500 or EL501 . O Sound module EL632 Plus P/T with pan and tilt mechanism to adjustthe telecamera position. O BusNexa: ( , manual )It allows the connection of illumination module coded panel see TCode/C NexaA

O Unlimited number of door panels (access) being not necessary the use of switching units. O Up to 120 monitors/telephones per installation or backbone. O General door panel (EL501 mode): Up to 120 monitors/telephones,distributedin max.120 buildings. O EL560 module for videoinstallations with twisted paircable, integratedin sound module. O Communications resistor for the system UNO orPLUS,integratedin sound module. O Acoustic busy channel and call acknowledgement signals. O Door opening timed at 3 seconds. O Input for external door release push button (timed at 3 or 15 seconds). O a.c or d.c lock release operated by relay. O Up to three monitors or telephones in the same apartment without additional power supplies. O Monitor Tekna Plus SE:

O TelephoneT540 PlusSE:

O TelephoneT540 Uno SE:

O Install or modify the equipment .without the power connected O The installation and handling of these equipments must be performed by .authorisedpersonnel O The entire installation must be at least . away from any .40 cm other installation O With power supply:

O With monitor, telephones and distributor:

O Remember, the installation and handling of these equipments must be performed by authorized

O Do always follow the enclosed information.

SAFETY PRECAUTIONS

SYSTEM CHARACTERISTICS

O Audio and video door entry system with simplified installation:

wAudio door entry system with 4 common wires installation. wVideo door entry system with 3 common wires plus coaxial cable installation.

wVideo door entry system with 4 common wires plus twisted pair installation. O Sound module ( )with two operating modes EL500 or EL501 . O Sound module EL632 Plus P/T with pan and tilt mechanism to adjustthe telecamera position. O BusNexa: ( , manual )It allows the connection of illumination module coded panel see TCode/C NexaA

(NFCmodule, see manual ).TCode/CA NFC Nexa

Description,installation,configurationand programming of themonitor (see manualTTEKNA PLUS SE "Code 50123594")availablein:

https://doc.golmar.es/search/manual/50123594.

O TelephoneT540 PlusSE:

Description, installation,configuration and programming of the telephone(seemanualT540 PLUSSE "Cód.50122199") disponible en:

https://doc.golmar.es/search/manual/50122199.

O TelephoneT540 Uno SE:

Description,installation, configuration and programmingof the telephone (see manual T540 UNO SE "Cód. ") disponibleen:50122257

https://doc.golmar.es/search/manual/50122257

wDo not use excessive force when tightening the connector screws.

wInstall the power supply in a dry and protected place without risk of drip or water projections.

wAvoid to place it near to heating sources, in dusty locations or smoky enviroments.

wDo not block ventilation holes of the unit so that air can circulate freely.

wTo avoid damage, the power supply has to be firmly fixed.

wTo avoidan electrical shock, neither remove the protection cover nor handle the connectedwire in

the terminals.

O With monitor, telephones and distributor:

wDo not use excessive force when tightening the connector screws.

wInstall the equipments in a dry and protected place without risk of drip or water projections.

wAvoid to place it near to heating sources, in dusty locations or smoky enviroments.

wDo not block ventilation holes of the equipments so that air can circulate freely. O Remember, the installation and handling of these equipments must be performed by authorized

personnel and in the absence of electrical current. O Do always follow the enclosed information.

O To make a call the visitor should press the push button corresponding to the apartment he wishes to

contact. An acoustic tone will be heard confirming the call is in progress once the push button has been pressed . At this moment the call will be received at theand the door panel led will turn on monitor (telephone) in the dwelling. During the call the visitor can correct his call by pressing a push button corresponding to a different apartment, in which case the original call is cancelled.

O In systems with several accesses doors, the other(s) door panel(s) will be automatically disconnected:

If a visitor tries to call from other door panel an acoustic tone will be heard and the door panel led will be on .confirming the system is busy

O General door panel (EL501 mode): If the call is made from the general door panel, the inner door

panel of the building called and other possible general door panel will remain automatically disconnected, if another visitor tries to call from an inner busy door panel an acoustic tone will be heard confirming the systemis busy or fromanother general doorand the doorpanel led will be on panel, an acoustic tone will be confirming the system is busy andheard the general door panel led will blink for 3 seconds. The door panels of the others inner buildings will remain free to be used.

O General door panel(EL501 mode):In thecase that thecall ismade froman inner doorpanel, therest

of inner door panels will remain free to be used. From general door panels only will be able to make calls to the inner buildings whose door panels are not in use, if the visitor tries to make a call to a busy inner door panel, an acoustic tone will be heard confirming the system is busy and the general door panel will blink for 3 secondsled .

The call lasts for 45 seconds, during which time an image appears on the apartment's monitors for 2 seconds after thecall isreceived withoutthe visitorknowing, and the statusLED onthe mastermonitor will illuminate (green). If the call is not answered within 45 seconds, the master monitor's status LED will illuminate (red), LED onthe door panel will turn off and the channel will be free.

O To establish communication, lift the handset of the monitor (telephone), and the monitor's status LED

(green) and the door panel's LED will illuminate

The communication will last for one and a half minutes or until the handset is replaced. After the communication, the monitor's status LED will illuminate (red), the door panel's LED will turn off and the channel will be free.

O To open the door, press the door release push button during call or communication progresses: with

one press, thedoor releaseoperates during 3seconds. Duringthe lock releaseactivation an acoustic tone will be heard on the door panel confirming the lock release is activated and the led will also turn on for 3 seconds.

SYSTEM OPERATION

Uno system:

O Tekna Uno monitor T-540 Uno telephone are fully compatible with Tekna Plus monitor T-and and

540 Plus telephone. However, a Uno communications resistor must be setting with the SW1 configuration dip switch of the door panel, see 85 .( page )

O If the distance from the door panel to the farest monitor or telephone is longer than 200 meters, or

the building has more than 200 apartment units, a repeater must be installed.RDPlus/Uno SE

IMPORTANT NOTICEIMPORTANT NOTICE

DOOR PANEL DESCRIPTION

Sound module

EL63 Plus P/T2 EL64 Plus2

oor panel description.

Push buttons electronic module

EL610D

Short connection cable, It is supplied with EL610D module (16 cm length).

, for 5 single push-buttons or 10 double push buttons.

, on video systems with color camera. , on audio systems.

Connection cable RAP-610D (27 cm length).

General detail of parts, for assembly the door panel.

Aluminium modules

Electronic

modules

Frame modulesEmbedding boxes

Push buttons module

Main module

Door panel description.

For the connection of the push-buttons between the sound module and the push

buttons module EL610D and between push-buttons modules EL610D.

For the connection of the push-buttons between the sound module and the push

buttons module EL610D and between push-buttons modules EL610D.

This cable is necessary when the distance between modules to connecting is

greater due to the distribution of these modules in the door panel/s.

Bus Nexa connection cable e th(l ng 50 cm).

For the connection of the or modules with others BusEL632 Plus P/T EL642 Plus

Nexa modules (see page ).83

ound module description (EL632 Plus P/T and EL642 Plus).

Note: See installation diagrams for wiring.

MODULES DESCRIPTION

Micr .ophone

Speaker.

Front side.

Sound module push buttons (x2).

Installation terminals CN1.

Push buttons connector CN6.

Back side.

: ontact . Rel 3."C" c free for lock release ay : . Rel 3."N.O" contact free for lock release ay : Positiv , .e ground : .Digital communication : .Audio output communication : .Audio input communication : .Twisted pair video signal input : .Twisted pair video signal output : .Coaxial shield : .Video signal coaxial input : .Video signal coaxial output

Color camera .(only EL632 PLUS module )P/T

CV1 CV2 +, D Aout Ain Vi+,ViVo+,VoMalla Vi+ Vo+

Monitor audio adjustment.

Leds (visual indications for people with impaired hearing).

Leds .illumination (only function with EL632 PLUS module)P/T

Bus Nexa c non ector CN8.

Configuration dip switch SW2.

Door panel audio adjustment.

Function connecto CN3.

Configuration dip switch SW1.

Push button number.

Door panel audio adjustment. Monitor audio adjustment.

ush buttons electronic module EL610D description.

Front side.

Push buttons module (x10).

Configuration dip switch (Push buttons call code).

Push button number.

Input/Output push buttons connector (x3).

Back side.

MODULES DESCRIPTION

90CS

CEA90C

143

Door panel

Model

90C

CEV90C

250

CEV90

99 mm.

328 mm.

56 mm.

1650

1850

1450

DOOR PANEL INSTALLATION

mbedding box positioning.

The upper part of the door panel should be placed at 1,65m. height roughly. The hole dimensions

will depend on the type of door panel.

The door panel has been designed to be placed under most of the environmental conditions.

However it's recommended to take additional cautions like rainproof covers. To obtain a good quality picture on video door entry systems, avoid direct incidence from light sources.

reparing the cables entry.

Break the bottom flange to pass the cables through. In case of door panels

with more than one embedding box, break the side flanges and attach the embedding boxes using UC junctions.

DOOR PANEL INSTALLATIONDOOR PANEL INSTALLATION

ssembly the electronic modules.

Insert the sound module in the top part of the module frame.

Align the tabs on the sound module in their respective housings of the module frame and later exercise a light pressure until correct placement.

Sound module EL632 Plus P/T EL642 Plus

Push buttons electronic

module EL610D

Frame

If there is push buttons module repeat the above process, locating under the sound module,

as shown in the drawing.

Frame

lace the embedding box.

Passthe wiringthrough thehole madein thebottom partof the

embedding box. Level and flush the embedding box. Once the embedding box is placed, remove the protective labels from the attaching door panel holes.

DOOR PANEL INSTALLATION

old the frame on the embedding box.

lug the push buttons with the short connection cable.

Between push buttons modules EL610D of the same embedding box,

insert the short connection cable of the low connector of the first push buttons module to the top connector of the second push buttons module, as shown in the drawing.

Insert the short connection cable that it is supplied with the product

EL610D, in the push buttons connector of the sound module and the other end of the connection cable in the connector placed in the top part of the push buttons EL610D module, as shown in the drawing.

Between push buttons modules EL610D ofdifferent embeddingt boxes,

insert the short connection cable in the low connector of the last module EL610D of the first embedding box and the other end of the connection cable in the middle connector of the last push buttons module EL610D placed in the low partof the second embeddingbox, as shown in the drawing.

Insert the hinge that it is supplied with the product in the embedding

box, as shown in the drawing.

To holdthe frame on the embedding box, insert the hinge in the

housings arranged for this purpose in the frame, as shown in the drawing.

The frame can now be folded horizontally facilitating the connection

and adjustments in the sound module and push buttons electronic module.

Use the connection cable RAP-610D, for the connection of the push buttons

The push buttons module EL610D must be configured, to assign a call code to

Depending on the setting selected, the push buttons are assigned to a specific

In case to combine these door panels with coded door panels or porter s'

(1)

( )

DOOR PANEL INSTALLATIONDOOR PANEL INSTALLATION

lug the push buttons with the connection cable RAP-610D.

onfiguration of the push-buttons code.

Push buttons module EL-610D

Dip1

Dip2

Dip3

Dip4

Dip5

Dip6

Dip7

Dip8

Push buttons code

Module configuration option

P1 P2 P3 P4 P5 P6 P7

P8 P9 P10

101

122

112

102

123

113

103

124

114

104

125

115

105

126

116

107

127

117

108

128

118

109

129

119

110

130

120

111

131

100

121

Dip switch

Off

Important: Select a different configuration option for each module EL610D.

P1- P10: Push button 1 to push button 10. Note:Sound module factory set the code " ., 106" 132"in P1 and " in P2

Use the connection cable RAP-610D, for the connection of the push buttons

between the sound module and the push buttons module EL610D and between push buttons modules EL610D, when the distance between modules to connecting is greater due to the composition of the door panels.

The push buttons module EL610D must be configured, to assign a call code to

the push buttons. Make this configuration with the dip switch placed in the back side of the module.

Depending on the setting selected, the push buttons are assigned to a specific

call code.

In case to combine these door panels with coded door panels or porter s'

exchange, it will be necessary to known the call code of each push button, as shown in the table below.

(1)

( )

Factory default.

( )

The connector CN8 Bus Nexa is located at the upper left side of the back of

the sound module.

Insert the connection cable that it is supplied with the module in the CN8

connector of the sound module and the other end of the connection cable in the module with connector Bus Nexa.

The modules to connect with connector Bus Nexa are the next :

ðN3403/AL: Con ect m duln to the o e to add to the system with a graphic display module (coded

panel, see manual)TCode/CD Nexa .

ðN3301/AL: Con ectn to the module to add to the system with an access control module and

coded panel, (see manual)TCode/CD Nexa .

ðN3301A/AL: Co nectn to the module to add to the system with an alphabetic module, (see

TCode/CD Nexa manual).

ðEL4502/NFC: Co nect an NFC access seen to the module to add to the system with control (

manu l )a .TCode/C NexaA NFC

ðEL3002: Con ect (M xim 2 ).n to power the illumination module a um EL3002modules ðCD-NEXA/BT: Con ectn to the module to add to the system with a configuration RFC interface

(wireless device of 2,4 Ghz). Onlyfor and modulesN3301 N3403 .

escription CN8 Bus Nexa connector.

on .nection with EL3002 illumination modules

Insert Bus Nexathe connection cable that it is

supplied with the product in the CN8, connector of the sound module and the other end of the connection cable in any of the three connectors placed at the bottom of the EL3002 illumination module.

To connect to other illumination modules use

any of the two free connectors.

NOT :E Only the or sound moduleEL632 Plus P/T EL642 Plus must be connected to power

supply The EL3002 illumination module take the power through Bus Nexa connection cable. (once the Bus Nexa connection cable has been connected in the sound module).

DOOR PANEL INSTALLATION DOOR PANEL INSTALLATION

DOOR PANEL INSTALLATION

The door panel illumination leds, will turn on during call and

communication progresses. Allowing us to see from apartment´s monitor the person who has called. Only sound( EL632 Plus P/T module .)

escrip .tion illumination leds

Visual indications on the door panel for people with impaired hearing:

- While calling: The led will turn on during the call time process.

- Duringcommunication: The led willturn on during communicationprocess.

- Duringdoorrelease: The led willturnon duringdoorrelease.

- End of communication:The led willturn off.

- In systems with several accesses doors in the buildingandone access doorpanel isin comunication: The otheraccessesdoors panels would havethe led of busysystem turn on until end communication.

- While callingand the monitor is switchoff:The led willblink during3 seconds.

escrip .tion visual indications leds

escription of the SW1 configuration dip-switch of the sound module.

Placed to OFF if the sound module is configured as EL500 .operating mode Set to ON if the sound module is configured as EL501 operating mode

(general door panel).

Selects the d done from the (AP' 'oor opening time, external push button

terminal), see page 106. Placed to ON:door opening timedat 3 seconds. Set to OFF:door opening timed at 15 seconds.

Selects the type of cable to be used for the video signal. Placed to OFF:coaxial cable RG-59 o RG-11. Set to ON:twisted pair.

Placed to OFF if the door panel has telecamera. In case of door panels without telecamera (EL642 Plus sound module) set to ON.

Plus system, loads the installation with a communications resistor . For aPlus

proper system operation, placed to ON only in the closestdoor panel to the

backbone installation or in the general door panel (if exists), set the rest to

OFF.

Set to ON so that the volume tone emitted by the door panel: (call reception, busy system and lockrelease) are or placed to OFF if aHIGH,

LOWvolume tone is desired.

Uno System, loadsthe installation with a communications resistor . For aUno

proper system operation, set to ON only in the closest door panel to the

backbone installation, placed the rest to OFF. With digital repeater RD Plus/Uno:

In the backbone installation or after the inner door panel in systems with

general door panels, placed the door panel/s to OFF.

Placed to ON, the calls made on the door panel will be transferred to the

porter's exchange(if exists).Set to OFF, the call is received in theapartment.

In general door panels systems with porter , this function is only's exchange

applicable to the general door panels not to the inner door panel/s.

Factory default

The SW1 configuration dip-switch is locatedat theupper right

side of the back of the module.

Not :e 9 10The dip-switches and without function.

DOOR PANEL INSTALLATION

inary coding of the SW2 configuration dip switch of the sound module.

The switches set to OFF have null value. The values of the switches

set to ON are shown in the enclosed chart. The backbone code will be calculated as the sum result of the switches values set to ON.

Example: 64+0+16+0+4+2+1=87

Switch number: ON value:

46453261678849210

escription of the SW2 configuration dip-switch of the sound module.

Allows to activate the autoswitch-on function (audio-video communication

without previous call) at thedoor panel that hasthis switch to ONposition. In systems with several door panels activate this function only in one of them; in systems with general door panel this function can be activated in one door panel of each inner backbone (building).

Set to ON for monitor or telephones programming. Once the programming

progress is finished return the switch to OFF position. The programming process is described on corresponding monitor / telephone manual, (see page 74 for manual web link).

In general door panel (EL501 mode), set to ON for general door panel

push buttons programming or backbone (building) monitor/telephones. The programming process is described on pages 87 to 89. Once the programming progress is finished return the switch to OFF position.

Set to OFF in case of a master door panel. Each system must have only one

master door panel; the rest must be slaves (ON).

In systems with general door panel, set as master one door panel of each

inner backbone (building) and the general door panel as slave. Of this way, theuser will be able to distinguish since door panel are calling him.

Switches number 4 to 10 set the building code. In backbones with several

door panels, set the same code in all the panels; in systems with general door panel, set different codes for each inner backbone (building). Set a code between 1 and 120 for inner backbones (up to 127 with coded panel) and a code 0 ( ) for general door panel/s. To set theFactory default code use binary coding as shown on the next paragraph.

Factory default

The SW2 configuration dip-switch is located at the upper left

side of the back of the module.

Configure the sound ofthe general door panel in EL501 mode, (see page 85).module

Locate the SW2 configuration dip switch of the general door

panel to program, placed at the upper left side (back) of the sound module.Withtheswitches 1 and 3 to OFF, set the switch 2 to ON: to show that the system is ready for programming, thegeneraldoorpanelwillreproducea tone.

Pick up the monitor/telephone handset of the apartment to

program and press the door release push button until to establish communication of audio with the general door panel.

Press the general door panel push button that will call to this

monitor or telephone. At this moment the general door panel will reproduce a tone. To finish the push button programmation, replace the monitor/telephone handset; to show that the push button has been succesfully programmed, the general door panel will reproduce a tone.

Make a call to check that the push button has been succesfully programmed.

Repeat these steps to program the rest of push buttons.

Once the programming has been finished, set to OFF the programming

switch. If you don't, the general door panel will reproduce a tone to advise that the system is still into programming mode.

eneral door panel (programming modes).

This programming modeallows toassign a monitor/ telephone(programmed) to thepush buttonof

the general door panel that it wishes to call.

Before the monitors/telephones of the inner door panel/smust be programmed, see the corresponding

monitor/ telephone manual, (see page 74 for manualweb link).

IMPORTANT: Before programming the general door panel push buttons, switch off the porter's

exchange (if exists).

Programming the push button (by call of monitor/telephone):

The general door panel permits the following programming modes:

O Programming the push button (by call of monitor). O Programming the push button (with a backbone code). O Programming the push button (with a monitor/telephone code). O Programming the monitor/telephone.

rogramming the push buttons of the general door panel.

GENERAL DOOR PANEL INSTALLATION

T-540 Plus SETekna Plus SE

GENERAL DOOR PANEL INSTALLATION

Define a backbone code to program with dip switches Sw2-4 to Sw2-

10. Set a code between 1 and 120. To set the code use binary coding,(seepage86).

Pressthe general doorpanel pushbutton thatis wishedhas this

backbone code. At this moment the general door panel will reproduce a tone, confirming that the push buttonhas been succesfully programmed.

Repeat these steps to program the rest of push buttons. Once the programming has been finished,

set to OFF the programming switch. If you don't, the general door panel will reproduce a tone to advise that the system is still into programming mode.

Programming the push button (with a monitor/telephone code):

This programming mode allows to assign a monitor/telephone code to push button of the general

door panel.

Locate the SW2 configuration dip switch of the general door

panel to program, placed at the upper left side (back) of the sound module. With the switches 1 and 3 to ON, set the switch 2 to ON: to show that the system is ready for programming, the generaldoor panel will reproduce a tone.

Pressthe general doorpanel pushbutton thatis wishedhas this

monitor/telephone code. At this moment the general door panel will reproducea tone,confirming that thepush button has been succesfully programmed.

Repeat these steps to program the rest of push buttons. Once the programming has been finished,

set to OFF the programming switch. If you don't, the general door panel will reproduce a tone to advise that the system is still into programming mode.

Define a monitor/telephone code to program with dip switches Sw2-4

to Sw2-10. Set a code between 1 and 120. To set the code use binary coding,(see page 86).

Programming the push button ( ):with a backbone code

This programmingmode allows to assigna backbone code to push button of the general doorpanel.

Locate the SW2 configuration dip switch of the general door

panel to program, placed at the upper left side (back) of the soundmodule. With the switch 1 to ON and 3 to OFF, set the switch 2 to ON: to show that the system is ready for programming, the generaldoor panel will reproduce a tone.

GENERAL DOOR PANEL INSTALLATION

DOOR PANEL INSTALLATION

This programming modeallows toassign toa monitor/ telephonea pushbutton ofthe generaldoor

panel that it wishes to call.

Before the push button of the general door panel must be programmed with backbone and

monitor/telephone code, (see page 88).

Programming the monitor/telephone:

Locate the SW2 configuration dip switch of the general door

panel to program, placed at the upper left side (back) of the soundmodule. With the switch 1 to OFF and 3 to ON, set the switch 2 to ON: to show that the system is ready for programming, the generaldoor panel will reproduce a tone.

Thenprogramthe monitor/telephone,as it is describedon correspondingmonitor / telephone manual,

(seepage 74 for manualweb link).

Bear in mind the configuration dip switch (as it is described in the previous step).

rogramming the monitors and telephones from a general door panel.

escription of the function connector CN3.

The function connectorCn3 islocated at theupper leftside of theback of

the sound module.

Plug the cable that is supplied with the module, to realize the following

functions:

837

Top view CN3

Description connector CN3

ð"AP" function: It activates the relay of the lock release "CV1" and "Cv2", configurable activation

time of 3 or 15 seconds via dip switch SW1-2(page 85), see connections (page 106).

ð"ICO"function:Forthe busychannel indication, it willbe realized with terminals"ICO" and "+12". ð"Handicap" function: Synthese vocale from FDI (France). The connector includes all wires for

connection (see page 106).

1 Grey (-) Ground. 2 Brown (+12) 12Vdc for activation the lock release. 3 White (ICO) Busy channel indicator. 4 Yellow (AP) External push button to activate the lock release. 5 Violet (+H) For activation of an external illumination. 6 Blue (OP) Handicap. 7 Orange (SC) Handicap. 8 Green (ALM) Handicap. 9 Red (PDB) Handicap. 10 Black (-) Ground.

DOOR PANEL INSTALLATION

inal adjustments.

lace the nameplate labels.

Open the label holder.

Place the label and

close.

Once finished the works of wiring, configuration and

final adjustments, fix the frame in the embedding box with the supplied screws.

lose the frame.

If after starting the system it's considered that the audio

volume isn't correct, proceed with the necessary adjustments as shown .

in the drawing

The telecamera has a pan and tilt mechanism built in to

adjust the telecamera position.

DOOR PANEL INSTALLATION

lose the door panel.

oor panel assembly.

In assemblies of a single door panel, it is ready from factory

to be mounted.

IMPORTANT:

To makethese adjustments of joining several door panels, see the

document that is supplied with the door panel and follow the steps that are described in the section" Mechanical assembly for double door panel" and once finished the adjustments stick the adhesive gasket (that is supplied with the push buttons module) in the rod of joining modules.

If the door panel to installing is of more than onemodule it will be

necessary make some adjustments to join a door panel with other one.

Fixthe door panel by using the supplied screws.

Finish the door panel assembly by placing the closing

heads, put thehead onone side andthen make aslight pressure on the other end, to its correct placement.

LOCK RELEASE INSTALLATION

nstalling the FA-PLUS and FA-PLUS/C power supplies.

DIN 46277

3,5 x 25

DIN-7971

3,5 x 25

DIN-7971

POWER SUPPLY INSTALLATION

ock release installation.

Replace the protection cover once the input terminals have been wired.

It's recommended to protect the power supply by using a

thermo-magnetic circuit breaker. Use a ground connection with FA-Plus power supply.

To install the power supply directly on the wall, drill two holes of

Ø6mm. and insert the wallplugs. Fix the transformer with the

specified screws.

The power supply can be installed on a DIN 46277

guide simply pressing it.

To disassemble the power supply from the DIN guide,

use a plain screwdriver to lever the flange as shown on the picture.

The FA-Plus/C model uses 6 units over DIN guide and

10 units the FA-Plusmodel.

IMPORTANT: the maximum number of units that can be connected to a FA-Plus/C power supply is

10, and 50 units in case of a FA-Plus model. Link power supplies to connect more units than the specified as it's shown on page 105.

If the lock release will be installed in a metal door, use a Ø3,5mm.

drill and tap the hole Ø3mm. drill. In case of wood door,use a .

Install the power supply in a dry and protected place without risk of drip or water projections. To avoid an electrical shock, neither remove the primary protection cover nor handle the connected

wire in the terminals.

The installation and handling of these equipments must be performed by authorised personnel and

without the power connected.

To avoid damage, the power supply has to be firmly fixed.

IMPORTANT:

- The lock relese must beof (Golmar) d.c or a.c12V . ( 05 93See page 1 (a.c lock release) and pages to 1 (d.c lock release04 ).

- A varistor is supplied with the sound module. In case to connect an a.c. lock release, place the varistor on the lock releaseterminals directly to ensure a proper system operation.

M 4 x 8

3,5 x 25

DIN-7972

DIN-963

FA-Plus/C o FA-Plus

SEC

PRI

+ +

Malla

out

CN4

Malla

out

CN4

Malla

out

CN4

D4L-PLUS

JP1

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

837

CN3

Main

Place this power supply as closest as possible to the first distributor.

Take off JP1 jumper of all the distributors except in the last one.

INSTALLATION DIAGRAMS

Access door panel

M =Master.

S =Slave.

Lock release

Vd.c.

SW1

SW2

FA-Plus/C

SEC

PRI

230110 0

+ + D

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

837

CN3

Main

ONE OR SEVERAL ACCESSES DOORS

ideo installation with coaxial cable.

1,00mm² 2,50mm²

0,25mm² 0,25mm²

RG-59 RG-59

Terminal

SECTIONS CHART

50m.

Distance

150m.

A , A , A, D

in out

V , V , V , V

in+ out+ in out

+, , CV1, CV2–

oaxial cable characteristics RG-59 B/U MIL C-17.

Core max. electrical resistence to 20ºC

Copper core Copper shield

ELECTRICAL CHARACTERISTICS

Nominal capacitance

Characteristic impedance

VALUES

Velocity of Propogation

Access door panel

* *

The installation diagram shows the connection of a video system with one or several door panels

for the same building. If the system has one access door panel only, overridethe wiring to the second door panel. If the system has more than one access door panel, wire the second panel as shown on the

diagram. In case of more than two door panels, wire them as the second is connected.

Lock release

Vd.c.

75 3

<67pf/m

<158 /Km <10 /Km

_ _

>66,6 %

SW1

SW2

INSTALLATION DIAGRAMS

FA-Plus/C o FA-Plus

SEC

PRI

+ +

JP1

AAD

A D

A D+

D6L-Plus/2H

VpM

A D

EL562 JP1

VpM

A D

EL562 JP1

JP1

AAD

A D

A D+

D6L-Plus/2H

VpM

A D

EL562 JP1

VpM

A D

EL562 JP1

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

837

CN3

* Place this power supply

as closest as possible to the first distributor.

Access door panel

M =Master.

S =Slave.

Lock release

Vd.c.

SW1

SW2

Main Main

* Take off JP1 jumper

of all the distributors except in the last one.

ONE OR SEVERAL ACCESSES DOORS

FA-Plus/C

SEC

PRI

230110 0

+ + D

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

837

CN3

1,00mm² 2,50mm²

0,25mm² 0,25mm²

CAT-5 CAT-5

Terminal

SECTIONS CHART

50m.

Distance

150m.

A , A , A, D

in out

V , V , V , M

in+,- out+,- p,d p,d

+, , CV1, CV2–

ideo installation without coaxial cable.

Lock release

Vd.c.

Access door panel

The installation diagram shows the connection of a video system with one or several door panels for

the same building. If the system has one access door panel only, overridethe wiring to the second door panel. If the systemhas morethan one accessdoor panel, wirethe secondpanel as shownon the diagram.

In case of more than two door panels, wire them as the second is connected.

IMPORTANT: For this type of installation, the door panels must have configured the switch nº.3 of

the SW1 configuration dip-switch to ON (page 85)in each and the monitors must

have an EL562 plugged in each (see page 74 for manual web link or QR in box

monitor).

SW1

SW2

INSTALLATION DIAGRAMS

FA-Plus/C o FA-Plus

SEC

PRI

+ +

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

837

CN3

Main

*Place this power supply

as closest as possible to the first telephone.

Access door panel

M =Master.

S =Slave.

Lock release

Vd.c.

SW1

SW2

T-540 Plus SE T-540 Plus SE

ONE OR SEVERAL ACCESSES DOORS

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

837

CN3

FA-Plus/C

SEC

PRI

230--110 0

+ +

Main

udio installation.

1,00mm² 2,50mm²

0,25mm² 0,25mm²

Terminal

SECTIONS CHART

50m.

Distance

150m.

A , A , A, D

in out

+, , CV1, CV2–

Lock release

Vd.c.

Access door panel

The installation diagram shows the connection of an audio system with one or several door panels

for the same building. If the system has one access door panel only, overridethe wiring to the second door panel. If the systemhas morethan one accessdoor panel,wire the secondpanel asshown on thediagram.

In case of more than two door panels, wire them as the second is connected.

SW1

SW2

To monitors

Main

Inner door panel

Main

General door panel

EL500 mode

BACKBONE 1

INSTALLATION DIAGRAMS

M =Master.

S =Slave.

BACKBONE 0

E S +

D4L-PLUS

JP1

FA-Plus o FA-Plus/C

SEC

PRI

+ +

FA-Plus/C

SEC

PRI

230--110 0

+ +

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

Lock release

Vd.c.

Lock release

Vd.c.

837

CN3

837

CN3

SW2

SW1

SW2

SW1

EL501 mode

100

To monitors

100

To monitors

Continues

in the following page

Main

EL501 mode

Main

General door panel

EL500 mode

BACKBONE 2

Inner door panel

GENERAL DOOR PANEL

BACKBONE 0

E S +

D4L-PLUS

JP1

SEC

PRI

+ +

FA-Plus o FA-Plus/C

FA-Plus/C

SEC

PRI

230--110 0

+ +

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

Lock release

Vd.c.

Lock release

Vd.c.

837

CN3

837

CN3

SW1

SW2

SW1

SW2

837

CN3

101

INSTALLATION DIAGRAMS

E S

D4L-PLUS

JP1

FA-Plus o FA-Plus/C

SEC

PRI

+ +

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

Coming

from previous page

ideo installation with general door panel

to large residential complexes.

Malla

Vin- Vin+ Vout-Vout+

Malla

Vin- Vin+ Vout-Vout+

IMPORTANT NOTES:

To install and configure properly,do always follow the enclosed information. The installation diagramshows the connectionof a video system with twogeneral door panelsand up to

120 inner door panels (backbones/buildings). In case of more than two door panels, wire them as the second is conected. In video systemsuse a D4L-Plus distributor before eachinner building except inthe last one. Take offJP1

jumper of all the distributors except in the last one. In video systems with use the D6L-Plus/2H distributor instead of D4L-Plus distributor. Takeofftwisted pair

JP1 jumper of all the distributors except in the last one. Add a negative in the inner building

installation riser,(see page 95). Below shows the connection of the twisted

pair instead of coaxial cable.

To monitors

Main

Inner door panel

EL500 mode

BACKBONE 119

Lock release

Vd.c.

SW2

SW1

102

To monitors

102

GENERAL DOOR PANEL

SEC

PRI

+ +

FA-Plus o FA-Plus/C

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

ideo installation with general door panel

to large residential complexes.

For greater distances contact our technical support department.

1,50mm² 2,50mm²

0,25mm² 0,25mm²

CAT-5

RG-59

Terminal

SECTIONS CHART

100m.

Distance

300m.

A , A , A, D

in out

V , V

in+ out+

V , V , V , V

in+ in out+ out- -

+, , CV1, CV2–

RG-59

CAT-5

Coaxial

Sw1-3 Off

Twisted pair

Sw1-3 On

Coaxial cable characteristics RG-59 B/U MIL C-17, (see page 94).

* *

To monitors

Main

EL500 mode

BACKBONE 120

Inner door panel

Lock release

Vd.c.

837

CN3

SW1

SW2

103

INSTALLATION DIAGRAMS

FA-Plus o FA-Plus/C

SEC

PRI

+ +

FA-Plus/C

SEC

PRI

230--110 0

+ +

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

To telephones

Main

General door panel

Inner door panelBACKBONE 1

EL501 mode

EL500 mode

BACKBONE 0

M =Master.

S =Slave.

837

CN3

837

CN3

Lock release

Vd.c.

Lock release

Vd.c.

SW2

SW1

SW2

104

To telephones

104

GENERAL DOOR PANEL

SEC

PRI

+ +

FA-Plus o FA-Plus/C

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

To telephones

udio installation with general door panel

to large residential complexes.

1,50mm² 2,50mm²

0,25mm² 0,25mm²

Terminal

SECTIONS CHART

100m.

Distance

300m.

A , A , A, D

in out

For greater distances contact our technical support department.

+, , CV1, CV2–

Main

IMPORTANT NOTES:

To install and configure properly,do always follow the enclosed information. The installation diagram shows the connection of an audio system with one general door panel

and up to 120 inner door panels (backbones/buildings).

In case of more than one general door panel, wire them as it shows in the video installation

diagram, (see page 99).

BACKBONE 120

Inner door panel

EL500 mode

837

CN3

Lock release

Vd.c.

SW1

SW2

105

INSTALLATION DIAGRAMS

onnexion of an a.c. lock release.

ink of several power supplies units.

1st FA-Plus 2nd FA-Plus/C or FA-Plus

SEC

PRI

Main

+ +

SEC

PRI

Main

+ +

If an alternating current lock release has been installed, use a TF-104 transformer and connect it to

the lock release as it is shown on the diagram.

If the quantity of monitors or telephones to be connected is bigger than the supported from one

power supply (see page 92), use additional power supplies to match the required quantity. The first power supply should be connected to the door panel and to the first group of monitors or telephones; connect the next groups to the positive terminal of its corresponding power supply.

To wire several power supplies link their ground terminals.

NEVER link positive terminals of different power supplies.

To the door panel & to the first

group of monitors/telephones.

To the second group of

monitors/telephones.

Main

CN1

- -

+CV1CV2

SEC

PRI

230110 0

+ +

EL632 PLUS P/T

EL642 PLUS

FA-PLUS/C

Main

TF-104

SEC

PRI

~ ~ ~ ~

Lock release

Va.c.

Important: Place the varistor supplied with the sound module on the lock release terminals

directly to ensure a proper system operation.

106

xternal lock release activation.

The lock release can be activated at any moment by using an

external push button, thatmust be connected between 'AP'and ' '– terminals of the connector Cn3 from door panel (see page 89).

Door opening timed at 3 or 15 seconds, with the help of the dip

switch SW1-2 (see page 85).

This function will allows toexit fromthe buildingbeing notnecessary

the use of a key.

Door panel

Lock release

Vd.c.

Main

To monitors

Main

onnection to the synthese vocale module of FDI (for France).

Lock release

Vd.c.

106

OPTIONAL CONNECTIONS

CN1

CV1CV2

837

CN3

FA-Plus/C FA-Plusor

SEC

PRI

+ +

Malla

Vin-AinAout Vin+ Vout-Vout+

CN1

+-+CV1CV2

837

CN3

PRI

SEC

TF-104

ALM

PDB

Red

Yellow

Green

12 -

12 +

ALM

PDN

PDB

MAS

PDG

GND

3 2 1

3 2

1 2 3

HCP

SYNTHESE VOCALE

SW2

SW1

TROUBLESHOOTING HINTS

An easy way to check that the system is working properly is to disconnect the wiring from the door panel

and to check the monitor directly connected to the sound module.

No shortcircuit will damagethe connected units, withthe exception of a shortcircuit between CTO and ' '–

monitor or distributor terminals.

O Nothing operates.

w –Check the output power supply voltage between ' ' and '+' terminals: it should have 17,5 to

18,5Vd.c. If not, disconnect the power supply from the installation and measure again. If it's correct now, it means there is a short circuit in the installation: disconnect the power supply from mains and check the installation.

w –Check that 'D' terminal is not shortcircuited with ' 'or '+' terminals. w Check that 'D' terminal hasn't been changed by 'A' terminal somewhere in the installation.

O Inappropriate audio level.

w Adjust the level volumes as shown on page 90. In case of feedback, reduce the audio levels until

feedback fade out. If feedback don't dissapears refer to the following hint.

O Continuous audio feedback.

w Check that 'A' terminal is not shortcircuited with other terminals.

O Door open function no operates.

w Remember that this function is only available during call and communication progresses. w The CV1 and CV2 terminals for door opening are voltage free outputs. The cable requires a

connection depending on whether 12Vdc or 12Vac is needed.(page to ) (page 10593 104 )

w Make a short circuit between the 'CV1' and 'CV2' terminals on the ; there shouldsound module

be12V (d.c. ora.c. depending on thetype doorrelease installed) between theterminals onthe door release. If so, check the lock release and its wiring.

O The system cannot be programmed.

w Check that the switch number 2 of the SW2 configuration dip switch is set to ON (see page 86)

and that the programming steps are correctly followed.

w Check that 'D' terminal is not shortcircuited with other terminals.

O Some units don't receive calls.

w Remember that each apartment musthave amaster unitonly. Check that the units are switchedon

and correctly programmed.

O There are no video image.

w Check the number 4 of the dip switch SW1 of the module 632 Plus P/T is in OFF (see page 85). w Check there is supply in the distributors, the voltage between '+' and '-' terminals should have 15

to 18 Vd.c.

O Push buttons don't work.

w Check that pressing the push button the door panel reproduce an acoustic confirming tone, if

not check the wiring and configuration of the push buttons (pages 81 to 82).

w If confirmation of pulsation exists, check the monitors or telephones programming on

corresponding monitor / telephone manual, (see page 74 for manual web link).

107

108

NOTAS/NOTES

110

109

110

NOTAS/NOTESNOTAS/NOTES

CONFORMIDAD/COMPLIANCE/CONFORMITÉ

Este producto es conforme con las disposiciones de las Directivas Europeas aplicables respecto a la Seguridad eléctrica y la Compatibilidad2014/35/CEE Electromagnética .2014/30/CEE

This product meets the essentials requirements of applicable European Directives regarding Electrical Safety Electromagnetic Compatibility20 / 5/ECC,14 3 20 4/ 0/ECC1 3 .

NOTA: El funcionamiento de este equipo está sujeto a las siguientes

condiciones: (1) Este dispositivo no puede provocar interferencias dañinas, y (2) debe aceptar cualquier interferencia recibida, incluyendo las que pueden provocar un funcionamiento no deseado.

NOTE: Operation is subject to the following conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any received interference, including the ones that may cause undesired operation.

111

Golmar se reserva el derecho a cualquier modificación sin previo aviso.

Golmar se réserve le droit de toute modification sans préavis.

Golmar reserves the right to make any modifications without prior notice.

golmar@golmar.es

www.golmar.es

Sistemas de comunicación S.A.

GOLMAR S.A.

C/ Silici, 13

08940- Cornellá de Llobregat

SPAIN

golmar Plus Nexa Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual