Golight Stryker Instruction Manual

Class B digital device. These limits are designed to provide reasonable

www.magnalight.com
1-800-369-6671
1-903-498-3363
[e-mail]

protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

✱ FCC RULE Part. 15.21 - Changes or modifications made by the

user not expressly approved by Golight, Inc. for compliance could void
the user’s authority to operate the equipment.

For safe and efficient operation of your Golight® Stryker™, observe
these guidelines:

Your Golight® Stryker™ is a radio transmitter and receiver operating
at 433MHz. Whenever the light is on, the internally mounted antenna
sends out and receives radio frequency (RF) energy.

• Modern electronic equipment, i.e. Personal medical devices such
as pacemakers, hearing aids, etc., are shielded from RF energy.
However, RF energy may affect some electronic equipment.

Five Year Limited Warranty

Golight, Inc. warrants the Stryker™ against any deemed defects
that are due to workmanship for parts or faulty materials, except
lamps, for five years from the date of the original purchase. This
warranty to the Stryker™ does not cover damage resulting from
unreasonable use or misuse, unreasonable maintenance or loss,
or labor costs.

Mounting the light upside down will void the warranty.

Warranty cards must be filled out and sent in within 30 days of
purchase to Golight, Inc. • RT 3 Box 37B • Culbertson, NE 69024,
for warranty protection. Register online at www.golight.com.

If the Golight® Stryker™ does fail to operate under warranted
specifications, send the light and remote control postage paid,
plus $9.95 for shipping and handling to: Golight, Inc. • Service
Department • RT 3 Box 37B • Culbertson, NE 69024. No C.O.D.'s
accepted. Only the above manufacturer is authorized to perform
warranty repair or replace product.

Any consequential damages to person or property are excluded
from this warranty. Some states do not allow the exclusion and
limitation of incidental or consequential damages, therefore the
above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights and you may also have
other rights.

You are now the owner of one of the finest

Congratulations

remote control searchlights available today.

Thank you for letting Golight® assist you in your

lighting application needs. We're proud

of our products and the technology that

we've developed to ensure our customers

the most durable, versatile and powerful

searchlights in the lighting industry.

Please read these instructions

before using your new

Golight® Stryker™.

• Vehicle electronic systems may be affected by RF energy.
Check with your vehicle manufacturer representative to be sure
that your Golight® Stryker™ will not affect the electronic system of
your vehicle.

RT 3 Box 37B • Culbertson, NE 69024

Golight, Inc.

800.557.0098 • 308.278.3131

[e-mail] • www.golight.com

U.S. Patent 5,673,989; 5,490,046

The Golight® Stryker™ is designed to permanently attach to a vehicle.

www.magnalight.com
1-800-369-6671
1-903-498-3363
[e-mail]

The 2-Speed Searchlight with Directional Flexibility is controlled by a
wireless remote, which gives the operator a full 370° horizontal
rotation and a 135° vertical tilt with fingertip control. The Stryker™
provides superior light penetration with the new Cr5 PentaBeam™ II
technology.

The Stryker™ Includes:

• Stryker™ Searchlight

• Remote Control

• 2 GP Super Alkaline Batteries 23A 12V

• Rockguard

• Permanent Mounting Gasket

• Permanent Mounting Plate

• Mounting Screws

MOUNTING INSTRUCTIONS

Determine the location for the light on your vehicle or boat. Center
the mounting plate with the vise screw on the mounting plate to the
back. Mark the hole locations for the three mounting screws and drill
a pilot hole for each with 1/8 inch bit. Fasten the stainless steel
mounting plate with the 3 #10 – 16x3/4 type AB cross recessed pan
head tapping screws, stainless steel. Drill a 1/4 inch hole in the center
mounting plate hole to accommodate a power cord. Install the
provided grommet in the hole. Bring the power cord through the
grommet. When connecting the positive and negative wires keep in
mind that the Stryker™ electronics are not polarized. You do not have
to be concerned with connecting the positive and negative wires
incorrectly. The 12volt DC power wire should be joined to the leads
under the lamp with appropriate automotive wire attachments. Keep
the wire connection above the mounting surface. It is recommended
that the power wire be connected to an ignition circuit or install a
separate on/off toggle switch between the light and the power
source.

Wet mounting surface with a small amount of water or lubricant for
easier installation, then place the light over the mounting plate by
sliding the front of the light over the front of the mounting plate, first
pull the light backwards, then seat the back of the light on to the

mounting plate. Displace the back of the gasket and install the vise
screw (provided). Tighten the vise screw using a Phillips head
screwdriver. Replace the gasket.

Each spotlight needs to be wired on a single dedicated circuit and the
power fused at 10 amps. With the power connected, your light is
ready for operation.

PROGRAMMABLE REMOTE INSTRUCTIONS

The Golight® Stryker™ is controlled with a programmable remote with
6561 different channels. This feature allows you the freedom to
change the channel selection, and the receiver relearns the new
selection.

PROGRAMMING THE TRANSMITTER.

This light has been pre-programmed at the factory, and it is not
necessary to re-program the transmitter, unless you experience
outside interference.

1. IMPORTANT: Disconnect power by removing fuse or
disconnecting vehicle battery.

2. Remove battery cover from remote control.

3. Set the 7 dip switches to a selection of your choice. There are 3

positions on each; positive, negative and neutral. Use a small
screwdriver and select a position for each dip switch. *Please note
that the orientation of the +/- switch positions may vary among
different models of wireless remote controls.

4. Insert both GP 23A 12V batteries. Be sure batteries have adequate
charge.

5. Replace battery cover.
a. Depress the on/off button and hold it down. Red LED will light.
b. While holding the on/off button down, reinstall the power
(replace fuse or connect vehicle battery).
c. Keep your finger on the on/off button for 5-6 seconds, and then
release. The light should now be programmed.

INSTALLATION OF WIRELESS DASH CONTROL

If you have a wireless dash control, please note that it is vital for this to
be attached to a flat / smooth surface with the 4 mounting screws
included. The arrow under the rubber cover should point up.

OPERATION OF STRYKER™

1. Using the remote control, turn on the light by depressing the
on/off button.

2. With the 4-way arrows on the remote control, rotate your light

to the desired location. Depending upon conditions, the
wireless remote may be used up to 100 feet from the Stryker™.

3. The speed of the light rotation can be controlled by depressing
the fast/slow button one time and by depressing it again to
restore the original speed.

4. The spotlight should not be turned on when the snap on lens
cover (rockguard) is attached.

BULB REPLACEMENT

The Golight® Stryker™ utilizes a Philips® 9011 bulb, which may be
purchased through Golight, Inc. — 308.278.3131 or 800.557.0098.

IMPORTANT SAFETY INFORMATION

✱ This symbol is to alert you to important operating or servicing

instructions that appear in your instructions. Always follow basic
safety precautions when using this product to reduce the risk of
injury, fire or electric shock.

✱ This light is for off road and utility use only. It is not designed for

road use as a driving light.

✱ The Stryker™ complies with Part. 15.105 of the FCC Rules. This

equipment has been tested and found to comply with the limits for a