Gold Wing CORVUS RACER EDGE540, EXTRA330SC, EXTRA260, YAK54, SUKHOI SU26M Assembly Manual

Goldwingrc is located in the centre of the model plane manufacturing community, the
beautiful coastal city of ZHUHAI, near Hong Kong and close to Macao.

Our general manager ,Paul, who has flown models for 15 years, has won the much
coveted 3D Championship of China, assuring you quality and design of GW products.

GW has a working facility of over 4000sq.Ft. With up-to-date equipment producing an
assortment of R/C model airplanes. Annual average production ranges from 20,000 to
30,000 pcs .Our current focus areas are electric and gasoline aircraft with specialist
accessories. The superior quality and 3D performance of these planes are highly
praised by our American ,European and Japanese customers.

We hope to establish long-term business relationships with friends from around the
world on the basis of mutual equality and benefit.

WWW.GOLDWINGRC.COM

Address: No.19, Western Jinfeng Rd,
Jinding science and technology
　 Zone, Zhuhai ,China
Postcode: 519028
Tel: [phone]
Fax: [phone]
Info email: [e-mail]
[e-mail]
[e-mail]

　　　　　　　　[e-mail]

100CC V3 SERIES

ASSEMBLY MANUAL

WWW.GOLDWINGRC.COM

YAK54／SUKHOI　SU26M／SUKHOI　SU29／MXS／SBACH342

CORVUS　RACER　EDGE540／EXTRA260／EXTRA330SC／YAK55M／YAK55SP

01

Thank you for purchasing this excellent almost-ready to fly R/C model!!! This ARF adopts the
latest 3Ddesign features and emphasizes high performance,light weight and fun.This plane is
designed by professional engineers and built by skilled craftsmen.Many of the parts are already　
pre-installed for you! We wish you great success in the assembly and flying of your new model.

Features:

1. Latest structure

2. Super quality

3. Easy installation

4. Carbon fiber wing tube

5.　　Carbon fiber tail wheel assembly
6．　Two pieces removable wings and stabs
7．　Extra strength epoxy control Horns
8．　Adjustable pushrods for easy fine tuning
9．　One piece carbon fiber landing gear
10．Advanced rubber wheels
11．Long servo arms included
12．Servo extension safety connector clips also included
13．Scale canopy and latest nilon bolts

14.　Fixed ring inside cowling for easy build

16. Pre-hinged control surfaces ready to fly

17. Pre-installed servo wire tube

18. Pre-mounted and plumbed gasoline tank ready to fly

19. Genuine ORACOVER film

20. Special 4．5in fiber spinner in SBACH300 and SBACH 342 included
21．Low wing loading makes it easy to fly
22．Light weight construction with high structural strength
23．Excellent aerobatics and 3D performance

If you have any problems and questions please contact GoldwingRC:

Address: No.19, Western Jinfeng Rd, Jinding science and technology

Zone, Zhuhai ,China

Postcode:519028
Tel:[phone]
Fax:[phone]
Info email: [e-mail] [e-mail]

　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　1642678762 ．

15．Removable　rudder　with　a　wire

@qq com

INTRODUCTION

[e-mail]

Attention

1.You should not regard this plane as toy!

2.Before the assembly please the careful reading instruction booklet, he can give you the full
detail instruction if you are the first contact airplane model public figure, should assemble
under the experienced correct instruction!

3.Please inspect in the packing all components, if lacks perhaps the damage, please
immediately with dealer relation.

4.As a result of weather temperature the moist change, the model outer covering possibly can
appear the phenomenon which relaxes, you may use the package to have a cotton fabric the iron
to burn again the outer covering smoothly, but must take care not to apply too much heat to one
area for long periods of time.

5.Inventory and inspect all parts and hardware for any imperfections or damage. Contact us
quickly if there are missing or damaged parts.

6.Fly only in AMA (Academy of Model Aeronautics) approved areas.

7.The manufacturer can not control the assembly, operation and maintenance of this product
therefore, We are not responsible for any damage that occurs as a result of the use or misuse of
this radio controlled model.

8.All GOLDWING products are guaranteed against defects within 30 days of receiving your
airplane. This warranty is limited to construction or production defects in both material and
workmanship. It does not cover any components or parts damaged by misuse or modification.

9.The purchaser accepts all responsibility of any and all structural or mechanical failures.

10.GoldWingRC reserves the right to make changes and amendments to construction manuals,
terms and conditions without notice.

10 8"(27 40 mm)

10 4．5"(2 65 0mm)

211 7s q. in(13 6. 6sq.d m. )

25 .3- 28 lbs(1 1500- 12 800 g)

Wing S pa n:

Wing S pa n:

Wing S pa n:

Length:

Length:

Length:

Wing Area:

Wing Area:

Wing Area:

Wei gh t:

Wei gh t:

Wei gh t:

Corvus　Race r　Ed ge 54 0

108"(2740mm)

104．5" (2 65 0m m)

2104sq.in.(135.8sq.dm.)

25 .3 -2 8l bs (11 50 0- 12 80 0g )

Extra260

10 8"(27 40 mm)

10 4．5"(2 65 0mm)

211 4s q. in(13 6. 4sq.d m. )

25 .3- 28 lbs(1 1500- 12 800 g)

Extra330S C

10 6"(26 90 mm)

10 2"(25 90 mm)

21 08 sq.in (1 36 sq. dm .)

25 .3- 28 lbs(1 1500- 12 800 g)

Yak55M

10 7" (2 72 0m m)

10 3. 5" (2 63 0m m)

21 05 sq .i n. (1 35 .8 sq .d m. )

2111s q. in .( 13 6. 2s q. dm .) 21 08 sq .i n. (1 36 sq .d m. ) 21 02 sq .i n. (1 35 .6 sq .d m. )

25 .3 -2 8l bs (11 50 0- 12 80 0g )

Yak54

10 7" (2 72 0m m)

10 8" (2 74 0m m) 10 7" (2 69 0m m)

10 2" (2 59 0m m)

10 4．5"( 26 50 mm ) 10 2" (2 59 0m m)

25 .3 -2 8l bs (11 50 0- 12 80 0g )

25 .3 -2 8l bs (11 50 0- 12 80 0g )

25 .3 -2 8l bs (11 50 0- 12 80 0g )

Sukhoi　Su26 M

Sukhoi　Su29

MXS

Flying

Flying

Flying

10 8"(27 40 mm)

10 4．5"(2 65 0mm)

211 1sq.i n( 13 6.2sq .d m.)

25 .3- 28 lbs(1 1500- 12 800 g)

21 03 sq .i n. (1 35 .7 sq .d m. )

10 7" (2 69 0m m)

10 2" (2 59 0m m)

25 .3 -2 8l bs (11 50 0- 12 80 0g )

Sbach342

YAK 55SP

02

Introduction -------------------------------------------------------------------­Attention-----------------------------------------------------------------------­Wing Assembly-----------------------------------------------------------------

Aileron Control Horns --------------------------------------------------------
　Aileron Servo Installation ----------------------------------------------------

Elevator Assembly -------------------------------------------------------------

Elevator Servo Installation ---------------------------------------------------
　Stap Tube Installation ---------------------------------------------------------

Rudder Assembly --------------------------------------------------------------

Rudder Horns and　Hinges ----------------------------------------------------
　Rudder Servo Installation -----------------------------------------------------
　Tail Wheel Installation --------------------------------------------------------

Main Landing Gear Assembly -----------------------------------------------

Landing Gear Installation ----------------------------------------------------
　Pants Installation --------------------------------------------------------------

Engine Installation ------------------------------------------------------------

Firewall Assembly -------------------------------------------------------------
　Engine Assembly --------------------------------------------------------------
　Throttle Servo Installtion ----------------------------------------------------
　Muffler Assembly -------------------------------------------------------------
　Hatch And Fuel Tank Ignition Module ---------------------------------------
　Ignition and battery assembly ------------------------------------------------

Cowl Assembly ----------------------------------------------------------------­Flight Preparation -------------------------------------------------------------

Wing Final assembly ----------------------------------------------------------
　Canopy assembly --------------------------------------------------------------
　Symmetry Control ------------------------------------------------------------
　Control Throws ----------------------------------------------------------------
　C.G Location -------------------------------------------------------------------
　Engine Debugging -------------------------------------------------------------

ACCESSORIES　LIST　-------------------------------------------------------­NEW　PRODUCT　------------------------------------------------------------­100CC　SERIES　PLANE　-----------------------------------------------------

01
02
04

04
05

06
06
08

09
10
11
13

14
15
16

17
17
18
19
20
22
23
24

25
25
26
26
27
27
27

28
32
33

TABLE OF CONTENTS

03

04

1.Scuff the horns with sand paper to
ensure a good glue bond.

3.Apply 30 minute epoxy inside the
pre-cut slots and coat the horns with
epoxy , Insert them into the pre-cut
slots. Wipe away excess glue with
rubbing alcohol.

2

Aileron Control Horns

1

3

Wing　Assembly

2.Pre－hinged　 control　 surface　 is　
ready　to　fly．Remove the covering
below to expose the pre-cut slots with a
knife. .

05

Aileron Servo Installation

2.The covering of the servo location
had been remove as shown.Put the end
of the servo extension in the servo
location.And then pull the extension
lea d throug h to the root of the
wing.Taping　servo　lead　to　the　inside　
of　the　wing　panel　will　help　to　
prevent　lead　from　dropping　back　
inside　 of　 wing　 panel　 during　
transportation．

4.Moun t t he servo ar m a nd the
extension arm with M2*8mm screws
and locking nuts as shown.Then turn on
the transmitter and plug the servo into
receiver. Ensure the channel is neutral.
Install the servo arm facing toward the
wing tip.Position the servo arm 90
degrees to the servo.

1.Use the provided safety clips to
secure the servo and servo extension
leads.

3.Drill 1mm holes for the servo
mounting screws. Position the servo
with the servo label closest to the wing
trailing edge. Use a drop of thick CA
glue on each screws to prevent tapping
sc r ew s fr o m lo o s e n i n g d ue t o
vibration. Install servo with M2*12mm
tapping screws.

Minimum Required Servo:180 in.oz / Metal Gear / Digital

M2*8mm screw

44

1

Serbo　extension　safety

Connector　clip

2

Taping　

3

Close　to　the
wing trailing

CA glue

1mm　bit

06

6. Repeat all the previous steps for the other　servo　and　 wing.

Elevator　Assembly

5. Install the arm pushrod and adjust the pushrod length to ensure the aileron
and servo are in the neutral position.

Epoxy horn

3mm latest nylon

ball link assembly

Anodized

AL

Long　servo　arm

3X60mm

Stainless　steel

Adjustable　pushrod

5

6

07

3.Position the servo with the servo wire
to the wire pre-slot. Drill 1mm holes
for the servo mounting screws using the
long aiguille.

4.Install servo with M2*12mm servo
mounting screws. Use a drop of thick
CA glue on each screw to prevent
sc r ew s fr o m l o o s e n i n g du e t o
vibration.

3

The serbo label
facing the hinge

2

1.Pre－hinged　 control　 surface　 is　
ready　to　fly．Remove the covering
below to expose the pre-cut slots with a
knife. .

2．Scuff the horns with sand paper to
ensure a good glue bond.Install the two
horns with M3*16mm scre w and
locking nut. Apply 30 minute epoxy
inside the pre-cut slots and coat the
horns with epoxy, Insert them into the
pre-cut slots.

2

Minimum Required Servo:180 in.oz / Metal Gear / Digital

Elevator servo installation

34

1

08

1.Use the provided safety clips to
secure the servo and servo extension
leads.

Stab Tube Installation

Repeat all the previous steps for the other　elevator．

3mm latest nylon

ball link assembly

Epoxy horn

Anodized

AL

Long　servo　arm

5.Turn on the transmitter. Make sure
the servo is in the neutral position.
Install the servo arm. Position the servo
arm 90 degrees to the servo,and tighten
the arm screw.

5

6.Insta l l t h e ar m p u shrod wi t h
M3*16mm screws. Adjust the pushrod
length so that the servo and elevator are
both in the neutral position.

6

1

4.Install the stab with M3*12mm
screws. Secure the screws with Blue
Loctite.

5.Repeat the previous steps for the
remaining stabilizer.

M3＊12mm　Screw

4

Rudder　Assembly

3．Slide the stab tubes in the fuse stab tube sleeves．

2.Run the extension lead through the fuselage to the receiver.

2

1

．

3

1

．

3

1

．

3

2

．

09

Pre－installed　

In　this　location

2

1

．

2

1

．

Pre－installed　servo　wire　tube

2

2

．

Pre－installed　servo　wire　tube

Rudder Horns　and　Hinges

1.Remove the covering below to
expose the pre-cut slots with a knife.

2. Scuff the middle of horns with sand
paper to ensure a good glue bond.
Apply 30 minute epoxy inside the pre­cut slots．

2

1

3．Coat the horns with epoxy. Insert
them into the pre-cut slots. Install　the　
ball　link　with　M3＊16mm　screws　and　
locking　nuts．Tightening　the　nuts　is　
recommended．Wipe　 away　 excess　
glue　 with　 rubbing　 alcohol．Make　
sure　the　horns　are　correctly　aligned　
and　symmetry　before　the　apoxy　has　
cured．

3

4

Tape

4．Keep　 the　 hinge　 holes　 in　 a　
line．Tape the rudder balance tab to the
top leading edge and the other location
of the vertical fin in the neutral
position as shown.

10

11

Rudder Servo Installation

The rudder cables and couplers have been pre-installed.

1. Drill 1mm holes for the M2*12mm
tapping screws. Fit the servos as shown
with t h e servo la b el facing the
rudder.Turn　on　the　transmitter．And　
then　install　AL　long　arm　on　the　
servo，position　the　servo　arm　90　
degrees　to　the　servo．

Minimum Required Servo:180 in.oz / Metal Gear / Digital

1

The servo label facing the rudder

L

Ф1.6*420mm steel wire

5

5.Fit the rudder by aligning the hinges
and inserting the hinge pin from the
bottom of the rudder　.The　length　of　
the　hinge　pin　is　enough　to　prevent　
the　falling　after　the　　installation　of　
the　wheel　tail．

　　Crimp

Pre－installed

3mm　ball　link

Pull　－pull　

Connector

Wire

Cable

2

3mm　bit

2mm　bit

Double－sided　tape

1

2

3

4

2.Drill 3mm holes in the AL long arm
for installing 3mm ball links and
screws.Drill　2mm　holes　in　the　servo　
arm　and　mount　it　with　2＊8mm　
screws　and　nuts．

12

L

L

3

3．Mount the pushrod into the ball links
and adjust the pushrod length same to
the length of servo arm gear.

4．Mount the pre-installed bolt link to
the servo arm with the M3*16mm
screws and the locking nuts.

4

5．Remove any slack in the cables and
crimp to secure. Crimp the brass swage
tu b e w i t h a cr i mp in g t oo l o r
pliers.Finally　you　can　adjust　the　
cable　by　loosening　or　tightｅning　the　
cable　connectors．

5

3mm　latest　

　link　assembly

Nylon　ball

13

1.Drill a 6mm hole and fit the steering
ball link.

2．Scuffing　the　ball　link　with　sand　
paper　to　ensure　a　good　glue bond　is　
suggestted　before　gluing． Make sure
the ball link hole is parallel to the
rudder.　Apply 30 minute epoxy inside
the 6mm hole and coat the hinges with
epoxy , Insert the ball link into the
hole.

3．Install the tail wheel with 8mm
lo c k i n g nu t s a nd thr e e w h e e l
collars.All wheel collars should be
secured with Blue Loctite.

6mm　bit

1

2

Tail　Wheel　Installation

3

14

Main　Landing　Gear　Installation

5．Insert the 2*225mm steel wire into the rudder steering ball link.Tighten the
set nut.

? 1 ．7*300 mm
steel wire

§¶1 ．5 ＊4 2 0 m m 　
steel wire

3mm　ball　link

Three　M3＊

12mm　screws

Removeable

　Rudder　with　

a　wire　

5

4

M3＊12mm　screws

4．Remove　the　cover　of　the　pre－
holes．And　mount　the　wheel　tail　
with　three　M3＊12mm　screws．

15

NOTE: the correct edge in mounting

Straight　edge　to

Front　of　fuse

1.Install the landing gear in the pre
drilled holes wi t h t h e s u p p l i e d
M4*25mm screws and locking nuts.
Don’t over tighten and crack the carbon
fiber.

2.Remove the covering below to
expose the holes with a knife and
reinstall the landing gear hatch cover.
Secure the M3*20mm screws with Blue
Loctite.The　hatch　cover　maybe　not　
included　in　some　planes．

3.Tighten the locking nut against the
landing gear strut.(for other planes)

M4＊25　socket　head
Screw　and　lock　nuts

．．．．．．4

1　

2

Landing Gear Installation

Align　axle　bolt　with　front　of　gear

3

16

4.Install the inner wheel collar on the axle. screw and tighten the wheel collar
in place. Adjust wheel collars in or out until wheel turns freely.

5.Repeat above steps for other wheel
and wheel pant.Final landing gear
installation shown below.

Pants Installation 1(For YAK series)

Pants Installation 2　(For　other　series)

M3＊20mm
Screw　and　lock

2

Nut

Ф5　Axle　and　
Wheel　collar

41

．．

42

．．

Ф5．1mm　

Wheel　collar

5

The　hatch　cover　maybe　not　included　in　some　planes

17

Firewall Assembly

Engine　Installation

Not　included　in　the　engine

DLE 111 engine（not　included）

1

1

．

1

2

．

1

2

．

1．Scuff　the　firewall　with　grater　to　ensure　easier　assembly　and　epoxy　it．

1.Install the inner wheel collar on the
axle. screw and tighten the wheel collar
in place. Adjust wheel collars in or out
until wheel turns freely.

2．And　then　install　the　wheel　pant　
with　two　M3＊12mm　screws．

2

1

1

．

18

Engine Assembly

2.Use　a　6mm　bit　to　drill　the　engine　mounting　holes　in　firewall．Using
M6*45mm mounting bolts，lock　nuts　and　flat fender washers mount engine
to firewall. Tighten the lock　nuts to prevent crushing of the firewall.

3.You can remove engine box top hatch cover for easier installation.

M6　flat　fender　washers

2

2

．

2

3

．

．

3

1

1

1.There are two pieces of wooden
t e m p l a t e s su p p l i e d , on e f o r
DA100，3W 106ccd　 and　 DLE111　
gasoline engine,the other one for ZDZ　
100B2NG engine. Select the right
template for your engine　to mark the
location of mounting holes. If other
engines are used the Universal template
may be modified for any mounting
pattern.

6mm　bit

2

1

．

2

2

．

2．Install　the　firewall　with　the　angle　aluminum，screws　and　lock　nuts．

2

1

．

19

3.Distance from front of firewall to front of engine prop hub should be
proper.Use wood washers to achieve correct distance.r　It　allows　for　better　
shock　absorption　if　you　mount　the　engine　with　the　rubber　washer．

Throttle Servo Installation

1.Position the hole and use a 6mm bit to
drill a pushrod exit hole in the firewall
in line with the engine carburetor
throttle arm.

2.Assemble ball link to threaded end of
pushrod.Thread ball link half way onto
pushrod to allow for proper adjustment
during final installation.

3. Mark the cut location for the throttle pushrod and remove pushrod from
throttle arm on carburetor and cut throttle pushrod to length.. Use a L bend to
connect the push rod to the servo arm.

6mm　bit

1　

Thread　ball　link　half

Way　onto　pushrod

2

2

＂L＂shape

3．

The　location　

Of　cutting

1

3．

1

3．

Rubber　washer

2

3．

（Not　included）

20

Muffler Assembly

4.Assemble the threaded end of pushrod to the servo arm as shown．Secure　the　
screw　with　blue　loctice．The　1－4steps　depends　on　the　type　of　the　engine．

5.Before mount the servo arm with
screws.Turn on the transmitter and
plug the servo into receiver. Ensure
every channel is neutral.Position the
s e r v o ar m 90 d e g r e e s to t h e
servo.Finally,Install the pushrod to the
servo arm.

42

．．

5

Included

41

．．

21

1. Use a knife to remove the cover from the pre-cut canister air　ｅxit opening.
2．Careful　 b end　 the　 flexｉble

manifold．　Use the silicone coupler and
clamps to join the manifold and the　
ｃanister muffler. There　are　two　sizes　
of　canister　mount　for　your　choice．　
．65mm　and　55mm．Mount the　65mm
caniste r m o u n t with the si l i c o n
insulators.

3．Use 30 Minute epoxy to secure the canister mount.Install the canister mount
in the fuse. Allow epoxy to fully cure before moving on to the next step.

4．Slide the canister into the canister tunnel.Secure the header in place using
the mounting bolts and gasket provided with your engine. Use blue Loctite to
secure the bolts.

1111

2

．．．．

1

1

．

2

41

．．

4．2

．

2

1

．

3

1

．

3

1

．

3

2

．

22

3. Tighten the tank to the cabin with the
VELCRO.

1111

2

．．．．

1.Fuel tube interface type has been
originally marked,nothing remains but
accord to connect well as show.

2.The tank bottom and cabin connect to the tank places had originally sticky

connected to the VELCRO.You　can　install　foam　rubber　pad　for　fuel　tank　
to　rest　on．foam　rubber　will　help　prevent　fuel　from　foaming　or　getting　
air　bubbles　from　engine　vibration．

Hatch And Fuel Tank

1

1

．

3

2

2

．

2

1

．

23

1.Position the ignition module on the
side of the engine mounting box and
mark the location of the nylon tie holes
as shown.

2.Use a 4mm bit to drill the ignition
module mounting holes.

3. Thread nylon tie through mounting holes. Trim two piece of foam rubber to

the ignition module. Make the pad slightly larger than the ignition
module.Mount the engine ignition module using nylon tie and foam rubber as
shown.

4.Repeat all the previous steps for the battery of ignition module.

1　

Safety　connect　clip

2

3．

4mm　bit

2

1

3．

Ignition 　and　the　battery　Assembly

Nilon　tie

The　Battery　of　ignition　module

1

4．

2

4．

24

5.Use the provided safety clips to
secure the ignition module and trigger
wire.And secure the battery and the
ignition module(via switch). Ensure
the plugs will not come apart from
vibration or light tension. Secure
ignitio n wire with nylon ties a s
necessary.

1．Remove the template and use a rotary cutting tool and sanding drum to cut
out the openings in the cowl. The shape and size of open pore depends on the
type of the engine.

Nylon　tie

5

1

1

．

1

2

．

Cowling　Installation

2.Secure　the　M3＊15mm　screws　with　
blue　loctite．Install the cowl with the
bolts and check that everything fits
correctly and nothing rubs against
cowl.

Wing final assembly

1.Slide the wing tube in the fuse wing tube sleeve.

2.Install the nylon bolts to the wing
blind nuts. Tighten snugly but do not
over tighten. Slide the wings on the
wing tube and plug in the aileron servo
connectors.

2

1111

2

．．．．

New　nylon　bolts

More　stronger

2

Flight　preparation

1

1

．

Ф36*937mm carbon fiber tube

25

NOTE：Special 4.5in fiber spinner of
SBACH300 and SBACH342 included.

Canopy 　Assembly

2.Install the canopy to the front of
fuselage,tighten the canopy with the
nilon bolts.

1

1

．

2

M3＊16

New　nylon　bolt

1

Symmetry Control

Adjust the aircraft and make sure both
sides are symmetrical.Like the diagram
shown.So that the plane is ready for
flight.

26

1111

2

．．．．

1．Us thin CA to secure front hatch hold down dowels.It is highly
recommended you apply thin CA glue to the front hold down dowels. This is a
High vibration area and can loosen the front dowels.

27

C．G　Location

Trial run the engine to check its stability at high speed and low speed to ensure
there are no problems with vibration on the model. Run the motor at high speed
about 30 seconds.Check the engine and make sure the temperature is below the
prescription of manufacturer.

Engine Debugging

Check every angle and adjust them to correct position.Check all parks and
make sure the installation is firm and reliable.Add some weight in either of

wingtip to balance the left and right wings.Once everything is right.....

Corvus　Racer　EDGE540

YAK54

EX TRA 260

EX TRA 330 SC

YAK55M

　MXS

YAK55S P

SU KHO I　S U26M SBACH342

SU KHO I　S U29

142mm

165mm 174mm 172mm 173mm

176mm

166mm

181mm

178mm

174mm

5.6　inch

6.5　inch 6.9　inch 6.8　inch 6.8　inch

6.9　inch

6.5　inch

7.1　inch

7.0　inch

6.8　inch

Control　Throws

ACCESSORIES

Epoxy　hornEpoxy　horn Epoxy　hornEpoxy　horn

AL　anodizedAL　anodized

AL　anodizedAL　anodized

Semi－long　armSemi－long　arm

Semi－long　armSemi－long　arm

M2＊8mm　screwM2＊8mm　screw

M2＊8mm　screwM2＊8mm　screw

M2　hexnutM2　hexnut

M2　hexnutM2　hexnut

M3　Ball　linkM3　Ball　link

M3　Ball　linkM3　Ball　link

M3＊16mm　hexM3＊16mm　hex

M3＊16mm　hexM3＊16mm　hex

Socket　screwSocket　screw

Socket　screwSocket　screw

M3　lock　nutM3　lock　nut

M3　lock　nutM3　lock　nut

M3＊60mmM3＊60mm

M3＊60mmM3＊60mm

Adjustable　Adjustable　

Adjustable　Adjustable　

PushrodPushrod

PushrodPushrod

ProvidedProvided

ProvidedProvided

Safety　clipsSafety　clips

Safety　clipsSafety　clips

Carbon　tubeCarbon　tube

Carbon　tubeCarbon　tube

Φ

36＊937mm

Φ

36＊937mm

ΦΦ

17＊937mm17＊937mm

WingsWings

M6＊28mm　M6＊28mm　
Nilon　boltNilon　bolt

M3＊16mmM3＊16mm

Screw　with　Screw　with　

WasherWasher

Stab　with　Stab　with　

ElevatorElevator

22

88

44

1616

1616

88

88

88

44

44

11

44

22

44

22

88

88

44

44

44

22

22

11

44

PicturePicture PicturePictureDescriptionDescription DescriptionDescription

QTYQTY QTY

28

29

PictureDescription

QTY

PictureDescription

QTY

Rudder

Epoxy　horn

3mm　ball　link

M3＊16mm

Hex　socket

Screw

M3　lock　nut

1．5＊420mm

Hinge　pin

AL　anodized

Long　arm

M2＊8mm　

Screw

M2　hexnut

M3＊40mm
Adjustable

Pushrod

Carbon　main
Landing　gear

M5＊16mm

Hex　socket

Screw

M5＊25mm

Hex　socket

Screw

M3　lock　nut

　Wheel　axle

F 5mm

Φ

Φ

5．1mm　

Wheel　collar

4＂ rubber
Pu　wheel

Wheel　pant

M3＊12mm

Screw

With　washer

Hatch　cover

1

2

4

6

8

1

2

8

8

2

1

1

4

4

2

4

2

2

4

1

M8　lock　nut

2

M3＊18mm

Hex　socket

Screw　

Picture

Description

QTY

Picture

Description QTY

Φ

Φ

Φ

Φ

Barbon　wheel

Tail　plate

M8　permanent

Seat　AL　screw

Lock　nut

4mm　wheel

Tail　wire

Wheel　collar

4mm

1．75＂　rubber

Pu　wheel

10mm　wheel

Tail　rockshaft

2mm　

Steel　wire

M3　ball　link

Firewall　board

Angle　aluminum

M3＊12mm　screw

With　washer

M3＊18mm　screw

With　washer

M3　lock　nut

Wood　template

Wood　washer

Carbon　spinner

（SBACH342

And　SBACH300）

M2＊8mm

Tapping　screw

2mm　upper

Firewall　board

2mm　firewall

Hatch　cover

2mm　under

Firewall　board

1

1

1

1

3

1

1

1

1

1

1

1

1

4

2

6

8

14

2

16

1

30

Picture

Description

QTY

Picture

Description QTY

1．7＊300mm

Φ

2mm　ball　link

2mm　nylon

L　bend

Hexnut

M2＊8mm　screw　

Servo　board

Servo　fortified

Board

Provided

Safety　clip

Cowl

M3＊16mm　screw

With　washer

Canopy

M3＊16mm　
Nylon　bolt

Decals　

Instruction　disk

5mm　allen　

Wrench

3mm　allen

Wrench

2mm　allen

Wrench

Fuselage　

1

1

1

1

1

2

3

2

1

6

1

4

1

1

1

1

1

1

31

Do you feel vexed,for damaging the wings in transport?

Give your plane the best protection!
Specialty wingbag can keep wings away from the impact and rubbing.

1.Special bag space to place wing tube ,hardware and other commom tools

2.According to the most popular wing planform.

3.Wearproof and waterproof drapery

4.Easier transport,you will be professional with the wingbag.

There are 30cc ,50cc, 100cc(85cc) and 150cc wingbags for your choice.

GW detrusion new product:KUZA-Wingbag.

Carbon spinner

KUZA wingbag

150cc(5＂),100cc(4.5＂),50cc(3.5＂) and 30cc(3＂) for your choice

32

NEW　PRODUCT

You　can　send　an　email　to　us　if　you　are　interest　in　the　product　above．
Email：[e-mail]

100CC　SERIES　PLANE

33

34

EXCLUSIVE DISTRIBUTORS IN THE WORLD