goldstein TK-24, TK-36, TK-30, TK-45 Installation Procedure – User Manual Service Instruction

TK-45

TEPPANYAKI

TEPPANYAKI

TEPPANYAKITEPPANYAKI

PROUDLY AUSTRALIAN MADE

INSTALLATION PROCEDURE – USER MANUAL
SERVICE INSTRUCTION

MODELS T

MODELS TKKKK----24 TK

MODELS TMODELS T

24 TK----30 TK

24 TK24 TK

30 TK----36 TK

30 TK30 TK

36 TK----45

36 TK36 TK

45

45 45

TK

TK----36

TK TK

36

3636

ESTABLISHED 1911

The Cooking Equipment Professionals

www.goldsteineswood.com.au

TABLE OF CONTENTS

1. INTRODUCTION Page 3

2. INSTALLATION Page 4 & 5

3. COMMISSIONING Page 6 & 7

4. OPERATING INSTRUCTIONS Page 8

5. PILOT & BURNER OPERATION Page 9

6. TECHNICAL INSTRUCTIONS Page 10

7. TECHNICAL DATA Page 11

8. CLEANING INSTRUCTIONS Page 12

9. PROBLEM SOLVING Page 13

10. TEPPANYAKI TABLE Page 16

11. DRAWINGS Page 17

12. SPARE PARTS-DRAWINGS Page 18

13. WARRANTY Page 19

14. BRANCHES Page 20

2

IMO83B1 – April 2011

1. INTRODUCTION

Congratulations for purchasing your Goldstein commercial cooking
appliance.
J. Goldstein & Co. is a wholly owned Australian company and has been
operating since 1911, building high quality products. The information in
this manual will assist your installer and ensure correct location and
connection. Thoroughly read the user instructions and the user
maintenance sections, as understanding your products, its operation, and
its cleaning and service requirements will provide you with long and
satisfactory service. Failure to do so could shorten the life of the product
and decrease its efficiency. Please ensure only authorised service
technicians are called to any difficulties that may arise.

INTRODUCTION

GOLDSTEIN TEPPANYAKKI

MODELS TK-24, TK-30, TK-36,TK-45

GOLDSTEIN TEPPANYAKI PLATES are designed to give long and satisfactory

service and incorporate the best possible materials and workmanship. Proper
installation, adjustment and preventative maintenance are vitally important if
efficiency and appearance are to be maintained.

Read these instructions carefully as they contain important safety information
regarding the installation, use and maintenance of the appliance.

RECEIVING INSPECTION

•

Check crates for handling damage. After carefully uncrating, check for
“concealed” damage. Report any damage immediately to carrier and to
dealer.

•

Remove check all loose items from unit and check contents as found on back
of warranty cards.

•

Check type and capacity of gas supply.

•

The type of gas for which this Teppanyaki is factory adjusted can be seen on
the rating plate, located on the front Control Panel.

“THE EQUIPMENT MUST BE INSTALLED BY A

LICENSED GAS FITTER”

3

IMO83B1 – April 2011

2. INSTALLATION INSTRUCTIONS

PRE-INSTALLATION OF THE TEPPANYAKI

1. Check that there is sufficient clearance between doors and passageways
to move equipment into the cooking area.

2. Remove banding and cardboard outer.

3. Lift off wooden base.

4. Push in legs and tap in with a hammer into tubes (If required mount on
stand (OPTIONAL)

INSTALLATION

(FOR AUTHORISED TECHNICIANS ONLY)

Note: AFTER ANY MAINTENANCE OR ADJUSTING OF GAS CONNECTED
COMPONENTS, A GAS LEAK TEST MUST BE CARRIED OUT, TO ENSURE
THERE ARE NO GAS LEAKING HAZARDS

Adequate ventilation must be provided by a hood with vent and exhaust fan.
Never make a direct connection between the unit and vent flue. Check there is
sufficient room between doors and other units to allow equipment to be moved
into position.
Check the data plate to ensure that the appliance is suitable for the gas supply to
which it is to be connected and for information relative to gas input. Etc.

Follow these instructions carefully.

1. Set unit in correct position (ENSURE THERE IS A MIN 25mm REAR

WALL CLEARANCE FROM COMBUSTIBLE MATERIALS AND THAT
THE UNIT IS PLACED ON A FIRE PROOF BASE) and adjust feet using a

spirit level, checking from back to front and side to side.

2 Have a licensed gas fitter or our local gas company connect the appliance

to the mains pressure supply.

NOTE:

The appliance must be installed by an authorised person and in accordance with
the regulations of the local Gas Authority, AS5601/AG601 and any other
authority having jurisdiction. The appliance has been tested and preset before
leaving our factory, but small adjustments may be necessary to suit local
conditions. Correct operation of the appliance must be tested as part of the
installation procedure.

The governor supplied must be installed on the gas inlet to the appliance. This is
supplied as a loose item. Licensed Gasfitter should make connection to main gas
line. Install a manual shut-off valve in gas line to the appliance manifold and
union.

NOTE: Models operating on LP Gas will be supplied with a regulator as from
(1st January 2005) as new standard (AS4563/AG300).

4

IMO83B1 – April 2011

2. INSTALLATION INSTRUCTIONS

3. All equipment must be sitting level for proper operation and combustion
where plinth type installation is made, plinth height and front overhang
must be 50 mm minimum. Levelling can be made by the use of metal
shims. For griddles where adjustable legs are provided, levelling can be
made easily due to the threaded construction of the legs.

Licensed plumber should make connection to main gas line. Install a
hand shut-off valve in gas line to the appliance manifold.

OVERALL DIMENSIONS

MODEL WxDxH
TK24 610 x 800 x 330
TK30 740 x 690 x 330
TK36 915 x 800 x 330
TK45 1120 x 690 x 330

5

IMO83B1 – April 2011

3. COMMISSIONING INSTRUCTIONS

OPERATION
(FOR AUTHORISED TECHNICIANS ONLY)

Note: All the appliances that leave our factory have been tested and
adjusted according to the specifications for the required gas. The regulator
may have to be adjusted to achieve the required gas pressure

Note: Before igniting the Teppanyaki plate, remove the protective coating
on the plate with solvent (e.g. mentholated spirits).

Ensure that the pressure at the pressure test point on the manifold is as per the
rating plate. If the pressure is not the same use a screwdriver to adjust the
pressure regulator (turning screw clockwise will increase the pressure).

Turn the control knob to low and check that the flame size has decreased
substantially. If flame has not decreased, then using a small flat headed
screwdriver adjust the “min gas screw” on the front of the gas control until the
min flame gets to desired size (turning screw clockwise will decrease the flame
size).

Turn the Teppanyaki plate off and apply a coating of cooking oil to the whole
griddle plate surface. Failure to do this will cause the warranty to be void.

FAILURE TO DO SO WILL VOID
WARRANTY ON THE EQUIPMENT

PLEASE RETURN YOUR WARRANTY CARD

NOTICE

6

IMO83B1 – April 2011