goldstein GPG-30, GPG-45, GPGDB-12, GPGDB-24, GPGDB/SA-24 Installation Procedure – User Manual Service Instruction

GAS GRIDDLE & COMBINATION GRILL AND
SALAMANDER TOASTER

PROUDLY AUSTRALIAN MADE

INSTALLATION PROCEDURE – USER MANUAL
SERVICE INSTRUCTION

MODELS GPG-30, GPG-45, GPGDB-12,24,36,48,
GPGDB/SA-24,36

GAS APPROVAL NO. 6006 & 6215

ESTABLISHED 1911

The Cooking Equipment Professionals

www.goldsteineswood.com.au

TABLE OF CONTENTS

1. INTRODUCTION Page 3

2. INSTALLATION Page 4

3. COMMISSIONING Page 5

4. OPERATING INSTRUCTIONS Page 6 & 7

5. LIGHTING INSTRUCTIONS Page 8

6. TECHNICAL INSTRUCTIONS Page 9

7. TECHNICAL DATA Page 10 & 11

8. CLEANING INSTRUCTIONS Page 12

9. PROBLEM SOLVING Page 13, 14 & 15

10. DRAWINGS - SPARE PARTS GPG-30,45 Page 16 & 17

11. DRAWINGS - SPARE PARTS- GPGDB/ SA-24,36Page 18 & 19

12. WARRANTY Page 20

13. BRANCHES Page 21

IM027B2/p2

1. INTRODUCTION

Congratulations for purchasing your Goldstein commercial cooking appliance.
J. Goldstein & Co. is a wholly owned Australian company and has been
operating since 1911, building high quality products. The information in this
manual will assist your installer and ensure correct location and connection.
Thoroughly read the user instructions and the user maintenance sections, as
understanding your products, its operation, and its cleaning and service
requirements will provide you with long and satisfactory service. Failure to do
so could shorten the life of the product and decrease its efficiency. Please
ensure only authorised service technicians are called to any difficulties that may
arise.

INTRODUCTION

GOLDSTEIN GAS GRIDDLE & COMBINATION GRILL AND
SALAMANDER TOASTER

MODELS GPG-30, GPG-45,GPGDB-12-24-36-48, GPGDB/SA-24,36

GOLDSTEIN GRIDDLES are designed to give long and satisfactory service and

incorporate the best possible materials and workmanship. Proper installation,
adjustment and preventative maintenance are vitally important if efficiency and
appearance are to be maintained.

Read these instructions carefully as they contain important safety information
regarding the installation, use and maintenance of the appliance.

RECEIVING INSPECTION

•

Check crates for handling damage. After carefully uncrating, check for “concealed”
damage. Report any damage immediately to carrier and to dealer.

•

Remove check all loose items from unit and check contents as found on back of
warranty cards.

•

Check type and capacity of gas supply.

•

The type of gas for which this Griddle is factory adjusted can be seen on the rating
plate, located on the front Control Panel.

“THE EQUIPMENT MUST BE INSTALLED BY A

LICENSED GASFITTER

Note The appliance must be installed by an Authorised person and in accordance with

the regulations of the local Gas Authority AS5601/AG601 and any other authority
having jurisdiction.

IM027B2/p3

2. INSTALLATION INSTRUCTIONS

PRE-INSTALLATION OF THE GRIDDLE

1. Check that there is sufficient clearance between doors and passageways to
move equipment into the cooking area.

2. Remove banding and cardboard outer.

3. Lift off wooden base.

4. Push in legs and tap in with a hammer into tubes (If required mount on stand
(OPTIONAL)

INSTALLATION

(FOR AUTHORISED TECHNICIANS ONLY)

Note: AFTER ANY MAINTENANCE OR ADJUSTING OF GAS CONNECTED
COMPONENTS, A GAS LEAK TEST MUST BE CARRIED OUT, TO ENSURE
THERE ARE NO GAS LEAKING HAZARDS

Adequate ventilation must be provided by a hood with vent and exhaust fan. Never
make a direct connection between the unit and vent flue. Check there is sufficient
room between doors and other units to allow equipment to be moved into position.
Check the data plate to ensure that the appliance is suitable for the gas supply to
which it is to be connected and for information relative to gas input. Etc.

Follow these instructions carefully.

1. Set unit in correct position (ENSURE THERE IS A MIN 25mm REAR WALL

CLEARANCE FROM COMBUSTIBLE MATERIALS AND THAT THE UNIT IS
PLACED ON A FIRE PROOF BASE) and adjust feet using a spirit level,

checking from back to front and side to side.

2 Have a licensed gas fitter or our local gas company connect the appliance to the

mains pressure supply. The gas inlet connection can be seen in the appendix.
The appliance must be installed in accordance with rules of any authority having
jurisdiction. The governor supplied must be installed on the gas inlet to the
appliance. This is supplied as a loose item.

3. All equipment must be sitting level for proper operation and combustion where
plinth type installation is made, plinth height and front overhang must be 50 mm
minimum. Levelling can be made by the use of metal shims. For griddles where
adjustable legs are provided, levelling can be made easily due to the threaded
construction of the legs.

Licensed plumber should make connection to main gas line. Install a hand
shut-off valve in gas line to the appliance manifold.

NOTE: Models operating on LP Gas are not supplied with a governor because none is
required.

WARNING
”DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS

IN OPERATION”

IM027B2/p4

3. COMMISSIONING INSTRUCTIONS

OPERATION
(FOR AUTHORISED TECHNICIANS ONLY)

Note: All the appliances that leave our factory have been tested and adjusted
according to the specifications for the required gas. The regulator may have to
be adjusted to achieve the required gas pressure

Note: Before igniting the griddle plate, remove the protective coating on the
plate with solvent (e.g. mentholated spirits).

After installation of the appliance the installer should light all burners to ensure that
they are operating correctly. The burner flames should not have yellow tips nor should
they be too “hard”. The aeration of each Burner can be adjusted by altering the
position of the shutter on the entrance to the throat of the Burner. Note GPGD/SA has
an adjustable bolt on the bottom of the Burner

If the appliance cannot be adjusted correctly for satisfactory operation, the matter
should be referred to the manufacturer or the local gas supply authority.

Ensure that the pressure at the pressure test point on the manifold is as per the rating
plate or as per page – of this manual. If the pressure is not the same use a
screwdriver to adjust the pressure regulator (turning screw clockwise will increase the
pressure).

Turn the control knob to low and check that the flame size has decreased substantially.
If flame has not decreased, then using a small flat headed screwdriver adjust the “min
gas screw” on the front of the gas control until the min flame gets to desired size
(turning screw clockwise will decrease the flame size).

Turn the griddle plate off and apply a coating of cooking oil to the whole griddle plate
surface. Failure to do this will cause the warranty to be void.

NOTE

WASH HOSES SHOULD NEVER BE USED ON THE APPLIANCE.

USE OF HOSES WILL VOID WARRANTY

NOTICE

PLEASE RETURN YOUR WARRANTY CARD
FAILURE TO DO SO WILL VOID
WARRANTY ON THE EQUIPMENT

IM027B2/p5

4. OPERATING INSTRUCTIONS

INSTALLING FRETS INTO THE GPGDSA

This procedure is to be followed after the unit has been mounted into desired position.

Note To avoid damage to frets only insert them into a row from the left hand side.
Note The first fret that you put into each row should be the far right hand fret. All

other frets follow, so that the frets are put into position from the right to the left.

Step 1 Turn fret onto its side with points facing to the right (refer Fig 1)>
Step 2 Holding the fret in your left hand move to below the left hand side of the

desired row (refer Fig 1)

Step 3 Lift fret up between the left hand burner and the side of the unit. Tilting fret

slightly, slide fret onto rails above burners, ensuring that the fret has the points
facing down (refer Fig 1).
Step 4Using your right and your left hand in conjunction, slide the fret to the right

hand side. The first fret that you put into each row should be the right hand fret,

which will be positioned above the space between the 2 far right burners. The

next fret put into the row should be positioned in the space to the left of the

previous fret. This should be repeated until the specified amount of frets are put

into each row. (Refer Fig.2).
Note Each fret should be located above the space between each burner:
For the GPGDSA-24 there will be 3 frets in each row.
For the GPGDSA-36 there will be 5 frets in each row.

Frets to be
placed points down

FRONT VIEW
FIG.2

IM027B2/p6

5. LIGHTING INSTRUCTIONS

A

Q

Q

OFF



B

 PILOT

XC

S

MAX

X D S

MIN

Q

ÎSPARKER TO LIGHT PILOT

G

A= OFF
B= IGNITION POSITION – LIGHT PILOT – (If flame failure hold in for 10

seconds to establish pilot flame).
C= TURN TO FULL ON – MAX GAS FLOW, FURTHER ADJUSTMENT

BETWEEN POSITIONS C & D.
D= TURN TO MINIMUM FLOW – MIN. GAS FLOW TO MAINTAIN FLAME

(Adjustable to suit type of gas used.) as precise and accurate.

TO OPERATE:

Push in and turn knob to position “B”, light pilot burner and hold in for 10
seconds to establish Pilot flame, release (pilot burner should remain alight) and
turn to position “C” for full flow of gas, for minimum gas flow turn to position
“D”
(Adjustable to suit type of gas used). Further adjustment of gas flow between
position C & D.

IM027B2/p7