Combo Pralinator/Corn Treat Model No. 2182EL/ER, 2182XL/XR
OPERATING INSTRUCTIONS
Controls and Their Functions
Heat/Motor Switch – This rocker switch in the “On” position energizes the heating elements in
the bottom of the kettle. It also activates the agitator motor based on the Pralinator/Corn Treat
switch setting (See description below). The Motor Only switch is off when using this switch.
Motor Only Switch – With this rocker switch in the “on” position, the agitator motor will run
continuously. This switch is used after the corn has been added to the caramel mixture for
blending the caramel corn. The Heat/Motor switch is turned off before activating this switch.
Pralinator/Corn Treat Switch – This rocker switch in the “Pralinator” position with the motor
switch “Off” will run the agitator motor 55 seconds of every minute. In the “Corn Treat” position,
the agitator motor will run 30 seconds of every minute.
1
3
4
Heat Control Key
Circular Arrow Key
Up/Down Arrow Keys
Heat/Motor Switch
Motor Only Switch
Paddle Timing Switch
6
ItemPart No.Model(s)Part DescriptionQty.
155506ALLHEAT CONTROL 1
242798ALLLIGHTED ROCKER SWITCH1
355507ALLDIGITAL NAMEPLATE1
51
655508ALL3DPT TOGGLE SWITCH1
486592182X10A, 277V, CIRCUIT BREAKER
Page 9
www.gmpopcorn.com
4
48616
ALL
DPDT ROCKER SWITCH
1
47364
2182
15A CIRCUIT BREAKER
5
2
Combo Pralinator/Corn Treat Model No. 2182EL/ER, 2182XL/XR
OPERATING INSTRUCTIONS
Controls and Their Functions
Heat/Motor Switch – This rocker switch in the “On” position energizes the heating elements in
the bottom of the kettle. It also activates the agitator motor based on the Pralinator/Corn Treat
switch setting (See description below). The Motor Only switch is off when using this switch.
Motor Only Switch – With this rocker switch in the “on” position, the agitator motor will run
continuously. This switch is used after the corn has been added to the caramel mixture for
blending the caramel corn. The Heat/Motor switch is turned off before activating this switch.
Pralinator/Corn Treat Switch – This rocker switch in the “Pralinator” position with the motor
switch “Off” will run the agitator motor 55 seconds of every minute. In the “Corn Treat” position,
the agitator motor will run 30 seconds of every minute.
1
3
4
Heat Control Key
Circular Arrow Key
Up/Down Arrow Keys
Heat/Motor Switch
Motor Only Switch
Paddle Timing Switch
6
ItemPart No.Model(s)Part DescriptionQty.
155506ALLHEAT CONTROL 1
242798ALLLIGHTED ROCKER SWITCH1
355507ALLDIGITAL NAMEPLATE1
51
655508ALL3DPT TOGGLE SWITCH1
486592182X10A, 277V, CIRCUIT BREAKER
Page 9
www.gmpopcorn.com
4
48616
ALL
DPDT ROCKER SWITCH
1
47364
2182
15A CIRCUIT BREAKER
5
2
Combo Pralinator/Corn Treat Model No. 2182EL/ER, 2182XL/XR
OPERATING INSTRUCTIONS
Controls and Their Functions
Heat/Motor Switch – This rocker switch in the “On” position energizes the heating elements in
the bottom of the kettle. It also activates the agitator motor based on the Pralinator/Corn Treat
switch setting (See description below). The Motor Only switch is off when using this switch.
Motor Only Switch – With this rocker switch in the “on” position, the agitator motor will run
continuously. This switch is used after the corn has been added to the caramel mixture for
blending the caramel corn. The Heat/Motor switch is turned off before activating this switch.
Pralinator/Corn Treat Switch – This rocker switch in the “Pralinator” position with the motor
switch “Off” will run the agitator motor 55 seconds of every minute. In the “Corn Treat” position,
the agitator motor will run 30 seconds of every minute.
1
3
4
Heat Control Key
Circular Arrow Key
Up/Down Arrow Keys
Heat/Motor Switch
Motor Only Switch
Paddle Timing Switch
6
ItemPart No.Model(s)Part DescriptionQty.
155506ALLHEAT CONTROL 1
242798ALLLIGHTED ROCKER SWITCH1
355507ALLDIGITAL NAMEPLATE1
51
655508ALL3DPT TOGGLE SWITCH1
486592182X10A, 277V, CIRCUIT BREAKER
Page 9
www.gmpopcorn.com
4
48616
ALL
DPDT ROCKER SWITCH
1
47364
2182
15A CIRCUIT BREAKER
5
2
Combo Pralinator/Corn Treat Model No. 2182EL/ER, 2182XL/XR
OPERATING INSTRUCTIONS
Controls and Their Functions
Heat/Motor Switch – This rocker switch in the “On” position energizes the heating elements in
the bottom of the kettle. It also activates the agitator motor based on the Pralinator/Corn Treat
switch setting (See description below). The Motor Only switch is off when using this switch.
Motor Only Switch – With this rocker switch in the “on” position, the agitator motor will run
continuously. This switch is used after the corn has been added to the caramel mixture for
blending the caramel corn. The Heat/Motor switch is turned off before activating this switch.
Pralinator/Corn Treat Switch – This rocker switch in the “Pralinator” position with the motor
switch “Off” will run the agitator motor 55 seconds of every minute. In the “Corn Treat” position,
the agitator motor will run 30 seconds of every minute.
1
3
4
Heat Control Key
Circular Arrow Key
Up/Down Arrow Keys
Heat/Motor Switch
Motor Only Switch
Paddle Timing Switch
6
ItemPart No.Model(s)Part DescriptionQty.
155506ALLHEAT CONTROL 1
242798ALLLIGHTED ROCKER SWITCH1
355507ALLDIGITAL NAMEPLATE1
51
655508ALL3DPT TOGGLE SWITCH1
486592182X10A, 277V, CIRCUIT BREAKER
Page 9
www.gmpopcorn.com
4
48616
ALL
DPDT ROCKER SWITCH
1
47364
2182
15A CIRCUIT BREAKER
5
2
Combo Pralinator/Corn Treat Model No. 2182EL/ER, 2182XL/XR
OPERATING INSTRUCTIONS
Controls and Their Functions
Heat/Motor Switch – This rocker switch in the “On” position energizes the heating elements in
the bottom of the kettle. It also activates the agitator motor based on the Pralinator/Corn Treat
switch setting (See description below). The Motor Only switch is off when using this switch.
Motor Only Switch – With this rocker switch in the “on” position, the agitator motor will run
continuously. This switch is used after the corn has been added to the caramel mixture for
blending the caramel corn. The Heat/Motor switch is turned off before activating this switch.
Pralinator/Corn Treat Switch – This rocker switch in the “Pralinator” position with the motor
switch “Off” will run the agitator motor 55 seconds of every minute. In the “Corn Treat” position,
the agitator motor will run 30 seconds of every minute.
1
3
4
Heat Control Key
Circular Arrow Key
Up/Down Arrow Keys
Heat/Motor Switch
Motor Only Switch
Paddle Timing Switch
6
ItemPart No.Model(s)Part DescriptionQty.
155506ALLHEAT CONTROL 1
242798ALLLIGHTED ROCKER SWITCH1
355507ALLDIGITAL NAMEPLATE1
51
655508ALL3DPT TOGGLE SWITCH1
486592182X10A, 277V, CIRCUIT BREAKER
Page 9
www.gmpopcorn.com
4
48616
ALL
DPDT ROCKER SWITCH
1
47364
2182
15A CIRCUIT BREAKER
5
2
Combo Pralinator/Corn Treat Model No. 2182EL/ER, 2182XL/XR
OPERATING INSTRUCTIONS
Controls and Their Functions
Heat/Motor Switch – This rocker switch in the “On” position energizes the heating elements in
the bottom of the kettle. It also activates the agitator motor based on the Pralinator/Corn Treat
switch setting (See description below). The Motor Only switch is off when using this switch.
Motor Only Switch – With this rocker switch in the “on” position, the agitator motor will run
continuously. This switch is used after the corn has been added to the caramel mixture for
blending the caramel corn. The Heat/Motor switch is turned off before activating this switch.
Pralinator/Corn Treat Switch – This rocker switch in the “Pralinator” position with the motor
switch “Off” will run the agitator motor 55 seconds of every minute. In the “Corn Treat” position,
the agitator motor will run 30 seconds of every minute.
1
3
4
Heat Control Key
Circular Arrow Key
Up/Down Arrow Keys
Heat/Motor Switch
Motor Only Switch
Paddle Timing Switch
6
ItemPart No.Model(s)Part DescriptionQty.
155506ALLHEAT CONTROL 1
242798ALLLIGHTED ROCKER SWITCH1
355507ALLDIGITAL NAMEPLATE1
51
655508ALL3DPT TOGGLE SWITCH1
486592182X10A, 277V, CIRCUIT BREAKER
Page 9
www.gmpopcorn.com
4
48616
ALL
DPDT ROCKER SWITCH
1
47364
2182
15A CIRCUIT BREAKER
5
2
Combo Pralinator/Corn Treat Model No. 2182EL/ER, 2182XL/XR
OPERATING INSTRUCTIONS
Controls and Their Functions
Heat/Motor Switch – This rocker switch in the “On” position energizes the heating elements in
the bottom of the kettle. It also activates the agitator motor based on the Pralinator/Corn Treat
switch setting (See description below). The Motor Only switch is off when using this switch.
Motor Only Switch – With this rocker switch in the “on” position, the agitator motor will run
continuously. This switch is used after the corn has been added to the caramel mixture for
blending the caramel corn. The Heat/Motor switch is turned off before activating this switch.
Pralinator/Corn Treat Switch – This rocker switch in the “Pralinator” position with the motor
switch “Off” will run the agitator motor 55 seconds of every minute. In the “Corn Treat” position,
the agitator motor will run 30 seconds of every minute.
1
3
4
Heat Control Key
Circular Arrow Key
Up/Down Arrow Keys
Heat/Motor Switch
Motor Only Switch
Paddle Timing Switch
6
ItemPart No.Model(s)Part DescriptionQty.
155506ALLHEAT CONTROL 1
242798ALLLIGHTED ROCKER SWITCH1
355507ALLDIGITAL NAMEPLATE1
51
655508ALL3DPT TOGGLE SWITCH1
486592182X10A, 277V, CIRCUIT BREAKER
Page 9
www.gmpopcorn.com
Combo Pralinator/Corn Treat Model No. 2182EL/ER, 2182XL/XR
New Paddle & Hub Seal Kit Installation
1. With the machine OFF, unplug the unit and allow it to cool.
2. Unscrew the wing bolts (Mixing Paddle - Lock Stud assemblies) and remove the mix
paddles.
3. Remove the old hub seal assembly.
4. Clean the area around the center hub. Clean up all food and carbon residue.
Note: The kettle shaft should be removed monthly and the bushings lubricated with
Never Seez® (use White Food Grade ONLY). To do this, loosen the (2) set screws in
the jaw coupling and remove the shaft. DO NOT lose the shaft key; this must be
reset into place when reassembling.
5. Remove any burrs on the top edge of the center hub. Use a fine grit emery paper to lightly
sand the surface. If the burrs are not removed, damage may occur to the new hub
assembly during installation.
6. Lightly lubricate the center hub of the kettle with a small amount of vegetable oil to allow
for easy installation of the hub seal assembly.
7. Slide the hub seal assembly down the agitator shaft. Apply pressure to ease the assembly
over the center hub of the kettle until it seats properly.
8. After the hub seal assembly has been properly installed, re-install the mix paddles onto
the agitator shaft.
9. Replace the wing bolts and finger tighten.
1
ItemPart No.Model(s)Part DescriptionQty.
146632ALLHUB SEAL ASSEMBLY1
246631ALLO-RING1
346630ALLOIL SEAL1
446629ALLHUB BODY1
2
3
4
Page 15
www.gmpopcorn.com
Combo Pralinator/Corn Treat Model No. 2182EL/ER, 2182XL/XR
New Paddle & Hub Seal Kit Installation
1. With the machine OFF, unplug the unit and allow it to cool.
2. Unscrew the wing bolts (Mixing Paddle - Lock Stud assemblies) and remove the mix
paddles.
3. Remove the old hub seal assembly.
4. Clean the area around the center hub. Clean up all food and carbon residue.
Note: The kettle shaft should be removed monthly and the bushings lubricated with
Never Seez® (use White Food Grade ONLY). To do this, loosen the (2) set screws in
the jaw coupling and remove the shaft. DO NOT lose the shaft key; this must be
reset into place when reassembling.
5. Remove any burrs on the top edge of the center hub. Use a fine grit emery paper to lightly
sand the surface. If the burrs are not removed, damage may occur to the new hub
assembly during installation.
6. Lightly lubricate the center hub of the kettle with a small amount of vegetable oil to allow
for easy installation of the hub seal assembly.
7. Slide the hub seal assembly down the agitator shaft. Apply pressure to ease the assembly
over the center hub of the kettle until it seats properly.
8. After the hub seal assembly has been properly installed, re-install the mix paddles onto
the agitator shaft.
9. Replace the wing bolts and finger tighten.
1
ItemPart No.Model(s)Part DescriptionQty.
146632ALLHUB SEAL ASSEMBLY1
246631ALLO-RING1
346630ALLOIL SEAL1
446629ALLHUB BODY1
2
3
4
Page 15
www.gmpopcorn.com
Combo Pralinator/Corn Treat Model No. 2182EL/ER, 2182XL/XR
New Paddle & Hub Seal Kit Installation
1. With the machine OFF, unplug the unit and allow it to cool.
2. Unscrew the wing bolts (Mixing Paddle - Lock Stud assemblies) and remove the mix
paddles.
3. Remove the old hub seal assembly.
4. Clean the area around the center hub. Clean up all food and carbon residue.
Note: The kettle shaft should be removed monthly and the bushings lubricated with
Never Seez® (use White Food Grade ONLY). To do this, loosen the (2) set screws in
the jaw coupling and remove the shaft. DO NOT lose the shaft key; this must be
reset into place when reassembling.
5. Remove any burrs on the top edge of the center hub. Use a fine grit emery paper to lightly
sand the surface. If the burrs are not removed, damage may occur to the new hub
assembly during installation.
6. Lightly lubricate the center hub of the kettle with a small amount of vegetable oil to allow
for easy installation of the hub seal assembly.
7. Slide the hub seal assembly down the agitator shaft. Apply pressure to ease the assembly
over the center hub of the kettle until it seats properly.
8. After the hub seal assembly has been properly installed, re-install the mix paddles onto
the agitator shaft.
9. Replace the wing bolts and finger tighten.
1
ItemPart No.Model(s)Part DescriptionQty.
146632ALLHUB SEAL ASSEMBLY1
246631ALLO-RING1
346630ALLOIL SEAL1
446629ALLHUB BODY1
2
3
4
Page 15
www.gmpopcorn.com
Combo Pralinator/Corn Treat Model No. 2182EL/ER, 2182XL/XR
New Paddle & Hub Seal Kit Installation
1. With the machine OFF, unplug the unit and allow it to cool.
2. Unscrew the wing bolts (Mixing Paddle - Lock Stud assemblies) and remove the mix
paddles.
3. Remove the old hub seal assembly.
4. Clean the area around the center hub. Clean up all food and carbon residue.
Note: The kettle shaft should be removed monthly and the bushings lubricated with
Never Seez® (use White Food Grade ONLY). To do this, loosen the (2) set screws in
the jaw coupling and remove the shaft. DO NOT lose the shaft key; this must be
reset into place when reassembling.
5. Remove any burrs on the top edge of the center hub. Use a fine grit emery paper to lightly
sand the surface. If the burrs are not removed, damage may occur to the new hub
assembly during installation.
6. Lightly lubricate the center hub of the kettle with a small amount of vegetable oil to allow
for easy installation of the hub seal assembly.
7. Slide the hub seal assembly down the agitator shaft. Apply pressure to ease the assembly
over the center hub of the kettle until it seats properly.
8. After the hub seal assembly has been properly installed, re-install the mix paddles onto
the agitator shaft.
9. Replace the wing bolts and finger tighten.
1
ItemPart No.Model(s)Part DescriptionQty.
146632ALLHUB SEAL ASSEMBLY1
246631ALLO-RING1
346630ALLOIL SEAL1
446629ALLHUB BODY1
2
3
4
Page 15
www.gmpopcorn.com
68015G
2182EL/ER
KETTLE ASSEMBLY
2
46153
ALL
2 POSITION BRACKET
1
4
55538
ALL
DIGITAL CONTROL BOX ASSEMBLY
1546006
ALL
TILT LEVER
1646028
ALL
HANDLE BAR GRIP
1
Item
Part No.
Model(s)
6
Combo Pralinator/Corn Treat Model No. 2182EL/ER, 2182XL/XR