Gold Medal Products 1087DC User Manual

© 2016 Gold Medal Products Co.

Part No. 110008

Instruction Manual

10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA

Olde New Orleans

Block Ice Shaver

Model No. 1087DC

Olde New Orleans

gmpopcorn.com

DANGER

Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.

008_051514

DANGER

Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.

014_020416

WARNING

This machinery contains sharp blades. Keep hands and body parts clear
at all times.

037_103114

WARNING

NEVER put your fingers into the shaver body (the goose-neck, ice chute, or
hopper). Serious injury may occur.

017_103114

WARNING

ALWAYS wear safety glasses when servicing this equipment.

010_010914

WARNING

No user serviceable parts inside. Refer servicing to qualified service
personnel.

011_051514

Block Ice Shaver Model No. 1087DC

SAFETY PRECAUTIONS

Page 2

Olde New Orleans

gmpopcorn.com

WARNING

Read and understand operator’s manual and all other safety instructions

before using this equipment. To order copies of the operator’s manual go to

gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862

022_060215

WARNING

DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.

012_010914

WARNING

This machine is NOT to be operated by minors.

007_010914

Block Ice Shaver Model No. 1087DC

SAFETY PRECAUTIONS (continued)

Note: Improvements are always being made to Gold Medal’s equipment. This

information may not be the latest available for your purposes. It is critical that
you call Gold Medal’s Technical Service Department at 1-800-543-0862 for any
questions about your machine operations, replacement parts, or any service
questions. (Gold Medal Products Co. does not assume any liability for injury due
to careless handling and/or reckless operation of this equipment.)

Page 3

Olde New Orleans

gmpopcorn.com

Drain Tray with Fitting

8 Oz. Sno-Kone®

Dipper

Drain Hose

Ice Pan

Ice Pick

Block Ice Mold

Block Ice Shaver Model No. 1087DC

INSTALLATION INSTRUCTIONS

Inspection of Shipment

After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).

Manual

Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold

Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.

Items Included with this Unit

Setup

This unit has been tested at the factory.

1. Remove all packaging and tape prior to operation.

2. Place unit on a sturdy, level base which can withstand accidental dripping of water

3. Connect the drain hose to funnel excess water to floor drain or basin tub. Drained

4. After setup, the unit should be cleaned prior to use (see Care and Cleaning section of

and ice.

water is not intended for human consumption.

this manual).

Page 4

Olde New Orleans

gmpopcorn.com

Block Ice Shaver Model No. 1087DC

Special Features

1. Model #1087DC uses block ice approximately 5" x 5" x 12" long.

2. Snow texture can be adjusted easily with varying the feed pressure applied to pusher

lever arm.

3. Cutter Head is equipped with three blades for rapid shaving.

4. Safety switch is installed to prevent operation of cutter head while shaver door is in an

open position.

5. Circuit Breaker Reset Switch in the event that a motor overheats.

Electrical Requirements

The following power supply must be provided:

1087DC: 12 Volts DC

Customer must supply 12 volt battery for proper machine operation.

Make sure to follow all safety precautions provided by the battery manufacturer.

Before You Connect Power to the Machine

1. Make sure all machine switches are in the OFF position before connecting to

the battery.

2. Cables must be attached to the proper polarity. Black is “+” positive;

white is “-” negative.

Note: If poles are reversed machine will not shave ice.

3. Install the unit in a level position.

Page 5

Olde New Orleans

gmpopcorn.com

Door
Switch

Top Hand Wheel
(sets Pressure Plate)

Pressure
Lever

Power
Switch

Circuit Breaker
Reset Switch

Block Ice Shaver Model No. 1087DC

OPERATING INSTRUCTIONS

Controls and Their Functions

POWER SWITCH – Turns on the power to the shaver motor.

DOOR SWITCH – A safety precaution which prevents machine operation when door is open.

CIRCUIT BREAKER – Protects the motor from overheating (locked rotor/mechanical failure

to start). Manual Reset, push black button to reset.

TOP HAND WHEEL – Applies pressure to the block ice loaded into the machine.

PRESSURE LEVER – Pressure applied on this lever determines the fineness or coarseness of the

shaved ice.

Using Your Machine

1. Allow ice to soften before use. When properly softened, ice will appear clear and not

frosted.

2. Lower cover door and load ice block. Set pressure plate by turning the top hand wheel

(failure to set pressure plate causes excessive load on driveline). After pressure is set
close the door.

NOTE: The machine will not to operate if the door is open.

3. Place ice pan directly below ice chute and engage power switch. With left hand on

pressure lever, force ice into shaver head. The amount of pressure applied at this point
will determine the fineness or coarseness of the shaved ice.

The last inch or so of the block of ice being shaved will typically break apart.

Page 6

Olde New Orleans

gmpopcorn.com

DANGER

Machine must be properly grounded to prevent electrical shock to personnel.

DO NOT immerse in water.

Always unplug the equipment before cleaning or servicing.

025_020314

WARNING

This machinery contains sharp blades. Keep hands and body parts clear
at all times.

037_103114

Block Ice Shaver Model No. 1087DC

Care and Cleaning

Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of
advertising your product.

Follow the directions below to clean and sanitize the unit after each day of use.

1. With the machine OFF, unplug the unit before attempting to clean.

2. Empty water from pans and clean using appropriate cleaners for the type of machine;

review all manufacturer’s instructions and warnings on cleaning product prior to use.

DO NOT use oven cleaners or abrasive materials as they will damage parts of the
machine.

DO NOT use Ammonia cleaners, they will damage plastic panels.

Page 7