Gold Medal Products 1087 Operators Manual
© 2016 Gold Medal Products Co.
Part No. 12517
Instruction Manual
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
Olde New Orleans
Block Ice Shaver
Model No. 1087
Olde New Orleans
gmpopcorn.com
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
This machinery contains sharp blades. Keep hands and body parts clear
at all times.
037_103114
WARNING
NEVER put your fingers into the shaver body (the goose-neck, ice chute, or
hopper). Serious injury may occur.
017_103114
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
Block Ice Shaver Model No. 1087
SAFETY PRECAUTIONS
Page 2
Olde New Orleans
gmpopcorn.com
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
Block Ice Shaver Model No. 1087
SAFETY PRECAUTIONS (continued)
Note: Improvements are always being made to Gold Medal’s equipment. This
information may not be the latest available for your purposes. It is critical that
you call Gold Medal’s Technical Service Department at 1-800-543-0862 for any
questions about your machine operations, replacement parts, or any service
questions. (Gold Medal Products Co. does not assume any liability for injury due
to careless handling and/or reckless operation of this equipment.)
Page 3
Olde New Orleans
gmpopcorn.com
Drain Tray with Fitting
8 Oz. Sno-Kone®
Dipper
Drain Hose
Ice Pan
Ice Pick
Block Ice Mold
Block Ice Shaver Model No. 1087
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Items Included with this Unit
Setup
This unit has been tested at the factory.
1. Remove all packaging and tape prior to operation.
2. Place unit on a sturdy, level base which can withstand accidental dripping of water
3. Connect the drain hose to funnel excess water to floor drain or basin tub. Drained
4. After setup, the unit should be cleaned prior to use (see Care and Cleaning section of
and ice.
water is not intended for human consumption.
this manual).
Page 4
Olde New Orleans
gmpopcorn.com
Block Ice Shaver Model No. 1087
Special Features
1. Model #1087 uses block ice approximately 5" x 5" x 12" long.
2. Snow texture can be adjusted easily with varying the feed pressure applied to pusher
lever arm.
3. Cutter Head is equipped with three blades for rapid shaving.
4. Safety switch is installed to prevent operation of cutter head while shaver door is in an
open position.
5. Safety Overload Protector in the event that a motor overheats.
Page 5
Olde New Orleans
gmpopcorn.com
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614
Block Ice Shaver Model No. 1087
Electrical Requirements
The following power supply must be provided:
Model: 120 Volts, 1248 Watts, 60 Hertz
A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle. We recommend this equipment be on a dedicated and protected circuit.
Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold
Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The
use of extension cords is not recommended due to safety concerns, and may cause sacrificed
and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
1. Make sure all machine switches are in the OFF position before plugging the equipment
into the receptacle.
2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the
power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install the unit in a level position.
Page 6
Olde New Orleans
gmpopcorn.com
Door
Switch
Top Hand Wheel
(sets Pressure Plate)
Pressure
Lever
Power
Switch
Reset
Switch
Block Ice Shaver Model No. 1087
OPERATING INSTRUCTIONS
Controls and Their Functions
POWER SWITCH – Turns on the power to the shaver motor.
DOOR SWITCH – A safety precaution which prevents machine operation when door is open.
RESET SWITCH – Protects motor from overheating (locked rotor/mechanical failure to start).
Manual Reset, push red button to reset.
TOP HAND WHEEL – Applies pressure to the block ice loaded into the machine.
PRESSURE LEVER – Pressure applied on this lever determines the fineness or coarseness of the
shaved ice.
Using Your Machine
1. Allow ice to soften before use. Ice, when properly softened, will appear clear and not
frosted.
2. Lower cover door and load ice block. Set pressure plate by turning the top hand wheel
(failure to set pressure plate causes excessive load on driveline). After pressure is set
close the door.
NOTE: The machine will not operate if the door is open.
3. Place ice pan directly below ice chute and engage power switch. With left hand on
pressure lever, force ice into shaver head. The amount of pressure applied at this point
will determine the fineness or coarseness of the shaved ice.
The last inch or so of the block of ice being shaved will typically break apart.
Page 7
Olde New Orleans
gmpopcorn.com
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water.
Always unplug the equipment before cleaning or servicing.
025_020314
WARNING
This machinery contains sharp blades. Keep hands and body parts clear
at all times.
037_103114
Block Ice Shaver Model No. 1087
Care and Cleaning
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of
advertising your product.
Follow the directions below to clean and sanitize the unit after each day of use.
1. With the machine OFF, unplug the unit before attempting to clean.
2. Empty water from pans and clean using appropriate cleaners for the type of machine;
review all manufacturer’s instructions and warnings on cleaning product prior to use.
DO NOT use oven cleaners or abrasive materials as they will damage parts of the
machine.
DO NOT use Ammonia cleaners, they will damage plastic panels.
Page 8
Loading...