Gold Medal Products 1009S Service Manual

Part No 67933

Sno–Konette

Instruction Manual

Deluxe – Model #1002S, 1002-01-100
Standard – Model #1003S, 1003SX
DC Model #1009S

Cincinnati, OH 45241-4807 USA

Sno-Konette

2

DANGER

DANGER

cause property damage, injury, or death. Any alterations to this equipment will

WARNING

WARNING

WARNING

WARNING

SAFETY PRECAUTIONS

Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.

Improper installation, adjustment, alteration, service, or maintenance can

void the warranty and may cause a dangerous condition. NEVER make
alterations to this equipment. Read the Installation, Operating, and
Maintenance Instructions thoroughly before installing, servicing, or operating
this equipment.

008_051514

014_051514

This machinery contains sharp blades. Keep hands and body parts clear
at all times.

NEVER put your fingers into the shaver body (the goose-neck, ice chute, or
hopper). Serious injury may occur.

ALWAYS wear safety glasses when servicing this equipment.

No user serviceable parts inside. Refer servicing to qualified service
personnel.

037_103114

017_103114

010_010914

011_051514

Models #1002S Series, 1003S Series, 1009S

Sno-Konette

3

WARNING

WARNING

WARNING

SAFETY PRECAUTIONS (continued)

Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862

DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.

022_060215

012_010914

This machine is NOT to be operated by minors.

Note: Improvements are always being made to Gold Medal’s equipment. This information may

not be the latest available for your purposes. It is critical that
you call Gold Medal’s Technical Service Department at 1-800-543-0862 for any
questions about your machine operations, replacement parts, or any service questions.
(Gold Medal Products Co. does not assume any liability for injury due
to careless handling and/or reckless operation of this equipment.)

007_010914

Models #1002S Series, 1003S Series, 1009S

Sno-Konette

4

Installation Instructions

Inspection of Shipment

After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).

Manual

Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold Medal
Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.

Items Included with this Unit

• Drain Hose

Setup

This unit has been tested at the factory.

1. Remove all packaging and tape prior to operation.

2. Place unit on a sturdy, level base which can withstand accidental dripping of water and ice.

3. Locate the pusher handle (packed in a separate box). Connect the pusher handle to the

shaver body using the bolt and nut provided.

4. Connect the drain hose to funnel excess water to floor drain or basin tub. Drained water is

not intended for human consumption.

5. After setup, the unit should be cleaned prior to use (see Care and Cleaning section of this

manual).

Models #1002S Series, 1003S Series, 1009S

Sno-Konette

5

DANGER

CAUTION

Electrical Requirements

The following power supply must be provided for:

1009S: 12 Volts DC - Customer must supply 12 volt battery for proper machine operation.

Make sure to follow all safety precautions provided by the battery manufacturer.
Cables must be attached to the proper polarity.

The following power supply must be provided for:

1002S, 1003S: 120 V~, 972 W, 60 Hz
1002-01-100, 1003SX: 230 V~, 972 W, 50 Hz

Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.

A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle. We recommend this equipment be on a dedicated and protected circuit.
Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold
Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The
use of extension cords is not recommended due to safety concerns, and may cause sacrificed
and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.

008_051514

Before You Plug In Machine

1. Make sure all machine switches are in the OFF position before plugging the equipment into

the receptacle.

2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the power

supply cord.

3. The wall outlet must have the proper polarity. If in doubt, have a competent electrician

inspect the outlet and correct if necessary.

4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).

5. Install the unit in a level position.

If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.

Models #1002S Series, 1003S Series, 1009S

039_080614

Sno-Konette

6

Operating Instructions

To Operate the Sno-Konette:

1. Fill the hopper to within an inch from the top with ice cubes or block ice (no larger than 3 to 4
inches). The larger the pieces, the better the snow.

2. Switch the motor on, and wait for it to reach full speed (this will take a minute or so).

3. Press the pusher handle down against the ice in the hopper. Apply firm and even pressure to
make the best snow. Practice will enable you to gauge when to stop. This allows the ice to
resettle against the shaver head. You may find that you need to relieve the pressure two or
three times during a cycle. Too much pressure will result in snow that is coarse; too little
pressure will make the snow mushy.

NOTE: Never allow any foreign or metallic objects around the shaver area of the Sno-Konette.
Ice picks, scoops, and debris that may be in the ice often damage blades.

Ice Requirements:

The Sno-Konette can take ice cubes or block ice, if you break the block into pieces
approximately 3 to 4 inches in size.

NOTE: The ice will not enter the shaving chute if the pieces are too large.

Models #1002S Series, 1003S Series, 1009S