10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
Page 2
Dogeroo, Super Dogeroo
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
SAFETY PRECAUTIONS
Page 2
gmpopcorn.com
Page 3
Dogeroo, Super Dogeroo
1 inch Dial Thermometer
9 inch Plastic Tongs
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control.
Setup
1. Your machine is fully assembled and tested at the factory. Carefully remove the
machine from the shipping cartons. Remove all packing material and tape.
2. If the optional sneeze guard has been purchased, place it over the corner posts.
3. Be sure to place your Dogeroo where the revolving hot dogs will attract the most
attention.
Accessories Included With Your Machine
Page 3
gmpopcorn.com
Page 4
Dogeroo, Super Dogeroo
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
Machine must be properly grounded to prevent electrical
shock to personnel. Failure to do so could result in serious
injury, or death.
Do NOT immerse any part of this equipment in water.
Do NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from
moisture.
Always unplug the equipment before cleaning or servicing.
Your electrician must furnish sufficient power for proper machine operation. We recommend
this equipment be on a dedicated and protected circuit. Failure to wire properly will void the
warranty and may result in damage to the machine. It is Gold Medal Products Company’s
recommendation that this machine be plugged directly into a wall outlet. The use of extension
cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced
performance.
Before You Plug In Machine
1. Make sure all machine switches are in the OFF position before plugging the equipment
into the receptacle.
2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the
power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter.
5. Install the unit in a level position.
Page 4
gmpopcorn.com
Page 5
Dogeroo, Super Dogeroo
On/Off switch
Heat Control
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
OPERATING INSTRUCTIONS
Controls and Their Functions
ON/OFF SWITCH
Flipping the lever of this switch to the "ON" position will energize the drive motor which
rotates the rotisserie. It also lights the bulb behind the front glass and completes the
circuit to the heat control.
HEAT CONTROL
The infinite heat control allows you to vary the operating temperature of the heating
element. When this control is in any position other that "OFF", the red pilot light will be
on. When the control is set at the "HI" position, the heating element is energized
continually.
Page 5
gmpopcorn.com
Page 6
Dogeroo, Super Dogeroo
Dogeroo
Super Dogeroo
Mini Dogeroo
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
Specifications for Each Machine
Model 8102
Model 8103
Model 8108
Hot Dogs 56 84 14
Buns 28 42 14
Operating Procedure
1. Pour 1 ½ quarts of water into the water pan (about 5/8" deep). This will keep the
buns moist and warm. Use hot water to speed the process. DoNOT overfill! Overfilling
will result in too much steam.
2. Place buns in the bun warmer basket.
3. Note: Some buns collect more moisture than others due to their texture.
4. Place the hot dogs on the rotisserie.
5. When ready to start cooking, move the toggle switch to the "ON" position. This will
rotate the rotisserie clockwise and light the bulb behind the silk screened sign.
6. The time required to broil the hot dogs will vary, depending upon size and
temperature (35-37° F refrigerated) of the hot dogs when placed in the Dogeroo.
With the heat control set on "HI" and using average size hot dogs, it will take from 10-15 minutes
to have the hot dogs ready for 145° F cook temperature. Watch the dogs carefully the first
several times you cook to avoid blistering or burning the hot dogs.
After the hot dogs are cooked, reduce the heat control setting to one which will keep the hot dogs
at the 140° F minimum serving temperature. Hot dogs can be kept on the rotisserie for several
hours without shriveling or loss of flavor, if the heat control is properly set.
Page 6
gmpopcorn.com
Page 7
Dogeroo, Super Dogeroo
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
CARE AND CLEANING
DANGER
Machine must be properly grounded to prevent electrical
shock to personnel.
DO NOT immerse in water.
Always unplug the equipment before cleaning or servicing.
Good sanitation practice demands that all food preparation equipment be cleaned regularly. A
clean looking, well-kept machine is one of the best ways of advertising your product.
The Dogeroo, Super Dogeroo, and Mini Dogeroo have been designed to disassemble quickly,
without the use of special tools, for easy cleaning.
1. Disconnect power supply cord. Be sure unit has cooled sufficiently to permit safe
handling.
2. Remove the condensate pan and basket from the bun warmer.
3. Remove the door from the bun warmer by sliding the pivot pin to the left or the right
to disengage.
4. Lift the bun warmer from the top of the top frame assembly. Lift out the water pan
from the top frame assembly.
5. Lift the power assembly from frame. This assembly must be cleaned by wiping with a
damp cloth.
6. Lift the left end of the rotisserie from the end support. Slide rotisserie to left and
disengage from motor coupling.
7. Lift out the drip pan. Slide the front and side glass upward in the slots designed in the
corner posts for glass removal.
8. All parts (except power assembly) may be immersed or flooded with water for
cleaning. Use a cleanser/sanitizer recommended or approved by your local Board of
Health. Wipe all parts dry.
9. Reassemble in reverse order.
Page 7
gmpopcorn.com
Page 8
Dogeroo, Super Dogeroo
Lift the left end of
Slide rotisserie
to left
Condensate
Water Pan
Lift Power Assembly
Bun Warmer
Removing
/Reassembly of
Removing
/Reassembly of
Rotisserie
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
Care and Cleaning – Pan and Rotisserie Removal/Reassembly
from frame.
Pan and
Basket
Removing/Reassembly of Pans
the rotisserie from
the end support.
Power Assembly
and disengage from
motor coupling.
Page 8
gmpopcorn.com
Page 9
Dogeroo, Super Dogeroo
Slide Glass Under Top
Lower Glass into Bottom channel
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
TROUBLESHOOTING
Hot Dogs are Dropping from the Cradle
The rotisserie cradle is bent. Be careful removing and reinstalling the cradles. Bent cradles will
not pivot freely in the rotisserie and can allow hot dogs to drop out as the unit rotates.
REPLACING BROKEN GLASS
If you accidentally break a panel of glass, it can be replaced very easily.
Note: Gold Medal Products Co. does NOT ship glass. Obtain replacement glass from
your local hardware store and always purchase double strength type glass.
1. Remove all loose pieces of glass.
2. Remove all rigid glass channels from around the glass to be replaced. Set it aside as it
must be reused.
3. Carefully remove the rest of the broken glass.
4. Apply decals (if desired) to the new glass panel.
5. Slide rigid glass channels over the exposed sides and bottom. Front and side glass slide
under top and is then lowered into bottom channel.
Glass Dimensions
Side Glass: 1/8" x 11 29/32" x 16 3/16 (All Models)
Front Glass: 1/8" x 13 29/32" x 16 3/16 (Model 8102 Dogeroo)
1/8" x 19 29/32" x 16 3/16 (Model 8103 Super Dogeroo)
1/8" x 8 29/32" x 16 3/16 (Model 8108 Mini Dogeroo)
Page 9
gmpopcorn.com
Page 10
Dogeroo, Super Dogeroo
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
MAINTENANCE INSTRUCTIONS
DANGER
Improper installation, adjustment, alteration, service, or
maintenance can cause property damage, injury or death.
Read the installation, Operating, and Maintenance
Instructions thoroughly before installing or servicing this
equipment.
DANGER
Do Not immerse the equipment in water. Unplug your
machine before servicing.
WARNING
Adequate eye protection must be used when servicing this
equipment to prevent eye injury.
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE
INTENDED ONLY FOR QUALIFIED SERVICE
PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL
EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
Page 10
gmpopcorn.com
Page 11
Dogeroo, Super Dogeroo
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or
parts list.
2. When ordering, please include part number, part name, and quantity needed.
3. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate) with your order.
4. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
Or, place orders by phone or online:
Phone: (800) 543-0862
(513) 769-7676
Fax: (800) 542-1496
(513) 769-8500
E-mail: info@gmpopcorn.com
Web Page: www.gmpopcorn.com
Page 11
gmpopcorn.com
Page 12
Dogeroo, Super Dogeroo
8102
EX 8103
EX 8108
EX
1 DOME (Bun Warmer)
1
87685
87723
87823
2 RUBBER BUMPER/FOOT
4
87247
87247
87247
3 KNOB
4
47120
47120
47120
4 8-32 X 3/8 PAN HD PH
M/S 4 12389
12389
12389
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
Cabinet Exterior – Front View
1
Item
Part Description Qty.
2
3, 4
Part Number
Page 12
gmpopcorn.com
Page 13
Dogeroo, Super Dogeroo
8102
EX 8103
EX 8108
EX
1 DOOR ASSEMBLY
1
87037
87121
87884
2 KNOB LID LIFT
1
47120
47120
47120
3 8-32 X 3/8 PAN HD PH M/S
1
12389
12389
12389
4 PIVOT PIN (rod to pivot hinge)
1
87069
87125
87885
5 CONDENSATE PAN
1
87034
87109
87937
6 BUN WARMER BASKET
1
87689
87725
87825
7 WATER PAN
1
87690
87726
87826
8 DRIP PAN
1
87082
87116
87218
Pivot Pin seen on
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
Cabinet Exterior – Back View
1
2, 3
4
5
Underside View of Door
6
7
8
Item
Part Description Qty.
Page 13
Part Number
gmpopcorn.com
Page 14
Dogeroo, Super Dogeroo
2
19 18
16
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
Power/Control Unit and Rotisserie
1
8
3
4
5
6
7
10 11
9
12
13
14
15
17
20
Page 14
gmpopcorn.com
Page 15
Dogeroo, Super Dogeroo
8102
EX 8103
EX 8108
EX
1 MOTOR AND ELEMENT SUPPORT
1
87668
87715
87815
2 HEAT REFLECTOR ASSEMBLY
1
87671
87717
87817
3 CONTROL
PANEL COVER
1
87669
87669
87669
4 SWITCH, LIGHTED ROCKER GR
1
42798
42798
42798
5 KNOB, HEAT SWITCH
1
47049
47049
47049
6 SWITCH PLATE
1
87733
EX 87734
EX 87932
ROTISSERIE ASSEMBLY
(includes Rotisserie
8 ROTISSERIE
1
87737
87153
87830
9 ROTISSERIE CRADLE
14
87740
87151
87831
10 END SUPPORT,
ROTISSERIE
1
87020
87020
87020
11 ¼-20 SERRATED NUT
2
46311
46311
46311
12 OFFSET STRIP
1
87079
87079
87079
13 HEAT ELEMENT
1
88160
EX 87123
87915
EX
14 BRACKET, ELEMENT
TIE DOWN
1
87080
87080
87080
15 STRAIN RELIEF
1
49740
49740
49740
16 POWER CORD
1
42369
42369
42369
17 MOTOR ASSEMBLY
1
87713
EX 87713
EX 87713
EX
18 SOCKET SUPPORT TUBE
1
87708
87728
87828
19 LAMP SOCKET
1
11034
11034
11034
20 PYGMY LIGHT
BULB
1
87444
87444
87444
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
Power/Control Unit and Rotisserie – Parts List
Item
7
and Cradles)
Part DescriptionQty.
1 87739 87127 87882
Part Number
Page 15
gmpopcorn.com
Page 16
Dogeroo, Super Dogeroo
8102
EX 8103
EX 8108
EX
1 INSULATOR TUBE
2
87039
87039
87039
2 8-32 SET SCREW
2
48040
48040
48040
3 INSULATOR BLOCK
1
87158
87158
87158
4 8-32 X
½ PH PAN SCREW
1
42226
42226
42226
5 8-32 SERRATED NUT
1
61151
61151
61151
6 FILTER, EMI 20 AMP
1
48695
48695
48695
7 MOTOR ASSEMBLY
1
87713EX
87713EX
87713EX
8 HEAT CONTROL
1
87301
87301
87301
Heat Control uses (2)
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
Power/Control Unit - Interior
1
2
3
4, 5
6
Phillips Screws M4X5
7
8
Item
Part Description Qty.
Part Number
Page 16
gmpopcorn.com
Page 17
Dogeroo, Super Dogeroo
1 1 IN. DIAL THERMOMETER
1
8000
2 9 INCH PLASTIC TONGS
1
87092
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
Accessories
2
1
Item
Part Description Qty. Part No.
Page 17
gmpopcorn.com
Page 18
Dogeroo, Super Dogeroo
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
WIRING DIAGRAM
Model No. 8102EX, 8103EX, 8108EX
Page 18
gmpopcorn.com
Page 19
Dogeroo, Super Dogeroo
10700 Medallion Drive, Cincinnati, Ohio 45241
-
4807 USA
and Mini Dogeroo Model No. 8102EX, 8103EX, 8108EX
WARRANTY
Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to
be free of defects in workmanship and material under normal use and service. Gold Medal
Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts,
f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and
which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point.
Except for “Perishable Parts” on specific machines, the above warranty applies for a period
of two (2) years from the date of original sale to the original purchaser of equipment when
recommended operating instructions and maintenance procedures have been followed. These
are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR
IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART,
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or
consequential damages. No claim under this warranty will be honored if the equipment covered
has been misused, neglected, damaged in transit, or has been tampered with or changed in any
way. No claim under this warranty shall be honored in the event that components in the unit at
the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty
is effective only when electrical items have been properly attached to city utility lines only at
proper voltages. This warranty is not transferable without the written consent of Gold Medal
Products Co.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person,
firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO.,
or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO
DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM,
AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR
REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.